CEN-TECH 95342 Assembly And Operation Instructions Manual

Brand: CEN-TECH

Model: 95342

Type: Assembly And Operation Instructions Manual

DIGITAL PEN STYLE

MULTIMETER

Model

95342

ASSEMBLY AND OPERATION INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2007 by Harbor Freight Tools

or any artwork contained herein may be reproduced in any shape or form without the

express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 95342 For technical questions please call 1-800-444-3353. Page 2

SPECIFICATIONS

Material ABS housing with LCD screen

Lead 29” lead with 5 7/8” Tip Probe

Maximum Input 600 VAC/600 VDC

Battery 3 V, CR2032 (included)

Fuse F250mA250V (Fast-acting 250 mA, 250 V) (Fast-acting 250 mA, 250 V)

Meter Functions AC/DC voltage, AC/DC current, resistance measurement,

diode/continuity testing

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instruc-

tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with

this manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

SAFETY WARNINGS AND PRECAUTIONS

WARNING: When using tool, basic safety precautions should always be followed to reduce

the risk of personal injury and damage to equipment.

Read all instructions before using this product!

In this manual:

WARNING indicates a potentially hazardous situation which, if not avoided, could result

in death or serious personal injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in

a minor/moderate personal injury or damage to this tool or the unit being tested by it.

Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

Keep children away while operating the Digital Multimeter. Keep children out of

the work area. Not a toy. Keep away from children.

Stay alert. Do not operate the Digital Multimeter while tired or under the inﬂuence of

drugs, alcohol, or medication.

Use the correct tool for your application. Do not use it for applications other than

intended.

Maintain the Digital Multimeter with care. Do not use a damaged Digital Multimeter.

Tag a damaged Digital Multimeter “Do not use” until repaired.

Multimeter service must be performed only by qualiﬁed repair personnel. Service

or maintenance performed by unqualiﬁed personnel could result in a risk of injury.

REV 07k

SKU 95342 For technical questions please call 1-800-444-3353. Page 3

Use eye and ear protection. Always wear ANSI-approved impact safety goggles and

work gloves.

Avoid working alone. If an accident happens, an assistant can bring help.

Avoid electrical shock. Use extreme caution when testing uninsulated conductors

or bus bars. Prevent body contact with grounded surfaces such as pipes, radiators,

ranges and cabinet enclosures when testing.

Maintain tools with care. Inspect the Multimeter before use. Make certain that

the Multimeter has a fresh battery. Pay special attention to the insulation protecting

the probes and lead.

Do not use the Multimeter if:

The test leads are damaged in any way

The battery is low

Any abnormal operation is detected (if in doubt about the condition of the Multimeter,

have it serviced)

The battery cover is open.

Check the leads for exposed metal, damaged insulation, and continuity. Replace

damaged test leads immediately, before use.

Do not test voltage on circuits higher than 600 volts AC or 600 volts DC.

Do not test current on circuits higher than 200 mA (0.2 amps).

Do not expose to rain or wet conditions. Water entering will increase the risk of

electric shock.

Disconnect the multimeter from the power source before making any adjustments,

changing accessories, or storing the tool. Always cap the probe and test lead

before performing any inspection, maintenance, or cleaning procedures. Such

preventive safety measures reduce the risk of electric shock.

Do not operate in explosive atmospheres, such as in the presence of ﬂammable

liquids, gases, or dust. Sparks may ignite the dust or fumes.

Do not switch between testing modes with the Multimeter connected to a cir-

cuit.

Cap the probe and test lead before performing maintenance, opening the case,

or the battery compartment.

SAFETY PRECAUTIONS

Use caution when working near voltages above 30 VAC rms, 42 VAC peak, or 60

VDC. Voltages this high present a risk of electric shock.

Disconnect the circuit’s power before connecting the meter in series, when mea-

suring current.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

SKU 95342 For technical questions please call 1-800-444-3353. Page 4

Connect the common (COM) test lead ﬁrst and disconnect it last.

Hold the probes with ﬁngers behind guards.

CAUTION

Prior to testing resistance, diodes, or continuity; disconnect all power to the

circuit and discharge all high-voltage capacitors.

Check fuse before testing current.

Use the proper settings, terminals, techniques, and range for the tests performed.

Always start with the range stated in the instructions.

Warning: The warnings, cautions, and instructions discussed in this instruction manual can-

not cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built into

this product, but must be supplied by the operator.

UNPACKING

When unpacking, check to make sure that the Digital Multimeter is intact and undam-

aged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown

on the cover of this manual as soon as possible.

FUNCTIONS

Pen Light Hold Mode On/Off/Function

Input

Probe

Test

Lead

Figure 1

Input probe and test lead

The Digital Multimeter has both an Input Probe and a Test Lead. The Input Probe is used

for positive polarity and is used when testing voltage, resistance, current and diode. The

Test Lead is used for negative polarity.

Hold button

Optionally, press the Hold button to keep the display reading the same after the leads

have been removed from the conductors. Press and release the Hold button again to resume

normal operation.

REV 07k

SKU 95342 For technical questions please call 1-800-444-3353. Page 5

OPERATION INSTRUCTIONS

Testing Voltage (AC/DC)

Use the Mode Button to select the “V” setting. With the circuit on, carefully touch the

probe (positive polarity) and test leads (negative polarity) to the exposed conductors

with the tips to measure the voltage (not amperes).

The Multimeter will give you a reading in the LCD display.

Testing Resistance

Warning: Never measure resistance on a circuit with voltage running through it.

Set the Mode Button to the Ohm (W) setting.

Touch the Test Lead and Probe together. The meter should read “0” Ohms. The continu-

ity test is done to determine if the circuit is open or closed. Unplug the product being

tested prior to using the Multimeter on the product.

While the test leads are not touching anything, the Multimeter LCD readout will show a

reading of inﬁnity. This indicates an open circuit that can not conduct current. Touching

probe and test lead together will change the reading to zero. This indicates that the

circuit is closed and can conduct current.

Touch the exposed conductors with the tips of the Test Lead and Probe.

Read measurement in Ohms. If the reading is zero and the tone sounds then there is

continuity between the two conductors.

Diode Test

Use the same steps as “Measuring Resistance.” Connect the Probe to the positive pole

of the diode, and the Test Lead to the negative pole of the diode.

Read the forward resistance on the LCD readout.

DC Current Measurements

Set the Mode Button to the Current (mA) position. Disconnect power to the circuit.

WARNING: This Meter is designed only for small scale amperage testing. Do not use

unless you are certain that the voltage is under 600 V and that the amperage is under

200 mA (milliamps) or 0.2 amps.

Carefully connect the two probes inline with the circuit, so that the current must pass

through the meter.

WARNING! Keep ﬁngers and all conductive materials clear from the metal parts of

the probes. Connect power and read measurement. Carefully disconnect power and

disconnect meter from circuit.

SKU 95342 For technical questions please call 1-800-444-3353. Page 6

Operating the Pen Light

Press the “Pen Light” button to turn on the Pen Light. This will shine a light from the

front end of the Multimeter, allowing you to see the Probe end of the Multimeter.

TROUBLESHOOTING

Multimeter does not turn On or Off.

Make certain Power button is ON.

Check battery.

Check that battery is installed correctly.

Probe and leads do not give feedback.

Make certain Power button is ON.

Check battery.

Check that battery is installed correctly.

Probe and Lead reading is not reasonable

Verify that Probe is not touching Lead

Verify that Probe (positive) and Lead (negative) are correctly touching connec-

tions.

MAINTENANCE

Protect the Digital Multimeter from rough use. It is susceptible to damage from being

dropped, struck, improperly mounted or other abuse. The precision movement is similar

to a watch works, and should be treated accordingly.

Protect the Multimeter from exposure to water or corrosive materials. It should be

kept clean and dry. Occasional cleaning with a clean rag will extend its life and good

appearance.

Store in a dry location to inhibit rust. Keep out of the reach of children.

Replacing the battery

Remove the battery cover by gently sliding it off.

Replace the battery with the type speciﬁed. Insert it into the compartment so the

positive and negative polarity match those indicated.

Insert the ends of the Battery Cover back over the battery compartment then slide

it into place.

Dispose of the old battery in accordance with local ordinances for proper dispos-

al.

Replacement parts are not available for this product.

SKU 95342 For technical questions please call 1-800-444-3353. Page 7

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase. This

warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or

accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, in-

juries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to

you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the complaint

must accompany the merchandise. If our inspection veriﬁes the defect, we will either repair or

replace the product at our election or we may elect to refund the purchase price if we cannot

readily and quickly provide you with a replacement. We will return repaired products at our

expense, but if we determine there is no defect, or that the defect resulted from causes not

within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you speciﬁc legal rights and you may also have other rights which

vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

REV 07k

CEN-TECH 95342 Assembly And Operation Instructions Manual

CEN-TECH 95342 Assembly And Operation Instructions Manual

CEN-TECH 95342 Assembly And Operation Instructions Manual

Related papers

Other documents