Messoa SDS730PRO Quick start guide

Messoa
Brand
Messoa
Model
SDS730PRO
Category
Security camera accessories
Type
Quick start guide

This manual is also suitable for

Speed Dome Camera
Quick Installation Guide
Before attempting to connect or operate this product, please read these instructions
carefully and save this manual for future use.
CONTENTS
INSTRUCTION ..................................................................
INSTALLATION INSTRUCTIONS.........................................
CONNTCTION & APPLICATIONS.........................................
MENU SCREEN
................................................................
SDS710Pro_SDS730Pro_SDS750Pro
ZEIM-4000605G A.1
2
3
4
5
A. Exterior
B. Main cablin
Note: Speed dome does not supported WAN,
LAN, or the Reset function.
Instructions
This Installation Guide includes important information for unit
installation. Please carefully read through this manual for proper
installation instructions to ensure a quality installation.
Please refer to gure A and B.
1. Upper case
2. Main signal connector
3. External body
4. Safety wire
5. Address / baud rate /
termination resistor switch
Package Contents
Major Components
• Main Unit
• Instruction Manual
• Quick Installation Guide
• Screws and wire accessories
pack
• Power Adapter
2
Power Cable
Black-AC24V+
White-AC24V-
Green-GND
AC 24V Power In
RS485 Signal Cable
Optical Dome
Connector Ring
WAN
Video Out
Alarm In
Alarm Out
Safety Cable
Main Unit
Lower lid
Reset
LAN
3
Installation Instructions
1. Before icking on the switch, the
upper case should be separated
from the external body (Figure A).
Then the appropriate communication
protocol, baud rate, and machine
address should be chosen. For
details please refer to the Instruction
Manual.
2. During installation, the Safety wire
should be secured to prevent the
unit from dropping. After conrming
the safety mechanism, the following
installation procedure may begin
(Figure A).
3. When combining the upper case
and external body, rst align the
screw holes to the body screw rods.
Rotate to align both arrows ( )
as in (Figure B), and then lock the
external body to the upper case with
screws.
4. Connect the video signal: Use the
coaxial cable to connect BNC video
output to the monitor input terminal
(Figure B).
5. Connect through RS485 interface:
Connect the Data+/Data- wires to
RS485 port on keypad controller
(Figure B).
6. Connect the alarm signal: This unit
provides 6 alarm inputs and 1 alarm
output (Figure B).
7. When performing indoor and outdoor
installation, please select appropriate
accessories from (Figure D) and
refer to the instruction manual for
installation details to ensure a quality
installation.
8. Connect to power: This unit can only
accept AC 24V±10% power. Damage
may result if inappropriate power is
supplied.
*Please contact your supplier for adequate control
panel. Improper control panel might cause damage
for speed dome.
Speed Dome
A larm O ut
C lo se (Pink )
A larm O ut C o m (L ig ht Blue )
A larm O ut O pe n (W hite)
A larm In 3 ( O ra ng e)
A C 2 4V P ow er a dapter
M on itor
K eypa d c ontroller
LA N
W A N
R S4 85
R ese t
C onv erte r
A larm in
A larm O ut
G N D (G rey )
G N D (P urple)
G N D (B la ck)
A larm In 6 ( Blue)
A larm In 5 ( G re en )
A larm In 4 ( Ye llow )
A larm In 2 ( Red)
A larm In 1 ( Bro w n)
D a ta + (O ra n ge )
D at a - (Wh it e )
A C+ (Black)
A C- (White )
4
Through the keypad controller (Figure C) RS485 interface, the
camera can be controlled and parameters can be congured.
Connection
C. Connection diagram
Applications
D. Applications
Pendant pipe mount
Wall mount
Wall mount with
junction box
Parapet
wall mount
Pendant pipe mount
with junction box
Pole mount
Corner mount
RS485
KEYPAD CONTROLLER
5
Start
During startup, the camera will
rst perform a series of self-
testing and default scanning
before returning to the original
position. During this time,
the screen will show basic
information on the unit software
version,communication protocol,
unit address, and baud rate (as
indicated below).
VER:
PROTOCOL:
ADDRESS:
BAUD RATE:
Operation
After startup, the keypad controller can be used to control the
camera movements such as pan/tilt movement and zooming etc.
The default hotkeys (listed below) with the OSD menu can be used
to perform various function settings.
Menu Screen
Press 95 and hold keys
for 2 seconds to access the
OSD menu. Most of the camera
related functions such as pan/tilt
movement, scanning, and other
default position settings have to
be congured through the OSD
menu. For detailed operation
method, please refer to the
instruction manual.
Default Commands (For keypad controller with Messoa-P, Messoa-D, Pelco P, Pelco D, Bosch,
Ernitec protocol only)
Buttons Function Buttons Function
1~32, 35~66,
111~255+Preset
33+Preset
34+Preset
70+Preset
90+Preset
91+Preset
92+Preset
71+Preset
72+Preset
73+Preset
74+Preset
75+Preset
76+Preset
88+Preset
89+Preset
96+Preset
97+Preset
98+Preset
Move camera to Preset position
1~32, 35~66, 111~255
Flip
Return to original position
Begin auto patrol - Group 1
Begin auto patrol - Group 2
Begin auto patrol - Group 3
Begin auto patrol - Group 4
Backlight compensation ON
Backlight compensation OFF
White balance - one push
Focus - one push
Show software version
Self-test
Color mode (daytime)
Monochrome mode (nighttime)
Stop scanning
Begin random scan
Begin frame scan
99+Preset
101+Preset
102+Preset
103+Preset
104+Preset
105+Preset
1~32, 35~66, 111~255+Set
Preset
83+Set Preset
90+Set Preset
91+Set Preset
92+Set Preset
93+Set Preset
95+Set Preset
101+Set Preset
102+Set Preset
103+Set Preset
104+Set Preset
Begin auto scan
Run pattern tour - Group 1
Run pattern tour - Group 2
Run pattern tour - Group 3
Run pattern tour - Group 4
Stop pattern tour record
Set Preset position 1~32,
35~66, 111~255
Enter privacy zone setup mode
Set manual left limit
Set manual right limit
Set scan left limit
Set scan right limit
Open OSD menu
Start pattern record - Group 1
Start pattern record - Group 2
Start pattern record - Group 3
Start pattern record - Group 4
Instructions:
+ Preset: Press key once,
+ Set Preset: Press and hold the key for 2 seconds
*123+preset unavailable*
Default Commands (For keypad controller with GE(Kalatel)protocol only)
Buttons Function Buttons Function
1~32, 35~52 +Preset
33+Preset
34+Preset
62+Preset
61+Preset
60+Preset
59+Preset
63+Preset
58+Preset
57+Preset
56+Preset
Move camera to Preset position
1~32, 35~52
Flip
Return to original position
Begin frame scan
Begin random scan
Stop scanning
Begin auto patrol
Begin auto scan
Show software version
Self-test
Focus - one push
55+Preset
54+Preset
53+Preset
1~32, 35~52 +Set Preset
62+Set Preset
61+Set Preset
60+Set Preset
59+Set Preset
63+Set Preset
White Balance - one push
Backlight compensation OFF
Backlight compensation ON
Set Preset position 1~32,35~52
Set manual left limit
Set manual right limit
Set scan left limit
Set scan right limit
Open OSD Menu
*Please see manual for DVR with Tyco Protocol ONLY*
6
■ Note:
Before installation, the lens cap and
lens protection plate have to be
removed.Then, lock the optical dome and
exterior body securely.
■ Warning:
To prevent electric shock, please do
not remove the exterior body. Do not
attempt to disassemble. Repairs should be
attempted only by qualied personnel.
SW1 / SW2 Switch Denition
1 2 3 4 5 6 7 8 Denition
ON OFF OFF OFF OFF OFF OFF 1
OFF ON OFF OFF OFF OFF OFF OFF 2
OFF ON ON ON ON ON ON ON 254
ON ON ON ON ON ON ON ON 255
SW1 camera address denition
OFF
ON
1 2 3 4 5 6 7 8
7
Power cable denition
Color denition
Black AC 24V+
White AC 24V-
Green GND
NC
1 2 3 4 5 6 7 8
ON NC termination res on
OFF NC termination res off
OFF OFF OFF OFF NC NC Messoa-P
ON OFF OFF OFF NC NC Messoa-D
OFF ON OFF OFF NC NC Pelco-P
ON ON OFF OFF NC NC Pelco-D
OFF OFF ON OFF NC NC Bosch
ON OFF ON OFF NC NC Ernitec
OFF ON ON OFF NC NC Kalatel
ON ON ON OFF NC NC Tyco
OFF OFF 19200
ON OFF 9600
OFF ON 4800
ON ON 2400
NC
NC
NC
NC
NC
NC
NC
NC
8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Messoa SDS730PRO Quick start guide

Messoa
Brand
Messoa
Model
SDS730PRO
Category
Security camera accessories
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents