CEN-TECH 37772 Owner's manual

Category
Multimeters
Type
Owner's manual

This manual is also suitable for

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
REV 14f
Owners Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2004 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 37772 61593
SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety ..........................................2
Specifications ..............................6
Setup ...........................................5
Operation ..................................... 7
Maintenance ............................... 11
Warranty .....................................12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Safety Warnings and Precaustions
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. Electrical shock can cause death
or injury! NEVER TOUCH exposed
conductors of electricity.
2. Inspect the Multimeter before
use. In addition to a general
inspection, look specifically for:
a. Pay special attention to the
insulation protecting the connectors.
b. Check the leads for exposed metal,
damaged insulation, and continuity.
c. Replace damaged test lead
immediately, before use.
3. Do not use the multimeter if:
a. The test lead is damaged
in any way.
b. The battery is low.
c. Near any explosive
gasses or fumes.
Page 3For technical questions, please call 1-888-866-5797.Item 37772 61593
SAFETYOPERATIONMAINTENANCE SETUP
d. Any abnormal operation is
detected.
(If in doubt about the condition
of the meter, have it serviced.)
e. The battery cover is open.
4. This meter should be powered only by
a single, correctly installed 9V battery.
5. Use caution when working near
voltages above 30 VAC rms, 42 VAC
peak, or 60 VDC. Voltages this high
present a risk of electric shock.
6. Disconnect the circuit’s power
before connecting the meter in
series, when measuring current.
7. Connect the common (COM) test
lead first and disconnect it last.
8. Hold the probes with fingers
behind guards.
9. Avoid electrical shock. Use extreme
caution when working near uninsulated
conductors or bus bars. Prevent body
contact with grounded surfaces such
as pipes, radiators, ranges, and cabinet
enclosures when testing voltages.
10. Observe work area conditions. Do
not test voltages in damp or wet
locations. Don’t expose to rain.
Keep work area clean and well lit.
11. Keep children away. Children must
never be allowed in the work area.
12. Stay alert. Watch what you are doing,
use common sense. Do not operate
any meter when you are tired.
13. Do not operate meter if under the
influence of alcohol or drugs. Read
warning labels on prescriptions to
determine if your judgment or reflexes
are impaired while taking drugs. If there
is any doubt, do not operate the meter.
14. WARNING: This product contains
lead, a chemical known to the State
of California to cause cancer and
birth defects or other reproductive
harm. (California Health &
Safety Code § 25249.5, et seq.)
15. WARNING: The cord of this product
contains lead, a chemical known
to the State of California to cause
cancer, and birth defects or other
reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
16. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference
or pacemaker failure.
17. Do not test voltage on circuits higher
than 750 volts AC or 1000 volts DC.
This type of testing should only be
done by a qualified electrician.
18. Do not test current on circuits
higher than 20 mA.
19. Store idle equipment. When not
in use, meters must be stored in a
dry location to decrease exposure
to moisture. Lock up meters and
keep out of reach of children.
20. Dress properly. Protective,
electrically nonconductive
clothes and nonskid footwear are
recommended when working.
21. Wear ANSI-approved safety
goggles during use.
22. Only use accessories intended
for use with this meter.
Page 4 For technical questions, please call 1-888-866-5797. Item 37772 61593
SAFETY OPERATION MAINTENANCESETUP
23. The warnings, cautions, and
instructions discussed in this
instruction manual cannot cover all
possible conditions and situations
that may occur. It must be understood
by the operator that common sense
and caution are factors which cannot
be built into this product, but must
be supplied by the operator.
24. Avoid damaging meter. Use only
as specified in this manual.
25. Prior to testing, resistance, diodes,
or continuity; disconnect all power
to the circuit and discharge all
high-voltage capacitors.
26. Performance of this meter may vary
depending on battery condition.
27. Use the proper settings, terminals,
techniques, and range for the
tests performed. Start with the
range stated in the instructions.
28. Do not apply voltage to the Test
Leads when the Multimeter is in
the Ohms testing setting. Damage
can occur to the multimeter.
29. Do not switch between testing
modes with the multimeter
connected to a circuit.
30. Do not use the meter at a setting
marked as blank on the scale.
31. Prior to testing capacitors, resistance,
diodes, or continuity; disconnect all
power to the circuit and discharge
all high-voltage capacitors.
32. Have the Multimeter calibrated by
a qualified technician every year. A
multimeter that is not calibrated yearly
may not yield accurate results.
SAVE THESE INSTRUCTIONS.
Page 5For technical questions, please call 1-888-866-5797.Item 37772 61593
SAFETYOPERATIONMAINTENANCE SETUP
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Functions
AC Volt
Section
DC Volt
Section
AC Current
Section
DC Current
Section
Resistance
Section
V/Ω/Hz
Jack
COM
Jack
mA
Jack
20A
Jack
Capacitance
Section
Frequency
Section
Transistor
(hFE) Section
Diode
Position
Continuity
Position
Temperature
Section
Temperature
Measuring
Socket
Range
Selector
Switch
Transistor
Testing Socket
Capacitance
Testing
Socket (Cx)
Power
Hold
Page 6 For technical questions, please call 1-888-866-5797. Item 37772 61593
SAFETY OPERATION MAINTENANCESETUP
Specifications
Max. Voltage 1000Vdc/700rms ac (sine)
DC Voltage Ranges: 200mV/2/20/200/1000V
DC Voltage Accuracy (@200mV-200V) 0.5% of rdg ±1D;
(@1000V) 0.8% of rdg ±2D
AC Voltage Ranges: 200mV/2/20/200/700V
Frequency Range: 40-400Hz
AC Voltage Accuracy (@200mV) 1.2% of rdg ±3D;
(@2-200V) 0.8% of rdg ±3D;
(@700V) 1.2% of rdg ±3D
DC Current Ranges:200μA/2mA/20mA/2A/10A
DC Current Accuracy (@ 200μA-20mA) 0.8% of rdg ±1D
(@200mA-2A) 1.5% of rdg ±1D
(@10A) 2% of rdg ±5D
AC Current Ranges: 200μA/2mA/20mA/2A/10A
Frequency Range: 40-400Hz
AC Current Accuracy (@ 200μA&200mA) 1.8% of rdg ±3D
(@ 2mA-20mA) 1.0% of rdg ±3D
(@ 10A) 3.0% of rdg ±7D
Resistance Ranges: 200Ω/2KΩ/20KΩ/200KΩ/2MΩ/20MΩ
Resistance Accuracy (@200Ω) 0.8% of rdg ±3D;
(@2K-2MΩ) 0.8% of rdg ±1D;
(@20MΩ) 1.0% of rdg ±2D;
Capacitance Ranges: 2nF/20nF/200nF/2μF/20μF
Capacitance Accuracy (@2nf-20μF) 4.0% of rdg ±3D
Frequency Range: 20KHz
Frequency Accuracy (@20KHz) 1.5% of rdg ±5D
Temperature Range: -20° to 1000°C
Temperature Accuracy (@-20° to 0°C) 5.0% of rdg ±4D
(@ 0° to 400°C) 1.0% of rdg ±3D
(@ 400° to 1000°C) 2.0% of rdg
Sampling Rate 2-3 times/second
Overload Protection Fast-Acting 200mA/250V Fuse
Operating Temperature Range: 32° - 104° F
Display LCD
Battery One 9 V (included)
Page 7For technical questions, please call 1-888-866-5797.Item 37772 61593
SAFETYOPERATIONMAINTENANCE SETUP
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Tool Set Up
1. There are different functions
and 30 ranges provided. A
rotary switch is used to select
functions as well as ranges.
2. A Power Button is used to
turn the meter on or off.
3. A push - push switch (push ON,
push OFF) is used to hold data.
This switch can be used with all
available settings, including DCV,
ACV, DCA, ACA, Hz, and C.
4. As a general rule, the LCD display
box is locked. To adjust the angle
of the display, pull on the top
of the meter and rotate it.
5. This meter has four input jacks that
are protected against overload to
the limits shown. Depending on the
intended function, connect either the
black or red test lead to the COM jack.
6. WARNING! Before attempting to insert
a transistor’s capacitor thermocouple
for testing, disconnect the Test Leads
from all measurement circuits.
7. WARNING! Before taking voltage
measurements with Test Leads,
remove the thermocouple. Do
not connect Test Leads to the
hFE or capacitor socket.
Function Red Lead Connection Input Limits
200mV & 200mV~
V/Ω or V/Ω/Hz
250Vdc or rms ac
V & V~
V/Ω or V/Ω/Hz
1000Vdc, 700Vac (sine)
,
V/Ω or V/Ω/Hz
250Vdc or rms ac
Hz
V/Ω or V/Ω/Hz
250Vdc or rms ac
Ω V/Ω or V/Ω/Hz
250Vdc or rms ac
(μA) mA & (μA) mA~
mA 200mAdc or rms ac
2A & 2A~ A 2Adc or rms ac
20A & 20A~ 20A
10A dc or rms ac continuous
20A for 15 seconds maximum
Additional Multimeter Precautions
1. Do not test voltage on AC
circuits higher than 700 volts.
2. Do not test voltage on DC circuits
higher than 1000 volts.
3. Do not test current on circuits
higher than 20 amps.
4. Be careful not to apply voltage to the
Test Leads when they are connected
to the COM and VΩmA Jacks or when
the Multimeter is in an Ohms testing
setting. Damage can occur to the
multimeter and the fuse may blow.
5. Do not switch between testing
modes with the multimeter
connected to a circuit.
Page 8 For technical questions, please call 1-888-866-5797. Item 37772 61593
SAFETY OPERATION MAINTENANCESETUP
General Operating Instructions
AC Voltage Measurements
Measure AC conductors carrying
up to 700 VAC, 45-450 Hz.
1. Turn the Range Selector Switch to
700 ACV setting. Start with the highest
range if the voltage is unknown.
2. Plug the red lead into the V/Ω/Hz Jack.
Plug the black lead into the COM
Jack. Switch the Multimeter ON.
3. Carefully touch the exposed
conductors with the tips of the probes
to measure the voltage (not amperes).
4. Read measurement. If the voltage is
less than 200 volts, set the Range
Selector Switch to the lower range.
5. When testing is complete, remove
Test Leads and store with multimeter.
DC Voltage Measurements
Measure DC conductors
carrying up to 1000 VDC.
1. Turn the Range Selector Switch
to 1000 DCV setting.
2. Follow the directions above under
“AC Voltage Measurements”, only
use the DC settings instead.
AC Current Measurements
Measure AC conductors carrying
up to 20 amperes.
1. Turn the Range Selector Switch to the
20A~ position. Start with the highest
range if the amperage is unknown.
2. Plug the red lead into the 20A
Jack. (For current under 20A, plug
the red lead into the mA Jack.)
Plug the black lead into the COM
Jack. Switch the Multimeter ON.
3. Carefully touch the exposed
conductors with the tips of the
probes to measure the amperage.
Note: Amperage is always tested in
series with the circuit under test.
4. Read measurement. If the reading is
less than 0.2 amps, switch the red lead
to the VΩmA Jack and set the Range
Selector Switch to the 200 mA setting.
5. When testing is complete, remove
Test Leads and store with multimeter.
DC Current Measurements
Measure DC conductors
carrying up to 20 amperes.
1. Turn the Range Selector Switch to the
20A position. Start with the highest
range if the amperage is unknown.
2. Follow the directions above under
“AC Current Measurements”, only
use the DC settings instead.
Page 9For technical questions, please call 1-888-866-5797.Item 37772 61593
SAFETYOPERATIONMAINTENANCE SETUP
Resistance Measurements
Measure circuit resistance up to 20M Ohms.
WARNING! Do not measure resistance
on circuit with voltage running through it.
Notice: When measuring Ohms,
start with the lowest range if the
resistance is unknown.
1. Turn the Range Selector Switch
to the 200Ω position.
2. Plug the red Test Lead into the V/Ω/
Hz Jack. Plug the black Test Lead into
the COM Jack. Switch the Multimeter
ON. Short the Test Leads together.
The meter should read “0” Ohms.
3. Touch the exposed conductors
with the tips of the Test Leads.
4. Read measurement. If the reading is
“1”, set the Range Selector Switch to
the next higher Ohm (Ω) position.
5. When measuring resistance above 1
MΩ, the meter may take a few seconds
to give a stable reading. This is normal
for high resistance measurements.
