Trane BAYSPEK060 Installation guide

Brand: Trane

Model: BAYSPEK060

Type: Installation guide

SSAAFFEETTYY WWAARRNNIINNGG

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning

equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person

could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that

are attached to the equipment.

May 2022 1188--HHBB2200DD55--11EE--EENN

Single Point Entry Kit

BAYSPEK060

BAYSPEK061

BAYSPEK062

BAYSPEK063

BAYSPEK064

BAYSPEK065

Installer’s Guide

SAFETY SECTION

IImmppoorrttaanntt — This document contains a wiring

diagram, a parts list, and service information. This is

customer property and is to remain with this unit.

Please return to service information pack upon

completion of work.

WWAARRNNIINNGG

HHAAZZAARRDDOOUUSS VVOOLLTTAAGGEE!!

FFaaiilluurree ttoo ffoollllooww tthhiiss WWaarrnniinngg ccoouulldd rreessuulltt iinn

pprrooppeerrttyy ddaammaaggee,, sseevveerree ppeerrssoonnaall iinnjjuurryy,, oorr

ddeeaatthh..

DDiissccoonnnneecctt aallll eelleeccttrriicc ppoowweerr,, iinncclluuddiinngg rreemmoottee

ddiissccoonnnneeccttss bbeeffoorree sseerrvviicciinngg.. FFoollllooww pprrooppeerr

lloocckkoouutt//ttaaggoouutt pprroocceedduurreess ttoo eennssuurree tthhee ppoowweerr

ccaannnnoott bbee iinnaaddvveerrtteennttllyy eenneerrggiizzeedd..

WWAARRNNIINNGG

SSAAFFEETTYY AANNDD EELLEECCTTRRIICCAALL HHAAZZAARRDD!!

FFaaiilluurree ttoo ffoollllooww tthhiiss WWaarrnniinngg ccoouulldd rreessuulltt iinn

pprrooppeerrttyy ddaammaaggee,, sseevveerree ppeerrssoonnaall iinnjjuurryy,, oorr

ddeeaatthh..

TThheessee sseerrvviicciinngg iinnssttrruuccttiioonnss aarree ffoorr uussee bbyy

qquuaalliiffiieedd ppeerrssoonnnneell oonnllyy.. TToo rreedduuccee tthhee rriisskk ooff

eelleeccttrriiccaall sshhoocckk,, ddoo nnoott ppeerrffoorrmm aannyy sseerrvviicciinngg

ootthheerr tthhaann tthhaatt ccoonnttaaiinneedd iinn tthheessee ooppeerraattiinngg

iinnssttrruuccttiioonnss uunnlleessss yyoouu aarree qquuaalliiffiieedd ttoo ddoo ssoo..

CCAAUUTTIIOONN

GGRROOUUNNDDIINNGG RREEQQUUIIRREEDD!!

FFaaiilluurree ttoo iinnssppeecctt oorr uussee pprrooppeerr sseerrvviiccee ttoooollss mmaayy

rreessuulltt iinn eeqquuiippmmeenntt ddaammaaggee oorr ppeerrssoonnaall iinnjjuurryy..

RReeccoonnnneecctt aallll ggrroouunnddiinngg ddeevviicceess.. AAllll ppaarrttss ooff tthhiiss

pprroodduucctt tthhaatt aarree ccaappaabbllee ooff ccoonndduuccttiinngg eelleeccttrriiccaall

ccuurrrreenntt aarree ggrroouunnddeedd.. IIff ggrroouunnddiinngg wwiirreess,, ssccrreewwss,,

ssttrraappss,, cclliippss,, nnuuttss,, oorr wwaasshheerrss uusseedd ttoo ccoommpplleettee aa

ppaatthh ttoo ggrroouunndd aarree rreemmoovveedd ffoorr sseerrvviiccee,, tthheeyy mmuusstt

bbee rreettuurrnneedd ttoo tthheeiirr oorriiggiinnaall ppoossiittiioonn aanndd pprrooppeerrllyy

ffaasstteenneedd..

WWAARRNNIINNGG

UUNNIITT CCOONNTTAAIINNSS RR--441100AA

RREEFFRRIIGGEERRAANNTT!!

FFaaiilluurree ttoo uussee pprrooppeerr sseerrvviiccee ttoooollss mmaayy rreessuulltt iinn

eeqquuiippmmeenntt ddaammaaggee oorr ppeerrssoonnaall iinnjjuurryy..

RR--441100AA ooppeerraattiinngg pprreessssuurree eexxcceeeeddss tthhee lliimmiitt ooff RR--

2222.. PPrrooppeerr sseerrvviiccee eeqquuiippmmeenntt iiss rreeqquuiirreedd.. SSeerrvviiccee

uussiinngg oonnllyy RR--441100AA RReeffrriiggeerraanntt aanndd aapppprroovveedd PPOOEE

ccoommpprreessssoorr ooiill..

WWAARRNNIINNGG

SSAAFFEETTYY HHAAZZAARRDD!!

OOppeerraattiinngg tthhee uunniitt wwiitthhoouutt tthhee aacccceessss ppaanneellss

pprrooppeerrllyy iinnssttaalllleedd mmaayy rreessuulltt iinn sseevveerree ppeerrssoonnaall

iinnjjuurryy oorr ddeeaatthh..

DDoo nnoott ooppeerraattee tthhee uunniitt wwiitthhoouutt tthhee eevvaappoorraattoorr ffaann

aacccceessss ppaanneell oorr eevvaappoorraattoorr ccooiill aacccceessss ppaanneell iinn

ppllaaccee..

WWAARRNNIINNGG

WWAARRNNIINNGG!!

TThhiiss pprroodduucctt ccaann eexxppoossee yyoouu ttoo cchheemmiiccaallss

iinncclluuddiinngg lleeaadd,, wwhhiicchh aarree kknnoowwnn ttoo tthhee SSttaattee ooff

CCaalliiffoorrnniiaa ttoo ccaauussee ccaanncceerr aanndd bbiirrtthh ddeeffeeccttss oorr

ootthheerr rreepprroodduuccttiivvee hhaarrmm.. FFoorr mmoorree iinnffoorrmmaattiioonn ggoo

ttoo wwwwww..PP6655WWaarrnniinnggss..ccaa..ggoovv..

IImmppoorrttaanntt:: Wear appropriate gloves, arm sleeve

protectors and eye protection when

servicing or maintaining this equipment.

IImmppoorrttaanntt:: Air filters and media wheels or plates shall

meet the test requirements in UL 900.

18-HB20D5-1E-EN 3

General Information . . . . . . . . . . . . . . . . . . . . . . . . 4 BAYSPEK with Heater Models . . . . . . . . . . . . . . 5

Table of Contents

418-HB20D5-1E-EN

General Information

Follow these instructions to install the Single-Point

Power Entry Kit (SPEK) in single packaged units.

1. Check for any shipping damage, and if any, report it

to the carrier immediately.

2. Check the single power entry kit nameplate to

ensure available power supply complies with the

particular single power entry kit, heater and unit

model being used.

3. The field electrical connections and wiring must be

done in accordance with the “National Electrical

Code” and must comply with local electrical codes.

IInnssttaallll SSiinnggllee PPoowweerr EEnnttrryy KKiitt

1. Remove the Control/Heat panel.

2. Open the louvered Heater Control box door and

mount the SPEK inside the Heater Control box.

Secure the SPEK with the screws provided in the kit.

See illustrations and wiring diagrams throughout

this guide.

3. Insert the included grommet in the hole in the

heater Control box base that leads to the unit

Control/Heater compartment. The unit power wires

provided with the SPEK will pass through this

grommet and be routed up to the unit contactor.

4. Make all electrical connections to the unit and

heater in accordance with the appropriate wiring

diagram in this instruction and included with the

specific SPEK.

5. Place the included SPEK wiring diagram on the

inner surface of the Control/Heater access panel

next to the unit wiring diagram and extra heater

wiring diagram.

IImmppoorrttaanntt:: The two (2) nameplate labels included with

the single power entry kit must be attached

to the air conditioning unit or heat pump

unit as illustrated in

The smaller label MMUUSSTT be placed over the

unit rating nameplate to cover the unit only

MCA and Fusing.

Check the appropriate kit, heaters and unit

combination using the tables in this guide.

HHiigghh VVoollttaaggee FFiieelldd WWiirriinngg

NNoottee:: All field wire to be rated 75°C minimum.

Maximum field wire size is 2/0 AWG.

1. Check to make certain the proper size fuses are

installed per the fuse table ( located on the wiring

diagram) and the ampacity and max fuse/circuit

breaker tables for the particular SPEK being used.

2. Remove the required electrical knockout from the

unit conduit panel and route the field wires through

the u nit heater section (not the Control Box

section).

3. Connect the power supply to the terminal block or

fuse block (depending on SPEK kit being used) on

the SPEK. See appropriate wiring diagram for

hookup connections. Connect the power supply

ground wire to the ground lug on the single power

entry kit. The BAYSPEK060 and 061 wire terminals

connect to the installed heater terminal block on the

Heater Control box base to power the unit.

4. Close the Heater/SPEK control box cover.

5. Reinstall the Control/Heat access panel.

6. Apply power to the unit.

LLooww VVoollttaaggee WWiirriinngg ((2244 VVoollttss))

All lower voltage connections have been made to the

heater via polarized plugs. The low voltage controls are

connected to the room thermostat from the air

conditioner or heat pump low voltage leads. See the

field wiring diagram with the unit.

Figure 1. Single Point Power Entry Kit Label Positions

Heater Installed

Nameplate

Place SPEK Nameplate

Over Heater Label

Unit Namplate

Place Smaller Label

to Cover Unit Only MCA

and Fusing

Single Power Entry Knockout

18-HB20D5-1E-EN 5

BAYSPEK with Heater Models

Figure 2. BAYSPEK060

618-HB20D5-1E-EN

Figure 3. BAYSPEK061

D932299P02

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

18-HB20D5-1E-EN 7

Figure 4. BAYSPEK062

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

818-HB20D5-1E-EN

Figure 5. BAYSPEK063, 064 and 065

D932299P10

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

18-HB20D5-1E-EN 9

Figure 6. BAYSPEK060

BK - 2

RD - 1

WIRE TIES

WIRE

NO.

Figure 7. BAYSPEK060 WIRING

D673487P01

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

10 18-HB20D5-1E-EN

Figure 8. BAYSPEK061

BK - 2

BL - 3

RD - 1

WIRE TIES

WIRE

NO.

Figure 9. BAYSPEK061 WIRING

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

18-HB20D5-1E-EN 11

Figure 10. BAYSPEK062

Figure 11. BAYSPEK062 WIRING

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

12 18-HB20D5-1E-EN

Figure 12. BAYSPEK063

Figure 13. BAYSPEK063 Wiring

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

18-HB20D5-1E-EN 13

Figure 14. BAYSPEK064

Figure 15. BAYSPEK064 — Wiring

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

14 18-HB20D5-1E-EN

Figure 16. BAYSPEK065

Figure 17. BAYSPEK065–Wiring

BBAAYYSSPPEEKK wwiitthh HHeeaatteerr MMooddeellss

18-HB20D5-1E-EN 15

NNootteess

About Trane and American Standard Heating and Air Conditioning

Trane and American Standard create comfortable, energy efficient indoor environments for residential applications. For

more information, please visit www.trane.com or www.americanstandardair.com.

The manufacturer has a policy of continuous data improvement and it reserves the right to change design and specifications without notice. We are committed to

using environmentally conscious print practices.

18-HB20D5-1E-EN 31 May 2022