Panasonic RXES29 Owner's manual

Category
CD players
Type
Owner's manual

This manual is also suitable for

Operating Instructions
使用说明书
Portable Stereo CD System
便携式立体声 CD 系统
Model No. RX-ES29
RX-ES23
Table of Contents
Supplied Accessories ........................................... 2
Precautions .......................................................... 2
Maintenance......................................................... 3
CD Selection ........................................................ 3
Location of Controls ............................................. 4
Use of Batteries.................................................... 6
Power Sources ..................................................... 6
Memory Batteries ................................................. 6
The Radio............................................................. 7
CDs and MP3 ....................................................... 8
Cassette Tape Play............................................. 10
Cassette Tape Recording ................................... 10
Setting the Clock ................................................ 12
The Play and Record Timer ............................... 12
The Sleep Timer................................................. 13
Sound Quality..................................................... 14
3-D Sound with the Sound Virtualizer ................ 14
Troubleshooting .................................................. 15
Specifications ..................................................... 15
Before connecting, operating or adjusting this product, please
read these instructions completely. Please keep this manual for
future reference.
在连接、操作或调整本产品之前,请完整阅读本说明书
请妥善保管本手册,以备日后参考。
[GC] [GS]
RQT7914-2G
GC_GCS_RQT7914-G.book 1 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
2
Dear Customer
Thank you for purchasing this product.
For optimum performance and safety, please read these
instructions carefully.
Supplied Accessories
Please check and identify the supplied accessories.
Use numbers indicated in parentheses when asking for
replacement parts.
Remote control transmitter (N2QAHB000048)...............1 pc.
AC power supply cord ....................................................1 pc.
Note:
The included AC power supply cord is for use with this unit
only.
Do not use it with other equipment.
For Saudi Arabia and Kuwait
For others
Precautions
Avoid using or placing this unit near sources of heat. Do not
leave it in an automobile exposed to direct sunlight for long
time with the doors and windows closed as this may deform
the cabinet.
Avoid cuts, scratches, or poor connections in the AC power
supply cord, as they may result in possible fire or electric
shock hazard. Also, excessive bending, pulling or splicing of
the cord should be avoided.
Do not unplug the AC power supply cord by pulling on the
cord. To do so may cause premature failure or shock hazard.
Do not operate this unit on AC outlet in a bathroom, as a
potential shock hazard may result.
When not in use, disconnect the AC power supply cord from
the household AC outlet.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE, DO NOT EXPOSE THIS
APPARATUS TO RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON
THE APPARATUS.
This product may receive radio interference caused by
mobile telephones during use. If such interference is
apparent, please increase separation between the product
and the mobile telephone.
THIS UNIT IS INTENDED FOR USE IN TROPICAL
CLIMATES.
CAUTION:
Change the voltage setting to suit the AC voltage in
your area. See page 6. Note that the unit will be
seriously damaged or fail to operate correctly if this
setting is not made correctly.
RQLS0218
Inside of product
GC_GCS_RQT7914-G.book 2 ページ 2005年3月23日 水曜日 午後4時37分
ENGLISH
RQT7914
3
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
Never use alcohol, paint thinner or benzine to clean this unit.
Before using chemically treated cloth, read the instructions
that comes with the cloth carefully.
For a cleaner crisper sound
Clean the heads after every 10 hours of use to assure good
quality playback and recording.
Use a cleaning tape (not included).
Cassette tape care
Tapes exceeding 100 minutes are thin and can break or get
caught in the mechanism.
Tape slack can get caught up in the mechanism and should
be taken up before the tape is played.
Endless tapes can get caught up in the deck’s moving parts if
used incorrectly.
CD Selection
Choose CDs with this mark: (A).
This unit can play CD-DA (digital audio)
format audio CD-R and CD-RW that have
been finalized (a process that enables
CD-R/CD-RW players to play audio CD-R
and CD-RW) upon completion of recording. It may not be able
to play some CD-R or CD-RW due to the condition of the
recording.
Do not
use CDs in irregular shape.
use CDs with labels and stickers that are coming off or with
adhesive exuding from under labels and stickers.
attach scratch-proof covers or any other kind of accessory.
write anything on the CD.
clean CDs with liquids. (Wipe with a soft, dry cloth.)
use CDs printed with label printers available on the market.
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A
BOOKCASE, BUILT-IN CABINET OR IN ANOTHER
CONFINED SPACE. ENSURE THE UNIT IS WELL
VENTILATED. TO PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE TO OVERHEATING,
ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION
VENTS.
DO NOT OBSTRUCT THE UNIT’S VENTILATION
OPENINGS WITH NEWSPAPERS, TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
DO NOT PLACE SOURCES OF NAKED FLAMES,
SUCH AS LIGHTED CANDLES, ON THE UNIT.
DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY
FRIENDLY MANNER.
The socket outlet shall be installed near the equipment
and easily accessible or the mains plug or an appliance
coupler shall remain readily operable.
Note on AC power supply cord
(For Saudi Arabia and Kuwait only)
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of AC
mains plug (figures A and B). Confirm the AC mains plug
fitted and follow the instructions below. Illustrations may
differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
2. Replace the fuse and close or attach the fuse cover.
Figure A Figure B
Fuse cover
Figure BFigure A
Fuse
(5 ampere)
Fuse
(5 ampere)
A
GC_GCS_RQT7914-G.book 3 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
4
1
2
<
6
5
?
A
=
4
9
8
<
3
9
7
6
5
2
4
8
:
:
;
R6, AA, UM-3
(not included)
Location of Controls
Main Unit
1
Deck
2 Deck eject button (< DECK) ................................. (l 10)
Press [< DECK] to open the deck.
(The unit comes on.)
Then, load a cassette and close the deck by hand.
3 Record/record pause button (¥/;) ................ (l 10, 11)
4 Cassette play button (1TAPE).............................. (l 10)
Press [1TAPE] to start play.
5 Band button (TUNER BAND) ................................... (l 7)
Press [TUNER BAND] to select “FM” or “AM”.
6 CD play/pause button (CD 1/;).........................(l 8, 9)
Press [CD 1/;] to start play.
Plays to the end of the CD and stops.
Press [CD 1/;] to pause halfway during play.
Press again to resume play.
7 CD recording mode button (CD REC MODE)....... (l 11)
8 Play timer/record timer button ( PLAY/REC) .... (l 13)
9 Clock/timer button (CLOCK/TIMER) ............... (l 12, 13)
: CD program/clear, tuner preset button
( MEMORY CLEAR) ........................................... (l 7, 9)
; Speaker
Note:
These speakers do not have magnetic shielding.
Do not place them near televisions, personal computers
or other devices easily influenced by magnetism.
< Standby/on switch ()
Press to switch the unit from on to standby mode or vice
versa. In standby mode, the unit is still consuming a small
amount of power.
= Sound equalizer button (SOUND EQ)................... (l 14)
> Tuning/CD search, Rewind/fast-forward, Album skip
buttons (REW/–/6, 5/+/FF)..................... (l 7, 8, 10)
Remote Control
1 Transmission window
Aim at the sensor, avoiding obstacles, at a maximum range
of 7 meters directly in front of the unit.
2 Sleep timer button (SLEEP)................................... (l 13)
3 Numeric buttons............................................... (l 7, 8, 9)
4 CD/MP3 play mode/FM mode button
(PLAY MODE).............................................. (l 7, 8, 9, 11)
5 Auto scan button (AUTO SCAN).............................. (l 7)
6 Display select button (DISPLAY).....................(l 10, 12)
Press [DISPLAY] to display the clock on the Display
panel B.
7 Preset channel select/album skip buttons
(C/: ALBUM, ALBUM9/D)....................... (l 7, 8)
8 Tuning/CD skip, search/MP3 track skip/clock/timer
adjust buttons (–/:, 9/+)................... (l 7, 8, 9, 12)
9 MP3 intro play button (INTRO) ................................ (l 9)
: Tape counter reset button (C.RESET) .................. (l 10)
Press [C.RESET] to reset the tape counter.
The counter resets to “000”.
; Tape rewind/fast-forward buttons
(6/REW, 5/FF ) ................................................ (l 10)
< Sound virtualizer button (S.VIRTUALIZER).......... (l 14)
When the unit is supplied with AC Power, the button such as 4
function in the same way as the controls on the main unit. To
save power, the unit cannot be turned on from the remote
control when batteries are used.
GC_GCS_RQT7914-G.book 4 ページ 2005年3月23日 水曜日 午後4時37分
5
RQT7914
? Tape/CD mode select/stop button
( TAPE/CD) ............................................. (l 8, 9, 10, 11)
Press [ TAPE/CD] to stop play.
@ Time adjust, Preset channel select/CD track select dial
(TIME/PRESET TUNE TRACK SKIP )........(
l
7, 8, 9, 11, 12)
A Volume control buttons (+, – VOLUME)........ (l 7, 8, 10)
Press [+, – VOLUME] to adjust to the desired volume
for CD, Tuner or Cassette.
B Display panel
C CD tray open/close button (< CD) ................... (l 8, 11)
Press [< CD] to open the tray.
(The unit comes on.)
Load a CD and press [< CD] to close the tray.
D Standby indicator (Í) (RX-ES29)
When the unit is connected to the AC mains supply, this
indicator lights up in standby mode and goes out when the
unit is turned on.
Standby/on indicator (Í/I) (RX-ES23)
The indicator lights green when the unit is turned on.
When the AC power supply is used, it functions as an AC
connection indicator. (The indicator colour changes to red
when the unit is turned off.)
E CD tray
F Remote control signal sensor (SENSOR)
30° 30°
7 m
Use
Keep the transmission window and the
unit’s sensor free from dust.
Operation can be affected by strong light
sources, such as direct sunlight, and the
glass doors of cabinets.
Batteries
Insert so the poles (+ and –) match those in the remote
control.
Remove if the remote control is not going to be used for a
long period of time. Store in a cool, dark place.
Replace if the unit does not respond to the remote control
even when held close to the front panel.
To Use Headphones (not included)
Reduce volume before connection.
Plug type: 3.5 mm stereo
Note:
Avoid listening for prolonged periods of time to prevent
hearing damage.
PHONESPHONES
e.g. CD
Do not
put heavy objects on the remote control.
take the remote control apart.
spill liquids onto the remote control.
GC_GCS_RQT7914-G.book 5 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
6
Use of Batteries
If this unit is not used for a long period of time or is used
only from an AC power source, remove all the batteries
to prevent potential damage due to possible battery
leakage.
Align the poles (+ and –) correctly when inserting the
batteries.
Do not mix old and new batteries or different types of
batteries.
Do not recharge ordinary dry cell batteries.
Do not heat or disassemble the batteries. Keep them away
from flame or water.
Do not keep together with metallic objects such as
necklaces.
Do not use rechargeable type batteries.
Do not use batteries if the covering has peeled off.
Mishandling of batteries can damage other items, cause
damage to the unit, and may cause a fire through
short-circuiting or electrolyte leakage.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with
any part of your body.
Power Sources
To operate the unit on AC power
(1)
[1] Use a flat head screwdriver to turn [VOLT ADJ] to
the voltage setting for your area.
[2] Connect the AC power supply cord. For areas
except Saudi Arabia and Kuwait:
Use the plug adaptor (not included) if necessary
(1)
.
2: Household AC outlet
3: AC power supply cord (included)
To use batteries (not included)
(2)
Disconnect the AC power supply cord from unit to operate on
battery power.
The remote control cannot turn the unit on when batteries are
used.
To remove the batteries [A]
Open the battery cover, insert a finger into the hole at the
bottom of the unit and push the batteries out.
Memory Batteries
Memory batteries retain memory (clock/timer/CD/radio
settings) during power supply interruption.
These batteries do not power the unit.
§
Memory batteries are not included.
To replace the batteries
(3)
The memory batteries last for about 1 year.
Connect the unit to AC power before replacing the batteries.
Extend the memory battery life by always pressing [] to
turn the unit off before disconnecting the unit from the AC
power source or replacing the power batteries.