6. At the 20MΩ range, the display reading
will be around 0.1 counts over the
actual measurement. These counts
should be subtracted from the resulting
reading. For example, when measuring
10 MΩ resistance, the display will read
10.1, but the correct measurement
should be 10.1-0.1=10.0MΩ
7. Remove and store Test Leads.
Capacitance Measurements
Measure capacitance up to 20μF.
1. Turn the Range Selector Switch to the
20μF position. Start with the highest
range if the capacitance is unknown.
WARNING! Fully discharge
capacitor before measuring.
2. Plug capacitor into the
capacitance testing socket (Cx).
Switch the Multimeter ON.
3. Read measurement. If the reading
is less than 20μF, set the Range
Selector Switch to a lower range.
WARNING! Avoid electric shock.
Remove capacitor before switching
between testing modes.
Frequency Measurements
Measure frequency up to 20kHz.
1. Turn the Range Selector Switch
to the 20kHz position.
2. Plug the red Test Lead into the V/Ω/Hz
Jack. Plug the black Test Lead into the
COM Jack. Switch the Multimeter ON.
Note: Reading is possible at input
voltages above 10Vrms, but the
accuracy is not guaranteed.
Note: In noisy enviroments, use a shield
cable to measure smaller signals.
3. Remove and store Test Leads.
Page 10 For technical questions, please call 1-888-866-5797. Item 37772 61593
SAFETY OPERATION MAINTENANCESETUP
Transistor (hFE) Measurements
Test transistors to ensure proper function.
1. Turn the Range Selector Switch
to the hFE position. Switch
the Multimeter ON.
2. Insert transistor pins into the
appropriate holes of the hFE
testing socket (NPN or PNP)
according to the EBC (Emitter,
Base, Collector) sequence.
3. The meter will show the approximate
hFE value at the test condition of
base current 10μA and Vce 3.2V.
4. Remove and store Transistor.
Diode Measurement
Test the voltage drop in diodes.
1. Turn the Range Selector Switch
to the Diode ( ) position.
2. Plug the red Test Lead into the V/Ω/Hz
Jack. Plug the black Test Lead into the
COM Jack. Switch the Multimeter ON.
3. Connect red probe to the anode of the
diode and the black to the cathode.
4. The approximate forward voltage
drop of the diode will be displayed
in mV. If the connection is
reversed, only “1” will be shown.
5. Remove and store Test Leads.
Continuity Measurement
Test continuity between two
points of a circuit.
1. Turn the Range Selector Switch
to the position. Switch
the Multimeter ON.
2. Connect Test Leads to two points
of the circuit. If continuity exists
(i.e., resistance is less than
50Ω), a buzzer will sound.
3. Remove and store Test Leads.
Temperature Measurement
1. Turn the Range Selector Switch
to the TEMP position. Switch the
Multimeter ON. Display will show
the current ambient temperature.
2. Plug a “K”-type thermocouple into
the temperature measuring socket.
3. Contact object to be measured
with the thermocouple probe.
Read measurement.
WARNING! Avoid electric shock.
Remove thermocouple before
switching between testing modes.
Page 11For technical questions, please call 1-888-866-5797.Item 37772 61593
SAFETYOPERATIONMAINTENANCE SETUP
Maintenance and Servicing
Procedures not specifically explained in this manual
must be performed only by a qualified technician.
Cleaning, Maintenance, and Lubrication
1. Wipe unit with a dry, lint-free cloth.
Do not use solvents or abrasives.
2. Remove battery if not in
use for long periods.
3. Store unit in a dry location.
4. Other than the battery and fuse,
there are no replaceable parts
on this unit. Repairs should be
done by a qualified technician.
Battery/Fuse Replacement
If the sign “ ” appears on the LCD
display, the battery should be replaced.
1. Remove the Test Leads
from the multimeter.
2. Turn the unit over.
3. Remove screws.
4. Remove back cover carefully.
There may be wires attached.
5. Pull battery/fuse out of unit and
replace with the same. (9V battery
or F 2A/250V (quick acting) fuse)
6. Replace cover and retighten screws.
Record Serial Number Here:
Note: If product has no serial number,
record month and year of purchase instead.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

CEN-TECH 37772 Owner's manual

Category
Multimeters
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI