Honeywell 805595 User manual

Brand: Honeywell

Model: 805595

Category: Fire protection

Type: User manual

798941

Technische Änderungen vorbehalten!

10.2006

G 205113

Technical changes reserved!

Bedienungs- und Installationsanleitung

Operation and Installation Instruction

IQ8Wireless Funkkoppler für Wandmontage

IQ8Wireless transponder for wall mounting

(Art.-Nr. / Part No. 805595)

Page is loading ...

798941

10.2006

G 205113 Technical changes reserved!

Operation and Installation Instruction

IQ8Wireless transponder for wall mounting

(Part No. 805595)

IQ8Wireless transponder for wall mounting

24 FB 798941 / 10.06

Intended purpose

This product must only be used for the applications outlined in the catalogue and the

technical description and in combination with external components and systems which

have been approved or recommended by the manufacture.

Warning

In order to ensure correct and safe operation of the product, all guidelines concerning its

transport, storage, installation, and mounting must be observed. This includes the

necessary care in operating the product.

Safety-relevant user information

This manual includes all information required for the proper use of the products described.

The term 'qualified personnel' in the context of the safety information included in this

manual or on the product itself designates:

• project engineers who are familiar with the safety guidelines concerning fire alarm and

extinguishing systems.

• trained service engineers who are familiar with the components of fire alarm and

extinguishing systems and the information on their operation as included in this manual.

• trained installation or service personnel with the necessary qualification for carrying out

repairs on fire alarm and extinguishing systems or who are authorised to operate, ground

and label electrical circuits and/or safety equipment/systems.

Safety warnings

The following information is given in the interest of your personal safety and to prevent

damage to the product described in this manual and all equipment connected to it.

Safety information and warnings for the prevention of dangers putting at risk the life and

health of user and maintenance personnel as well as causing damage to the equipment

itself are marked by the following pictograms. Within the context of this manual, these

pictograms have the following meanings:

Designates risks for man and/or machine. Non-compliance will create risks

to man and/or machine. The level of risk is indicated by the word of warning:

Important information on a topic or a procedure and other important

information!

This is an important guideline issued by VdS Schadenverhütung GmbH,

Cologne. If the hazard alarm system is programmed in compliance with VdS,

this section must be read very carefully and all instructions must be adhered to.

Disassembling

In accordance with the regulations 2002/96/EG (WEEE), after being

disassembled, electrical and electronic equipment is taken back by the

manufacturer for a proper disposal.

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 25

Table of contents Page

General.................................................................................................................................................26

8 System design information .................................................................................................................27

9 Assembly..............................................................................................................................................30

10 Installation.......................................................................................................................................32

10.1 Connecting the power supply..............................................................................................32

10.2 Operation as a device on the analog loop.........................................................................33

10.3 Operation on a conventional detector zone.......................................................................34

10.3.1 Connection of two detector zones for individual fire and fault alarm .............35

10.4 Stand-alone operation.........................................................................................................36

10.5 Relay outputs........................................................................................................................37

10.6 Inputs.....................................................................................................................................38

10.6.1 R - input .........................................................................................................38

10.6.2 P - terminal.....................................................................................................38

10.6.3 Interface (Schnittstelle)..................................................................................38

10.6.4 Input (Eing) ....................................................................................................38

10.6.5 U

...................................................................................................................38

11 Commissioning...............................................................................................................................39

11.1 Analog loop...........................................................................................................................40

11.2 Conventional detector zone input.......................................................................................41

11.3 Important battery information..............................................................................................42

12 Specifications..................................................................................................................................44

If used properly, the “IQ8Wireless transponder (Part No. 805595)“ complies with

the basic directives and corresponding requirements in according to the R&TTE

Directive 1999/5/EC.

The EC conformity statement can be downloaded at www.novar.de.

Additional and updated Informations

The described features, specifications and product related informations in this

manual correspond to the date of issue (refer to date on the front page) and may

differ due to modifications and/or amended Standards and Regulations of the

System design, Installation and Commissioning.

Updated documentations and informations are available for comparison on the

www.novar.de homepage.

EU-Community requirements

This RF-device has been developed, manufactured and labeled in accordance to

the requirements of the European Union (EU). If this device should be installed

outside this EU directives and respectively in Italy (I), Norway (N), Cyprus (CY),

Poland (PL), Slovakia (SK), Croatia (HR) or Romania (RO), the valid standards

and requirements of the appropriate country must be observed and satisfied.

Commissioning of this device is only permitted in accordance to the national and

local standards and requirements.

IQ8Wireless transponder for wall mounting

26 FB 798941 / 10.06

7 General

The IQ8Wireless transponder, in combination with the associated IQ8Wireless detector bases

(Part No. 805593) and IQ8Wireless interfaces enables the wireless connection of IQ8Quad

series fire detectors and may be used as a device on the analog loop of the IQ8Control fire

alarm system or as a stand-alone wireless control device in fire alarm systems with

conventional detector zones.

The IQ8Wireless system guarantees adequate protection against electro-magnetic

interference under normal ambient conditions. This module generates and uses electro-

magnetic radiation and may disturb other wireless transmissions if it is not used as intended or

not installed as described in the instructions. In principle, electro-magnetic influence of

equipment cannot be excluded for all installations. If this module causes electro-magnetic

interference on radios or televisions that cannot be rectified by switching the device on and off,

the following measures can be carried out to rectify the interference:

• Change the position of the wireless components

• Create a greater gap between the module which is exhibiting signs of interference and the

wireless components

System requirements

• Programming software tools 8000 from Version V1.09

• To operate the IQ8Wireless transponder as a loop device of the Fire Alarm Control

System IQ8Control, the IQ8Control operating system software Version V3.04 R001 is

required.

Accessories

Part No. Description

805593

IQ8Wireless detector base for automatic Fire detectors series IQ8Quad

(without integrated alarm device)

805594

IQ8Wireless Gateway automatic Fire detectors IQ8Quad

805597 4 Lithium batteries (type AA / 3,6V) for power supply

805601

IQ8Wireless universal Interface (red), without cover

805602

IQ8Wireless universal Interface (white), without cover

805603

IQ8Wireless Mounting frame for Alarm device IQ8Alarm (red + white)

805604

IQ8Wireless Mounting frame for automatic Fire detectors IQ8Quad (white)

805605

Cover for IQ8Wireless Interface 805601 und 805602 (red + white)

For the operation of the intelligent Fire alarm detectors series IQ8Quad with

integrated alarm device use Part No. 805602 and 805604.

Warranty claims will not be accepted in case of damage caused by

non-compliance with the operating instructions. The manufacturer is not liable for

subsequent damage resulting from the above. Please study the installation

instruction of the IQ8Wireless transponder carefully before installing.

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 27

8 System design information

When fire alarm systems are planned and installed in the Federal Republic of Germany,

they must comply with certain standards and guidelines, including the following:

• DIN VDE 0100

• DIN 14675

• DIN VDE 0833

• DIN EN54

• VdS Guidelines (VdS Schadenverhütung GmbH, Cologne)

• Local building authority conditions

In principle, these requirements and specifications should also be complied with in the

planning of fire alarm systems outside the area of validity of these standards and guidelines.

Depending on the actual area in which the system will be used, additional national conditions

and regulations may have to be complied with.

Key data for the IQ8Wireless transponder:

• Max. 32 IQ8Wireless detector bases (incl. IQ8Quad fire detector) per transponder or

• Maximum 10 IQ8Wireless MCPs (incl. IQ8Wireless Interface) per transponder.

• If the IQ8Wireless transponder is connected to a conventional detector zone, all assigned

IQ8Wireless devices form one common detector zone (refer to VdS Guidelines)

Key data for the analog loop (fire alarm system IQ8Control)

• An IQ8Wireless transponder is a device on the analog loop and requires 1 address

• An assigned IQ8Wireless detector base (incl. IQ8Quad fire detector) requires 1 address

• An IQ8Wireless MCP (incl. IQ8Wireless Interface) requires 1 address

• Max. 127 devices (addresses) per analog loop

• Max. 10 IQ8Wireless transponders per analog loop

• Max. 20 IQ8Wireless transponders per fire alarm control panel IQ8Control C

• Max. 50 IQ8Wireless transponders per fire alarm control panel IQ8Control M

•

Every automatic IQ8Quad fire detector (with IQ8Wireless detector base) or IQ8Wireless

MCP (incl. IQ8Wireless Interface) can be configured as a separate detector zone

Automatic fire detectors and MCPs may not be operated on one and the same

IQ8Wireless transponder.

IQ8Wireless transponder for wall mounting

28 FB 798941 / 10.06

The installation location of the IQ8Wireless transponder should be chosen so that the shortest

transmission path (wireless path) to the wireless bases can be implemented and that no

electro-magnetic interference is to be expected. The function of the IQ8Wireless transponder

may be seriously affected and its range reduced by interference sources or an unsuitable

installation location:

Electrical interference sources

• Energy/power cables

• Powerful wireless transmitters in the vicinity

• Switched-mode electronic circuits

• Computer and IT systems

Mechanical interference sources

• Metal grating and metal gates

• Metal cabinets (cabinet units)

• Concrete ceilings and concrete walls

• Unfavourable arrangements (angles) of IQ8Wireless transponders and IQ8Wireless

detector bases

The IQ8Wireless transponder operates with a range up to 25 channels within the

frequency band of 433 MHz and 868 MHz.

Also consider temporary interference sources such as mobile phones or

computers!

Requirements for the environment

• The quality of the wireless transmission depends very much on the ambient temperature.

A reduction in temperature in the monitored rooms, for example at night may have a

negative effect on the wireless quality achieved during the day.

• Sliding gates or doors which are open during the day for operational reasons as well as

overhead cranes may disrupt the wireless path when they are closed or in a different

position respectively.

To plan the wireless system the tools 8000 software contains a field strength

measurement tool. This can be used to check the quality of the wireless link

(field strength) between the IQ8Wireless transponder and the IQ8Wireless

devices.

If used properly, the “IQ8Wireless transponder (Part No. 805595)“ complies with

the basic directives and corresponding requirements in according to the

R&TTE Directive 1999/5/EC.

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 29

Weakening of the wireless signal

Metal, metal grating, aluminium lining

-90% to -100%

Reinforced concrete wall

-30% to -90%

Brick (or insulated partition walls)

-5% to -35%

max. 300m*

0% to -10%

Timber, plasterboard, leight-weight partition walls

Fig. 14: Weakening of the wireless signal in case of mechanical obstructions

(as a percentage)

* Maximum range with line of sight between the IQ8Wireless detector base and the

IQ8Wireless transponder as well as optimum technical conditions.

IQ8Wireless transponder for wall mounting

30 FB 798941 / 10.06

9 Assembly

The IQ8Wireless transponder should be installed with suitable fixing material (such as wall

plugs and screws) in the proper position on a stable wall surface with no mechanical stress of

the housing. The mounting place location of the IQ8Wireless transponder should be chosen so

that a good wireless link (field strength) between the transponder and the assigned

IQ8Wireless detector bases is guaranteed. The transmission quality can be checked with the

programming software tools 8000 version V1.09 or higher.

172

120

Top

Fig. 15: Fixing points on the back of the housing (sizes in mm)

On the front side of the housing there are 4 LED status indicators, each with its own inscription

field, as well as the housing screw.

LED 1

LED 2

LED 3

LED 4

200

280

Top

144

red green

Fig. 16:IQ8Wireless transponder in housing with display LED and aerials (sizes in mm)

Observe that the IQ8Wireless transponder must not be installed on walls with

metal grating or which are filled with aluminium foil-insulated glass wool and

which could thus seriously affect the wireless communication.

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 31

LED 1

Operation (green)

Lits in normal operation

LED 2

Common fire alarm (red)

Lits when the fire alarm of an assigned wireless device has been detected.

The relay >common fire alarm< is activated.

LED 3

Common trouble (yellow), display not latched

Lits when a fault message from the IQ8Wireless transponder or an assigned

wireless device has been detected. Activation of the >common fault< relay is

interrupted and the relay contact changes position.

LED 4

Initialisation (yellow)

Lits during the switch-on/learning process of the IQ8Wireless transponder while the

wireless devices are being recognised.

Housing screw to open/close the transponder housing

LED-indicators on the board

Status indication of the Analog loop communication

Both LED (red and green) twinkle while the data communication on the connected

loop of the FACP IQ8Control is active.

red green

LED-incicator for the wireless operation mode

Off

flashes

(2Hz)

Normal operation mode

All assigned wireless devices operates as required in

the frequenzy-hopping mode.

flashes

(2Hz)

Normal operation with a communication fault

At least one wireless device is out of the frequenzy-

hopping mode and is automatically searched in the

base channel. This fault is indicated at the FACP

after approx. 40-60s. If the wireless device could be

automatically found within this time the red LED goes

out.

Flashes alternately

(2Hz)

Installation mode (restricted operation)

e.g. during field strength measurement, transponder

or detector data assignment or while searching a

wireless device.

Flashes common

(2Hz)

Malfunction – Wireless mode disabled

Wireless communication not possible Î transponder

is defect (return to factory)

Flashes common

each 7 seconds

Disablement – wireless mode off

The wireless operation mode is automatically

disabled due to no wireless is assigned or present.

IQ8Wireless transponder for wall mounting

32 FB 798941 / 10.06

10 Installation

10.1 Connecting the power supply

The power supply can come from the fire alarm control panel or from an external power unit.

To supply power to the IQ8Wireless transponder you must install a separate, protected supply

line. The connection cable must comply with the guidelines relating to the functions of fire

alarm systems. If several IQ8Wireless transponders are connected to a shared power supply,

each power line must be protected individually and non-reactively, for example with the 8-fuse

card (Part No. 382040).

Monitoring the power supply

The external power supply is monitored by the wireless transponder. If the IQ8Wireless

transponder is installed as a device on the analog loop of the IQ8Control fire alarm system,

a fault is transmitted via the loop to the fire alarm control panel where it is displayed.

If you connect the IQ8Wireless transponder to a standard detector zone, the >Common fault

relay< (SaS-Stör) output may be used to report faults.

9 V.....30 V DC

External Power supply

FACP

ext.

GND

ext.

GND

Fault

contact

Fig. 17: Power supply connection

A VdS-approved power unit according to EN54-4 must be connected to supply

power to the IQ8Wireless transponder, e.g. external 12 V DC power unit with

battery compartment (Part No. 785653) or

24 V DC design (Part No. 785655).

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 33

10.2 Operation as a device on the analog loop

The IQ8Wireless transponder is connected directly to the analog loop of the IQ8Control fire

alarm control system.

All reports from the transponder are transmitted via the analog loop to the IQ8Control fire

alarm control panel. The assigned wireless devices can be split into individual detector zones.

If a report is sent from a IQ8Wireless base, the detector zone and detector number of the

IQ8Wireless base (incl. fire detector IQ8Quad) or the wireless manual call point IQ8MCP are

displayed.

The two relay outputs of the transponder can also be used for control functions. An external

power supply is required to operate the transponder.

A+

B+

A-

B-

++--

IN OUT

9 V.....30 V DC

PE PE

++--

IN OUT

9 V.....30 V DC

PE PE

Jumper J1 + J2 removed

Fig. 18: Connecting the IQ8Wireless transponder to the analog loop (schematic diagram)

System requirements:

• Fire alarm control panel IQ8Control C/M with appropriate software version V3.04 R001

• Analog loop module (Part No. 804382 / 784382)

• Programming software tools 8000 version V1.09 or higher

Connection data

• External power supply 9 V DC to 30 V DC

• Jumpers J1 and J2 removed (factory setting)

• Reset time = 0.2 to 3 seconds

IQ8Wireless transponder for wall mounting

34 FB 798941 / 10.06

10.3 Operation on a conventional detector zone

The IQ8Wireless transponder can be connected to the conventional detector zone input of a

fire alarm system via the relays. All IQ8Wireless devices form a common detector zone on this

IQ8Wireless transponder. You cannot split these into several, different detector zones. The

detector zone input is connected with resistor (R1) to the inversely operated >common fault<

relay (Common fault) which is activated in quiescent mode. In case of an alarm the alarm

resistor (R2) is switched parallel to R1 and the detector zone is triggered via the

>common fire alarm< relay (Common fire).

Reset

The IQ8Wireless transponder is reset to the functional, normal status when the voltage of the

detector zone drops below 5V for at least 60ms (e.g. by switching the respective detector zone

e.g. no. 1 on/off). The detector zone can also be reset via an external reset button (refer to c)

or a relay contact. In this case a voltage of 9 to 30 V DC must be switched for at least

1 second at the input (input +/-) of the IQ8Wireless transponder.

9 V - 30 V DC

Reset

Detector zone 1

NONC

NCNO

Eing

PPE

Sa-Feuer

Common fire

Sa-Stör

Common fault

Jumper J1 + J2

inserted

Fig. 19: Connection to a conventional detector zone input (Example)

Connection data

• External power supply 9 V DC to 30 V DC

• Detector zone voltage 9 V DC to 30 V DC

• R1 quiescent resistor (e.g. 10KΩ for conventional detector zones System 8000/IQ8Control)

• R2 alarm resistor (e.g. 1KΩ for conventional detector zones System 8000/IQ8Control)

• Jumpers J1 and J2 inserted (supplied with package)

• Reset time = 0.2 to 3 seconds

Depending on the detector zone input, with this connection a fault in a single

wireless device can lead to a fault in the entire detector zone and affect the

detector function. In this case the fault message can be moved to a separate

detector zone input, so that devices that are not defective remain functional.

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 35

10.3.1 Connection of two detector zones for individual fire and fault alarm

The application provides the separate transmission of a fault alarm (e.g. battery low message)

and an additional fire alarm message. The fault message is non-latching and is resetted

automatically after the cause of the fault alarm is not present anymore.

Reset

The IQ8Wireless transponder is reset to the functional, normal status when the voltage of the

detector zone “Fire” drops below 5V for at least 60ms (e.g. by switching the fire zone on/off).

The detector zone can also be reset via an external reset button (refer to c) or a relay contact.

In this case a voltage of 9 to 30 V DC must be switched for at least 1 second at the input

(input +/-) of the IQ8Wireless transponder.

Detector zone

NONC

NCNO

R P

"Fault"

Detector zone

"Fire"

FACP

10K

R1 R2 R3

Sa-Feuer

Common fire

Sa-Stör

Common fault

Jumper J1 + J2

inserted

9 V - 30 V DC

Reset

Eing

Fig. 20: Wiring of two individual detector zones for fire alarm and fault (Example)

Connection data

• External power supply 9 V DC to 30 V DC

• Detector zone voltage 9 V DC to 30 V DC

• R1 quiescent resistor (e.g. 10KΩ for conventional detector zones System 8000/IQ8Control)

• R2 alarm resistor (e.g. 1KΩ for conventional detector zones System 8000/IQ8Control)

• R3 fault resistor (e.g. 10KΩ for conventional detector zones System 8000/IQ8Control)

• Jumpers J1 and J2 inserted (supplied with package)

• Reset time = 0.2 to 3 seconds

IQ8Wireless transponder for wall mounting

36 FB 798941 / 10.06

10.4 Stand-alone operation

In the stand-alone mode the transponder operates with no need of any further connections to

a fire alarm system. To connect local arm devices the relay common fire (Sa-Feu) and/or

common fault (Sa-Stör) may be used.

A fault message may be transmitted via the common fault relay to, e.g. a supervising system

or an authorized person.

Reset

To reset the transponder connect an external reset button (refer to c) or a relay contact. In

this case a voltage of 9 to 30 V DC must be switched for at least 1 second at the input (input +/-)

of the IQ8Wireless transponder.

9 V DC - 30 V DC

Reset

NONC

NCNO

Eing

Jumper J1 + J2

removed

IN OUT

Sa-Feuer

Common fire

Sa-Stör

Common fault

Fig. 21: Required wiring for the stand–alone operation

Connection data

• External power supply 9 V DC to 30 V DC

• Jumper J1 and J2 removed

• Reset time = 0.2 to 3 seconds

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 37

10.5 Relay outputs

The transponder provides two relay outputs >common fire alarm< and >common fault<. The

operation of the two relays cannot be changed.

If the transponder is connected to a conventional detector zone, the two relays are connected

and are thus no longer available for the >common fire alarm< or >common fault< switch

functions.

external devices

NONC

Sa-Feuer

external devices

NCNO

Sa-Stör

Fig. 22: Relay contacts (quiescent mode)

• 2 dry changeover contacts

• Maximum contact rating 30 V DC/1A

Common fire alarm (Sa-Feuer)

The relay output >Common Fire alarm< is activated when at least one assigned IQ8Wireless

base or IQ8Wireless MCP transmits a alarm or fire alarm to this transponder.

Common fault (Sa-Stör)

The >common fault relay< is always activated in normal mode without fault condition. In this

way, if the power supply fails, this relay can still send a fault alarm via the status change of the

relay.

The relay output >Common fault< is activated when at least one assigned IQ8Wireless base

or IQ8Wireless MCP transmits a fault alarm to this transponder or the transponder itself

detects a fault (e.g. power supply).

The relay activation follows the fault alarm (not latched).

IQ8Wireless transponder for wall mounting

38 FB 798941 / 10.06

10.6 Inputs

Eing

Schnittstelle

1 2 3 4 5 6 PR

Fig. 23: Position of the terminals

10.6.1 R - input

Input for connecting the transponder to a standard detector zone. This input is required for the

reset function. If the transponder is connected to the analog loop of the IQ8Control fire alarm

system, the input must not be connected.

10.6.2 P - terminal

Free terminal point

10.6.3 Interface (Schnittstelle)

No function – do not connect terminals.

This interface is for future feature extensions (e.g. direct connection of the service PC).

10.6.4 Input (Eing)

Reset input for an external RESET signal. The transponder is reset by applying voltage of

9V DC to 30V DC for at least 1 second.

10.6.5 U

Input for power supply 9 V DC to 30 V DC.

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 39

11 Commissioning

To start the IQ8Wireless transponder you will need the tools 8000 programming software from

version V1.09 or higher and the panel interface (Part No. 789862) as well as a service PC.

Start-up differs depending on whether the transponder is connected as a device on the analog

loop or to a standard detector zone input.

Example:

IQ8Wireless transponder 1 recognises all the wireless bases with adequate field strength

(coloured dark here). The tools 8000 software is used to assign the required (dark coloured)

wireless bases to the transponder 1.

Fig. 24: Recognised and assigned wireless bases of IQ8Wireless transponder 1

The IQ8Wireless detector bases that are assigned to transponder 1 can no longer be

recognised by transponder 2 when it is started up because they are already assigned to

transponder 1. All IQ8Wireless detector bases recognised by transponder 2 (light coloured)

can be assigned to wireless base 2.

The assignment of the IQ8Wireless detector bases and transponders may be changed to suit

your requirements with the tools 8000 software. When assigning, consider the quality of the

wireless link (field strength) and the distribution of the IQ8Wireless detector bases within the

monitored areas.

If an IQ8Wireless transponder is switched off or looses communication to its

assigned wireless devices during start-up

, it can again be recognised by all other

IQ8Wireless transponders – within a suitable range. During assignment the

wireless devices can be identified by the individual serial numbers. These serial

numbers are displayed in the tools 8000 software for each wireless device that is

recognised. If a wireless device is assigned to several IQ8Wireless

transponders, no guarantee can be given that the system will work properly.

To ease the commissioning procedure some helpful 3-digit trouble codes may be

displayed at the Fire alarm control panel IQ8Control. For additional information

and description of the trouble code refer to the manual of the FACP IQ8Control.

For further information about programming the IQ8Wireless transponder refer to

tools 8000 Online manual.

IQ8Wireless transponder for wall mounting

40 FB 798941 / 10.06

11.1 Analog loop

1. Connect the IQ8Wireless transponder to the analog loop of the IQ8Control fire alarm

system and the external power supply as described in "Installation".

2. Switch on the fire alarm control panel or the analog loop to which the IQ8Wireless

transponder is connected. If several IQ8Wireless transponders are connected, start these

up one after the other to prevent multiple assignment of one wireless device.

3. Conduct a wiring recognition of the loop with the service PC and the tools 8000

programming software. All devices on the analog loop are displayed.

4. Click the required IQ8Wireless transponder on this analog loop to open the dialog for

programming the wireless transponder.

5. In the menu item “Measure signal strength” check if the quality of the wireless

transmission between the transponder and the base is adequate.

6. All the wireless bases that this IQ8Wireless transponder has recognised are displayed in

menu item "Assign wireless devices“. If several IQ8Wireless transponders exist, wireless

bases that are already assigned to other IQ8Wireless transponders are not shown.

7. In the menu item “Assign wireless devices”, assign all required wireless bases to the

IQ8Wireless transponder individually. The wireless devices can be assigned individually in

individual detector zones.

8. Start-up is complete for this wireless transponder. Leave the IQ8Wireless transponder

switched on and start up any other IQ8Wireless transponders that you have.

805595

esserbus

-PLus

Service PC

Panel

Interface

789862

Fig. 25: Commissioning

Analog loop connection

IQ8Wireless transponder for wall mounting

FB 798941 / 10.06 41

11.2 Conventional detector zone input

1. Connect the external power supply to the IQ8Wireless transponder as described in

"Installation".

2. Connect the service PC to the terminals for the analog loop of the IQ8Wireless

transponder via the panel interface (Part No. 789862) and start the tools 8000

programming software.

3. Conduct a wiring recognition with the service PC and tools 8000.

4. Click the required IQ8Wireless transponder to open the programming dialog.

5. In the menu item “Measure signal strength” check if the quality of the wireless

transmission between the transponder and the base is adequate.

6. All the IQ8Wireless bases that this IQ8Wireless transponder has recognised are displayed

in menu item "Assign wireless devices“. If several IQ8Wireless transponders exist,

IQ8Wireless bases that are already assigned to other IQ8Wireless transponders are not

shown.

7. In the menu item “Assign wireless devices“, assign all required IQ8Wireless bases to the

IQ8Wireless transponder individually incl. menu option “Read detectors”.

8. Remove the connection on the terminals on the analog loop of the IQ8Wireless

transponder and disconnect the transponder for approx 5 seconds from power supply.

9. Connect the IQ8Wireless transponder to the conventional detector zone input of the fire

alarm system as described in “Installation”.

10. Start-up is complete for this IQ8Wireless transponder.

esserbus

4Z/2R

esserbus

transponder

Conventional

detector zone

Panel

Interface

789862

805595

++--

IN OUT

Service PC

Fig. 26: Commissioning

Conventional zone input

Page is loading ...

Honeywell 805595 User manual

Brand: Honeywell

Model: 805595

Category: Fire protection

Type: User manual

Download PDF

report

in other languages

Deutsch: Honeywell 805595 Benutzerhandbuch

Honeywell 805595 User manual

Honeywell 805595 User manual

in other languages

Related papers

Other documents