To remove the batteries
(4)
Lift the negative end of the number 4 battery to remove
batteries.
Battery life
” flashes on the display when the batteries are
running down.
Then, the unit turns itself off and displays “U01”.
Replace all the batteries with new ones.
1
VOLT ADJ
110
127V
OFF
220
240V
VOLT ADJ
110
127V
OFF
220
240V
VOLT ADJ
110
127V
OFF
220
240V
OFF 110-127
V 220-240
V
(1)
AC IN
2
3
2
1
3
4
(3)
(R6/LR6, AA, UM-3)
(R20/LR20, D, UM-1)
5
12
43
6
8
7
(2)
[A]
outer
row
inner
row
(4)
1
2
4
3
GC_GCS_RQT7914-G.book 6 ページ 2005年3月23日 水曜日 午後4時37分
7
RQT7914
The Radio
Preparation:
When using batteries, press [].
Press [TUNER BAND] to select “FM” or “AM”.
Manual tuning
[1]
Press [REW/–/
6
] or [
5
/+/FF] to select a station.
To tune automatically
Press and hold [REW/–/6] or [5/+/FF] until the
frequency starts changing rapidly.
Auto tuning may be interrupted when there is excessive
interference.
To cancel auto tuning, press [REW/–/6] or [5/+/FF]
once again.
[2] Press [+, – VOLUME] to adjust volume.
To use auto scan
You can search for a station by listening to all tuned-in stations
for 8 seconds each.
[1] Press [AUTO SCAN].
[2]
Press [AUTO SCAN] when you find the desired station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
To improve FM sound quality
Press [PLAY MODE] to display “ ”.
Monaural sound is selected and noise reduces when reception is weak.
Press [PLAY MODE] again to cancel the mode.
To improve reception
FM : Change the length and direction of the antenna.
AM : Change the facing of the unit.
AM reception is briefly interrupted if [< DECK] is pressed.
To improve reception when using the unit in a building or
vehicle, place it near a window.
AM allocation setting
Only from the main unit
Before receiving AM broadcasts, be sure to select the correct
allocation setting (either 9 kHz or 10 kHz) for your area.
1 Press [TUNER BAND] to select FM.
2
Press and hold [TUNER BAND] for approximately 5 seconds.
The frequency display will be returned to the minimum frequency
of the AM band and the display will begin to flash. Keep holding
for approximately 5 more seconds.
3 When the display stops flashing and indicates a
different frequency number, release [TUNER BAND].
To return to the original frequency, repeat steps 1 to 3 above.
Note:
After changing the “allocation” setting, the frequencies you
previously preset into the memory will be cleared.
Preset tuning
Up to 16 stations can be set in the FM and AM band.
[1] Press [REW/–/6] or [5/+/ FF] to tune to the
required station.
[2] Press [ MEMORY CLEAR].
[3] While “ ” is flashing
Turn [TIME/PRESET TUNE TRACK SKIP ] to select
the channel and press [ MEMORY CLEAR] or on remote
control, press the numeric buttons to select channels.
For channels 1 to 9, press the corresponding number.
For channels 10 to 16, press [S10], then the two digits.
If “ ” goes off during presetting, return to step [1].
To select channels
Turn [TIME/PRESET TUNE TRACK SKIP ] to
select the channel or on remote control, press the
numeric buttons to select channels.
To use preset scan
You can search for a station by listening to all preset channels
for 8 seconds each.
[1] Press and hold [C/: ALBUM] or [ALBUM 9/
D] until “PS” appears on the display.
[2] Press [C/: ALBUM] or [ALBUM 9/D] when
you find the desired channel.
Preset scan ends after searching through each preset channel
once. To stop during the process, press [C/: ALBUM] or
[ALBUM 9/D].
To skip the preset channel,
1 Select the desired station.
2 Press [MEMORY CLEAR].
3 While “ ” is flashing
Turn
[TIME/PRESET TUNE TRACK SKIP ]
to display “– –”.
4 Press [ MEMORY CLEAR].
To select the skipped channel,
Press the numeric buttons.
VO
LUME
REW
AMFM
GC_GCS_RQT7914-G.book 7 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
8
CDs and MP3
To play a disc [CD-DA]
[MP3]
[1] Press [< CD] to open the
tray.
(The unit comes on.)
Label must face upward
(l right).
Load a CD and press [< CD]
to close the tray.
[2] Press [CD 1/;] to start play.
Plays to the end of the CD and stops.
When playing MP3, “MP3” is
displayed.
A: Track number
B: Elapsed play time
[3] Press [+, – VOLUME] to adjust volume.
One touch play (when using AC power)
When a CD is loaded, press [CD 1/;].
§
For skip tracks and skip album,
Press [CD 1/;] to start play if in the stop mode.
Note:
Keep this unit away from radios and televisions if interference
occurs.
Advanced CD and MP3 Functions
Preparation:
Press [TAPE/CD] to switch to CD mode.
Remote control only
Direct access play [CD-DA] [MP3]
Starts play from a selected track.
Press the numeric buttons to select and play your desired
track.
For 2-digits number: press [S10] once, then the 2 digits.
For 3-digits number: press [S10] twice, then the 3 digits.
Repeat play and Random play [CD-DA]
Repeat : plays a track or all tracks repeatedly.
Random : plays each track once in the random order.
Press [PLAY MODE] to select the desired mode.
Press [CD 1/;] to start play if in the stop mode.
Random can only be selected in the stop mode.
The play mode is also cancelled if the CD tray is opened.
Notes: (For Random Play)
Random play cannot be used together with program play.
Search can only be done during the current playing tracks.
During play you cannot select tracks with the numeric buttons
and skip to tracks which have already been played.
To Operations
stop play Press [TAPE/CD].
pause play Press [CD 1/;] during play.
skip tracks
§
Turn [TIME/PRESET TUNE
TRACK SKIP ] clockwise
(forward) or counter-clockwise
(backward). On remote control,
press [–/:] or [9/+].
search through tracks
[CD-DA]
Press and hold [REW/–/6] or
[5/+/FF] during play.
On remote control, press and hold
[–/:] or [9/+] during play.
skip album [MP3]
§
Press
[REW/–/
6
]
or
[
5
/+/FF]
.
On remote control, press
[
C
/
:
ALBUM]
or
[ALBUM
9
/
D
]
.
VO
LUME
CD
REW
TAPE CD
AB
e.g. MP3
To Operations
repeat the desired
track
Press [PLAY MODE] to select
“”.
repeat programmed
tracks
1 Start program play. (l 9)
2 Press [PLAY MODE] to select
“”.
cancel repeat play Press [PLAY MODE] until
” and “ ” are cleared.
cancel random play Press [PLAY MODE] to clear
“”.
If cancelled during play, play
continues to the end of the CD.
: (1 track- repeat)
(No display)
: (All-track repeat)
#
]
n
,
(===
]
n
,
===
GC_GCS_RQT7914-G.book 8 ページ 2005年3月23日 水曜日 午後4時37分
9
RQT7914
Repeat play and Album play [MP3]
You can play ( ) or repeat play ( ) tracks
only in the selected album.
Press [PLAY MODE] before or during playback to
select the desired mode.
( ): play all tracks in the selected album one time.
( )
: play all tracks in the selected album repeatedly.
You can select another album with album skip.
You cannot use random play with MP3.
MP3 Intro play
Intro functions allow you to start playing the 1st track of all
albums for 10 seconds each in the stop mode.
Press [INTRO] to start intro play.
Intro function is cancelled after playing the 1st track of last
album in the disc. To stop during the process, press [INTRO]
or [TAPE/CD].
Program play [CD-DA] [MP3]
You can program up to 24 tracks.
On the main unit
Preparation:
Press [TAPE/CD] to switch to CD stop mode.
[1] Turn [TIME/PRESET TUNE TRACK SKIP ] to
select the track.
[2] Press [ MEMORY CLEAR].
C: Programmed track
D: Play sequence
[3] Repeat step [1] and [2] to
program other tracks.
[4] Press [CD 1/;] to start play.
On the remote control
Preparation:
Press [STOP] to switch to CD stop mode.
[1] Press [PROGRAM/ CLEAR].
“”
appears on the display.
[2] Press the numeric button(s) to select the desired
track.
For 2-digits number: press [S10] once, then the 2 digits.
For 3-digits number: press [S10] twice, then the 3 digits.
Repeat this step to program other tracks.
[3] Press [CD 1/;] to start play.
The program remains intact even if play is stopped or the unit is
turned off.Cd-P for [CD-DA] or “P” for [MP3] appears when play
is stopped to indicate the contents are in the memory.
§
The mode is also cancelled if the CD tray is opened.
Notes:
“FULL” is displayed
If 24 tracks have already been programmed.
You can still program and play tracks if the total elapsed play
time of the program exceeds 200 minutes.
“– –:– –” is displayed [CD-DA].
This unit can play MP3, a method of compressing audio
without affecting audio quality.
ª When creating MP3 files to play on this unit
Disc format: ISO9660 level 1 and level 2 (except for
extended formats)
Title names and album names are not displayable on
this unit.
ª Limitation on MP3
This unit is compatible with multi-session but if there
are a lot of sessions it takes more time for play to
start. Keep the number of sessions to a minimum to
avoid this.
This unit cannot play files recorded using packet
write.
If a CD-ROM format CD contains MP3 and files other
than MP3, only the MP3 files will be playable.
Depending on how you create MP3 files, they may
not play in the order you numbered them or may not
play at all.
MPEG Layer-3 audio decoding technology licensed
from Fraunhofer IIS and Thomson multimedia.
OFF (no indication)
###
]
n
(====
,
To Operations
cancel
§
Press and hold [ MEMORY
CLEAR] in the CD stop mode
until “CLEAR” is displayed.
On remote control, press and
hold [PROGRAM/ CLEAR].
check the program
contents (while
“Cd-P” for [CD-DA] or
“P” for [MP3] is
displayed)
Turn [TIME/PRESET TUNE
TRACK SKIP ].
On remote control, press
[–/:] or [9/+].
C D
e.g. MP3
GC_GCS_RQT7914-G.book 9 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
10
Cassette Tape Play
[1] Press [<
DECK] to open the deck.
(The unit comes on.)
Load a cassette and close the
deck by hand.
A: Side to be played back facing
up.
B: Insert the cassette with the
exposed tape facing you.
[2] Press [1TAPE] to start play.
[3] Press [+, – VOLUME] to adjust volume.
§
when using AC power.
Cassette Tape Recording
Before Recording
Notes:
Use household AC power or new batteries when recording to
avoid poor recordings caused by the batteries running down.
Televisions can cause interference to recordings made on
this unit if they are too close to each other.
Selection of tapes
Use normal position tapes.
High position and metal position tapes can be played, but the
unit will not be able to record or erase correctly.
Volume and sound quality in recording
Recording level is set automatically.
Recordings are unaffected by changes to sound quality.
To display the tape counter while recording
Press [DISPLAY].
Each time you press the button in the CD or radio mode:
To reset the tape counter
Press [C.RESET].
The counter resets to “000”.
Erasure prevention
The illustration shows how to remove the tabs to prevent
recording. To record on the tape again, cover as shown.
A Side A
B Tab for side “B”
C Tab for side “A”
D Adhesive tape
To erase recordings
1 Press [< DECK] to open the deck and insert the cassette
with the side to be erased facing up.
2 Press [TAPE/CD] to switch to TAPE mode.
3 Press [¥/;].
Recording CDs
Normal recording
Preparation:
Wind on the leader tape.
[1] Press [< DECK] to open the deck.
[2] Press [TAPE/CD] to switch to CD mode.
[3] Press [¥/;] to start recording.
CD play and recording start at the same time.
The cassette stops when the CD finishes.
To Operations
stop play Press [TAPE/CD].
start one touch play
§
Press [1TAPE] when a cassette is
loaded.
fast-forward Press [5/+/FF]. On remote
control, press [5/FF].
rewind Press [REW/–/6].
On remote control, press
[6/REW].
REW
TAPE CD
VO
LUM
E
A
B
Present state Present time Tape counter
##
]
n
==========
]
n
,
=====
A
BC
A
D
GC_GCS_RQT7914-G.book 10 ページ 2005年3月23日 水曜日 午後4時37分
11
RQT7914
ALL-REC [CD-DA]
Records the whole CD or selected tracks. When the tape
finishes before CD, recording and CD pauses for you to resume
recording on the opposite side.
[1] Press [TAPE/CD] to switch to CD mode.
[2] Press [CD REC MODE] to display “ALL-REC”.
Each time you press the button:
The display shows the tape length needed.
“C – – – –” indicates the tape needed exceeds 100 minutes.
You can still record, but some tracks may not be recorded if
the tape is not long enough.
[3] Press [< DECK] to open the deck and load a
cassette with the side for recording facing up.
[4] Press [¥/;] to start recording.
The unit rewinds the tape, records 10 seconds of silence,
and then starts recording.
To stop recording, press [TAPE/CD]. The CD also stops.
If a track is interrupted at the end of the side facing up,
Recording and CD pauses.
§
The unit records 10 seconds of silence, and resumes
recording from the beginning of the cut-off track.
Note:
Random play and repeat play cannot be used with
ALL-REC”.
1-REC [CD-DA] [MP3]
Records a selected track from the CD and stops.
Preparation:
Wind on the tape to where you want to start recording.
[1] Press [TAPE/CD] to switch to CD mode.
[2] Press [CD REC MODE] to display “1-REC”.
[3] Turn [TIME/PRESET TUNE TRACK SKIP ] to
select the track you want to record.
[4] Press [¥/;] to start recording.
CD play and recording start at the same time.
Note:
Recording and CD will stop when the tape reaches its end,
even if the track has not finished.
Recording the Radio
Preparation:
To record from the beginning of the tape;
Wind on the leader tape.
To record from part or half way through the tape;
Wind on the tape to where you want to start recording.
[1] Load a cassette with the side for recording
facing up.
[2] Tune to the station.
[3] Press [¥/;] to start recording.
To reduce noise when recording AM (Beat Proof function)
Remote control only
1 Press [PLAY MODE] while recording.
Each time you press the button:
bP1 ,-. bP2
Choose the setting with the least noise.
To Operations
stop recording Press [TAPE/CD].
pause recording Press [¥/;].
continue recording
from another CD on
the same cassette
during pause or stop.
1 Press [< CD] and replace
the CD.
2 Press [¥/;].
Press again to resume
recording.
record selected tracks 1 Do step [1] and [2], then
program the tracks. (l 9)
2 Press [¥/;].
skip unwanted tracks 1 Press [¥/;] to pause
recording. (The CD also
pauses.)
2 Turn [TIME/PRESET TUNE
TRACK SKIP ] so the
next track you want to record is
displayed.
3 Press [¥/;] to resume
recording.
To Operations
record the track again
on the opposite side
1 Press [< DECK], flip the
cassette, and insert it.
2 Press [¥/;].
§
ALL-REC 1-REC OFF
##
]
n
=====
]
n
,
=====
To Operations
stop recording Press [TAPE/CD].
(The CD also stops.)
continue recording
from another CD
1 Press [< CD] and replace the
CD.
2 Do steps [3] and [4].
record a track in play 1 Press [CD REC MODE] to
display “1-REC”.
2 Press [¥/;].
Recording starts from the
beginning of the track and stops
when the track finishes.
To Operations
stop recording Press [TAPE/CD].
pause recording Press [¥/;].
Press again to resume recording.
GC_GCS_RQT7914-G.book 11 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
12
Setting the Clock
This is a 24-hour clock.
[1] Press [ ] to turn the unit on.
[2] Press [CLOCK/TIMER] to select “CLOCK”.
Each time you press the button:
[3] Within 10 seconds
Turn [TIME/PRESET TUNE TRACK SKIP ] to
set the time or on remote control, press [–/:]
or [9/+].
[4] Press [CLOCK/TIMER] to start the clock.
The original display is restored shortly after.
Note:
The clock may lose or gain some time over a period.
Readjust if necessary.
To display the clock
Remote control only
Press [DISPLAY].
The Play and Record Timer
You can set the timer to come on at a certain time to wake you
up (play timer) or to record a radio station (record timer).
Preparations:
Turn the unit on and set the clock.
For play timer, prepare the music source (tape/CD/radio) for
listening, and set the volume.
For record timer, check the cassette’s erasure prevention tab
(l 10) and load the cassette with the side for recording facing
up. Tune to the radio station (l 7), and set the volume.
To set the start and finish times
[1] Press [CLOCK/TIMER] to select the desired timer
function.
ON PLAY: to set the play timer
ON REC : to set the record timer
Proceed to step [2] before these indicators stop flashing
(about 10 seconds).
[2] Turn [TIME/PRESET TUNE TRACK SKIP ] to
set the start time and then press [CLOCK/TIMER].
[3] Turn [TIME/PRESET TUNE TRACK SKIP ] to
set the finish time and then press [CLOCK/
TIMER].
The start and finish times are now set.
VOLUME
TAPE CD
CLOCK
#
#
##
]
n
(
]
n
,
Original display
ON PLAY
OFF PLAY
ON REC
OFF REC
GC_GCS_RQT7914-G.book 12 ページ 2005年3月23日 水曜日 午後4時37分
13
RQT7914
To turn the timer on
[4] Press [ PLAY/REC] to display the timer
indicator.
Each time you press the button:
PLAY: to turn the play timer on
REC: to turn the record timer on
(The indicator does not appear if the start and finish times
have not been set.)
“E” appears if the clock has not been set.
[5] Press [ ] to turn the unit off.
The unit must be off for timer to operate.
The record timer comes on about 30 seconds earlier than
the set time.
§
While the unit is in standby mode and connected to the
household mains socket.
To change the settings (when unit is on)
You can enjoy your desired source after you have set the
timer.
Turn the unit off before the timer’s start time.
Note:
The play and record timers cannot be used together.
The Sleep Timer
Remote control only
You can set the unit to turn off after certain time. (e.g. when you
want to fall asleep while listening to music.)
Press [SLEEP] to select the time (minutes).
Each time you press the button:
Notes:
You can use sleep timer in combination with play and record
timer.
Make sure the unit is off before the play and record timer’s
start time.
Sleep-off time shall have higher priority than timer-off time.
To Operations
cancel the timer
Press [ PLAY/REC]. (l A)
check the settings
§
Press [CLOCK/TIMER]. (l B)
A : When the unit is on to clear the timer indicators from
the display. (The timer comes on at the set time
everyday if the timer is on.)
B : The settings are shown in the following order:
Start time > Finish time > Music source > Volume
> Original display
To Operations
change the times Do steps [1], [2], [3] and [5].
change the source or
volume
1 Press [ PLAY/REC] to clear
the timer indicator.
2 Make changes to the source or
volume.
3 Do steps [4] and [5].
No display (OFF)
##
]
n
===========
]
n
,
=====
PLAY REC
To Operations
cancel
Press
[SLEEP] to select
SLEEP OFF”.
check the remaining
time
Press
[SLEEP] once.
The remaining time is shown for
about 5 seconds.
change the setting
Press
[SLEEP] to select the new
time.
SLEEP 120SLEEP OFF
#
SLEEP 90SLEEP 60SLEEP 30
##
]
n
,
===
]
n
,
===
GC_GCS_RQT7914-G.book 13 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
14
Sound Quality
You can choose one of four types of sound quality.
1 Heavy: Adds punch to rock
2 Clear: Clarifies higher sounds
3 Soft: For background music
4 Vocal: Adds gloss to vocals
Press [SOUND EQ] to select a setting.
Each time you press the button:
1 Heavy > 2 Clear
e v
l 3 Soft
l v
l 4 Vocal
l v
EQ-OFF (cancelled)
Note:
Changes to sound
quality do not affect
recordings.
3-D Sound
with the Sound Virtualizer
Remote control only
You can create a three-dimensional sound field when listening
to stereo sound.
Press [S.VIRTUALIZER].
Press again to cancel.
Notes:
This feature does not affect recordings.
The actual effect depends on the source played.
SOUND EQ
1
3
4
2
]
n
=====
]
n
,
=====
#
=====
ON: OFF
GC_GCS_RQT7914-G.book 14 ページ 2005年3月23日 水曜日 午後4時37分
15
RQT7914
Troubleshooting
Before requesting for service, make the following checks. If you cannot fix the unit as described below, or if something not listed
here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Reference pages are shown as an example (l 3).
Common problems
CD
Cassette deck
Radio
Remote Control
Specifications
Radio
Frequency range
FM 87.50s108.00 MHz (50 kHz steps)
AM 522s1629 kHz (9 kHz steps)
520s1630 kHz (10 kHz steps)
CD player
Disc played
CD/MP3/CD-R/RW 8 cm/12 cm
Bit rate
MP3 32 kbpss320 kbps
Sampling frequency
CD 44.1 kHz
MP3 32 kHz, 44.1 kHz, 48 kHz
Decoding 16 bit linear
Beam source Semiconductor laser (wavelength 780 nm)
No. of channels 2-channel, stereo
Wow and flutter Below measurable limit
D/A converter MASH (1 bit DAC)
Tape recorder
Track system Stereo
Monitor system Variable sound monitor
Recording system AC bias
Erasing system Multi Pole magnet
Frequency range
Normal position 50s14000 Hz
General
Speakers (RX-ES29) 8 cm 5.4 k 2
(RX-ES23) 8 cm 2.7 k 2
Jacks
Output PHONES: 3.5 mm stereo (16s32 )
Power requirement
AC 110s127 V/220s240 V, 50/60 Hz
Power consumption: (RX-ES29) 33 W
(RX-ES23) 20 W
Battery 12 V [Eight R20/LR20 (D, UM-1) batteries]
Do not use rechargeable type batteries.
Memory back-up for computer/clock
6 V [Four R6/LR6 (AA, UM-3) batteries]
Do not use rechargeable type batteries.
Dimensions 529 mm (W) k 144 mm (H) k 276 mm (D)
Mass (RX-ES29) 4.4 kg without batteries
(RX-ES23) 3.9 kg without batteries
y
Notes:
Specifications are subject to change without notice.
Mass and dimensions are approximate.
“E” is displayed. Indicates incorrect operation. Read the instructions.
“U01” is displayed. Replace the batteries or use household AC power. (l 6)
“U02” is displayed.
Power batteries have not been inserted. Insert them or use household AC power.
(l 6)
CD will not play or CD display is
incorrect.
Place the CD with label facing up. (l 8)
Wait for 1 hour for condensation to dry and try again.
Certain sections are not played
properly.
Clean the CD. (l 3)
Replace the CD if it is scratched, warped, or nonstandard.
Recording is not possible. If the cassette’s tabs have removed, cover the holes with adhesive tape. (l 10)
Poor sound quality. Clean the heads. (l 3)
A lot of noise or tuning difficulty.
Interference may be caused by other equipment or the use of its remote control.
Turn the other equipment off or keep this unit away from them.
The remote control does not work.
Check to ensure the batteries are inserted correctly. (l 4)
Replace the batteries if they are worn. (l 4)
The unit cannot be turned on from
the remote control.
Turn the unit on from the main unit if you are using batteries to power the unit.
(l 4, 6)
Power consumption in standby mode
(RX-ES29) 3.0 W (117 V)
3.5 W (240 V)
(RX-ES23) 3.0 W (117 V)
3.5 W (240 V)
GC_GCS_RQT7914-G.book 15 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
16
亲爱的顾客
感谢您购买本产品。
有关本机器的最佳性能和安全性,请仔细阅读本说明书。
目录
随附的附件 ................................ 17
预防措施 .................................. 17
保养 ...................................... 17
CD 选择 ................................... 17
控件的位置 ................................ 18
使用电池 .................................. 20
电源 ...................................... 20
记忆电池 .................................. 20
收音机 .................................... 21
CD 和 MP3 ................................. 22
盒式磁带播放 .............................. 24
录制盒式磁带 .............................. 24
设置时钟 .................................. 26
播放和录制计时 .......................... 26
睡眠计时器 ................................ 27
音质 ...................................... 28
带有声音虚拟器的 3-D 音效 ................. 28
故障排除 ................................ 封底
规格 .................................... 封底
注意 !
本产品使用激光射线
控制器的使用调整及操作等如不遵照此处的说明进行
可能会受到激光辐射的危害
勿拆开机壳自行修理有问题请交给专业维修人员
警告
为了减少火灾触电或产品损坏的危请勿让本机遭受
受潮滴上或溅上水不要将诸如花瓶等盛水之物
于本机上
本产品在使用过程中
可能会受到移动电话的无线电波干扰
如果这种干扰明显的话请将本产品远离移动电话使用
本机供在热带气候地区使用
注意 !
为了确保良好的通风条件勿将本机安装或置于书柜
内藏式机柜或其它密闭的空间勿让窗帘或任何其它物
体堵塞通风孔以免因过热而造成触电或火灾危险
切勿让报纸桌布窗帘等物品堵塞住本机的通风孔
切勿将诸如点然的蜡烛等明火火源置于本机上
废弃处理电池时要尽量采取不破坏环境的方式
设备应放在交流电源输出插孔附近电源插头应放在出现故
障时能够便于插拔之处
注意
请变换电压的设定以配合您居住地区的 AC 电压详情
可参阅第 20 页 
应注意如果电压的设定不正确本机会受到严重的损坏
或不能正确地操作 
RQLS0218
产品内部
GC_GCS_RQT7914-G.book 16 ページ 2005年3月23日 水曜日 午後4時37分
17
RQT7914
随附的附件
请检查和核对随附的附件。
需要更换零件时,请使用括号中标明的编号。
遥控器 (N2QAHB000048) .......................... 1 个
AC 电源线 ...................................... 1 条
注:
随附的 AC 电源线仅用于本设备。
请勿将其用于其它设备。
用于沙特阿拉伯和科威特
用于其它地区
预防措施
避免在热源附近使用或放置本设备。请勿将其长时间搁置在门
窗紧闭、阳光直接照射的汽车内,否则可能会造成机壳变形。
避免使用切割、有划痕或接触不好的 AC 电源线,否则可能会
导致火灾或引起电击的危险。此外,还要避免电源线过度
曲、牵引或重叠。
请勿通过拉出电线的方式拔掉 AC 电源线,否则可能会导致老
化故障或电击的危险。
请勿在浴室内的 AC 插座上使用本产品,否则可能会引起电击
的危险。
不使用本设备时,请从家中的 AC 插座中拔出 AC 导线。
保养
如果表面附有灰尘
要清洁本设备,请使用柔软、干燥的布擦拭。
切勿使用酒精、涂料稀释剂或汽油清洁本设备。
在使用以化学方式处理过的布前,请仔细阅读布料附带
的说明书。
对于更加清晰的声音
每使用 10 个小时后清洁一次磁头,以确保良好的回放和
录制质量。
使用清洁磁带 (未随附)
盒式磁带的保养
超过 100 分钟的磁带很薄,可能会在设备中断裂或卡住。
磁带松弛会导致在设备中卡带,应在播放磁带之前将其解
决。
如果使用不当,则环形磁带可能会卡在卡座部件中。
CD 选择
选择带有此标记的 CD:(A)。
本设备可以播放 CD-DA (数码音频)格式的
音频 CD-R 和最终已完成录制的 CD-RW
(使 CD-R/CD-RW 播放机可以播放音频 CD-R
和 CD-RW 的过程)。由于录制条件的不同,
某些 CD-R 或 CD-RW 可能无法播放。
请勿
使用形状不规则的 CD。
使用标签和贴条快要脱落或粘胶已从标签或贴条下流出
的CD
贴上防刮擦的封面或任何其它类型的附件。
涂写 CD。
使用液体清洗 CD。(使用柔软、干燥的布擦拭。)
使用市售的标签打印机印刷的 CD。
A
GC_GCS_RQT7914-G.book 17 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
18
控件的位置
主机
1 卡座
2 卡座弹出按钮 (< DECK) ..................... (l 24)
按下 [< DECK] 以打开卡座。
(设备打开。)
然后,放入盒式磁带并手动关闭卡座。
3 录制 / 暂停录制按钮 (¥/;) ............... (l 24, 25)
4 盒式磁带播放按钮 (1TAPE) .................. (l 24)
按下 [1TAPE] 以开始播放。
5 波段按钮 (TUNER BAND) .................... (l 21)
按下 [TUNER BAND] 以选择 FM AM
6 CD 播放 / 暂停按钮 (CD 1/;) ............ (l 22, 23)
按下 [CD 1/;] 以开始播放。
播放至 CD 末端并停止。
按下 [CD 1/;] 以在播放中途暂停。
再次按下继续播放。
7 CD 录制模式按钮 (CD REC MODE) ............ (l 25)
8 播放定时器 / 录制计时器按钮 ( PLAY/REC) ... (l 27)
9 时钟 / 计时器按钮 (CLOCK/TIMER) ........ (l 26, 27)
: CD 节目 / 清除、调频预置按钮
(MEMORY CLEAR).................... (l 21, 23)
; 扬声器
注:
扬声器不具备磁屏蔽功能。
请勿将它们放置在易受磁性干扰的电视机、个人计算机或
其它设备附近。
< 待机 / 开机开关 ()
按下此键可将设备从开机模式切换到待机模式,反之亦然。
在待机模式下,设备仍会消耗少量电能。
= 声音均衡器按钮 (SOUND EQ) ................. (l 28)
> 调谐 /CD 搜索、快退 / 快进、唱片集跳过按钮
(REW/–/6, 5/+/FF) .............. (l 21, 22, 24)
遥控器
1 发射窗
对准传感器,避开障碍,设备前方最长的直线距离
为7米
2 睡眠定时器按钮 (SLEEP) ..................... (l 27)
3 数字键 .............................. (l 21, 22, 23)
4 CD/MP3 播放模式 /FM 模式按钮
(PLAY MODE)................... (l 21, 22, 23, 25)
5 自动寻台按钮 (AUTO SCAN) .................. (l 21)
6 显示屏选择按钮 (DISPLAY) ............... (l 24, 26)
按下 [DISPLAY] 以在显示屏面板 B 上显示时钟。
7 预置频道选择 / 唱片集跳过按钮
(C/:ALBUM, ALBUM9/D) ........ (l 21, 22)
8 调谐 /CD 跳过、搜索 /MP3 曲目跳过 / 时钟 / 计时器调节按钮
(–/:, 9/+) .................. (l 21, 22, 23, 26)
9 MP3 试听播放按钮 (INTRO) ................... (l 23)
: 磁带计数器重置按钮 (C.RESET) ............... (l 24)
按下 [C.RESET] 以重置磁带计数器。
计数器重置为000
; 磁带快退 / 快进按钮
(6/REW, 5/FF) ......................... (l 24)
< 声音虚拟器按钮 (S.VIRTUALIZER) ............. (l 28)
使用 AC 电源向本设备供电时,按钮
4 等的功能与主机上的
控件相同。要节省电量,当电池耗尽时无法通过遥控器打开
备。
1
2
<
6
5
?
A
=
4
9
8
<
3
9
7
6
5
2
4
8
:
:
;
R6, AA, UM-3
( )
GC_GCS_RQT7914-G.book 18 ページ 2005年3月23日 水曜日 午後4時37分
19
RQT7914
? 磁带 /CD 模式选择 / 停止按钮
( TAPE/CD) ................... (l 22, 23, 24, 25)
按下 [ TAPE/CD] 以停止播放。
@ 时间调节、预置频道选择 /CD 曲目选择盘 (TIME/PRESET
TUNE TRACK SKIP ) .... (l 21, 22, 23, 25, 26)
A 音量控制按扭 (+, – VOLUME) ......... (l 21, 22, 24)
按下 [+, – VOLUME] 以将 CD、调谐器或盒式磁带调节至
所需的音量。
B 显示屏面板
C CD 托盘打开 / 关闭按钮 (< CD) ........... (l 22, 25)
按下 [< CD] 以打开托盘。
(设备打开。)
放入 CD,然后按下 [< CD] 以关闭托盘。
D 待机指示灯 (Í) (RX-ES29)
当设备连接至 AC 电源时,该指示灯在待机模式下亮起,并
在设备打开时熄灭。
待机 / 开机指示灯 (Í/I) (RX-ES23)
当设备打开时,指示灯呈绿色亮起。
使用 AC 电源时,其作用与 AC 连接指示灯相同。
(设备关闭时,指示灯颜色更改为红色。)
E CD 托盘
F 遥控器信号传感器 (SENSOR)
30° 30°
7 m
使用
保持发射窗和设备传感器的清洁。
操作会受到强光源的影响,例如直射的阳
光和机壳的玻璃门。
电池
插入电池,使电极(+)与遥控器中的电极匹配。
如果长时间不使用遥控器,请取出电池。存放在凉爽
的暗处。
如果在遥控器靠近前面板执行操作时设备也没有任何反应
请更换电池。
使用耳机(未随附)
连接前降低音量。
插头类型:3.5 毫米立体声
注:
避免长时间聆听,防止听力受损
PHONESPHONES
请勿
在遥控器上放置重物。
拆解遥控器。
将液体泼溅到遥控器上。
例如 CD
GC_GCS_RQT7914-G.book 19 ページ 2005年3月23日 水曜日 午後4時37分
RQT7914
20
使用电池
如果长时间不使用本设备或仅使用 AC 电源,请取出所有的电
池,以防止可能由于漏电而造成潜在的损坏。
插入电池时,正确对准电极(+)。
请勿混用新旧电池或不同类型的电池。
请勿为普通的干电池充电。
请勿加热或拆解电池。远离烟火或水。
请勿与金属物件共同放置,例如项链。
切勿使用充电型电池
请勿使用外壳已剥落的电池。
错误使用电池会对其它零件和本设备造成损坏,并可能由于短
路或电解液泄漏而引发火灾。
如果电池漏液,请与经销商联系。如果身体沾染了漏液,请彻
底用水清洗。
电源
通过 AC 电源操作设备
(1)
[1] 使用平头螺丝起子将 [VOLT ADJ] 转至您所在地区的
电压设置。
[2] 连接 AC 电源线。适用于沙特阿拉伯和科威特以外的
地区:
如有必要,请使用插头转接器(未随附)(1)。
2:家庭 AC 插座
3:AC 电源线 (随附)
使用电池(未随附)(2)
从设备上断开 AC 电源线,将电池用作电源。
使用电池时,无法使用遥控器打开设备。
取出电池 [A]
打开电池盖,将一个手指插入设备底部的小洞中,然后推出电
池。
记忆电池
在电源中断的过程中,记忆电池保留记忆 (时钟 / 计时 /CD/
收音机设置)
电池不会向设备供电。
§
不包括记忆电源。
更换电池 (3)
记忆电池可持续使用约 1 年。
在更换电池之前,将设备连接至 AC 电源。
在断开 AC 电源或更换电池前始终按 [] 关闭设备,可
以延长记忆电池的寿命。
取出电池 (4)
抬起电池 4 的负极端以取出电池。
电池寿命
电池耗尽时,显示屏上的 「」闪烁。
然后,设备自动关闭,并显示 U01
用新电池更换所有电池。
1
VOLT ADJ
110
127V
OFF
220
240V
VOLT ADJ
110
127V
OFF
220
240V
VOLT ADJ
110
127V
OFF
220
240V
OFF 110-127
V 220-240
V
(1)
AC IN
2
3
(4)
1
2
4
3
GC_GCS_RQT7914-G.book 20 ページ 2005年3月23日 水曜日 午後4時37分
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Panasonic RXES29 Owner's manual

Category
CD players
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages