2. Visionis
  3. VS-SS800-DL
VS-SS800-DL

Visionis VS-SS800-DL Installation guide

  • Hello! I have reviewed the user guide for the VISIONIS Electromagnetic Lock VS-SS800-DL. This document provides step-by-step instructions on installing the lock, wiring it correctly, and maintaining it for long-term use. I'm ready to address your questions regarding its specifications, features, or usage based on this manual.
  • What is the holding force of the lock?
    What is the recommended maintenance for the lock?
    What are the voltage input options for the lock?
VS-SS800-DL
800 Lbs Outdoor and Gate
Electromagnetic Lock with
Armored Door Loop
ref.
Disclaimer: VISIONIS reserve the right to go ahead with any modifications of models or features or price without forewarning. All the
information and specifications stated in this document are current at the time of publication. Attention: We are not responsible for the
improper installation of this kit. If you are not handy with electrical equipment you should contact a professional electrician. You will also
need to check with your local Fire authority to see if you need anything else to comply with local Fire Codes. We are not responsible for
any damage or fees that can occur.
www.visionistech.com
[email protected]
Technology Within Your Reach
Installation User Guide (Outdoor Models)
Basic Installation Concept & Accessories
Side Mounting
General Installation Steps & Maintenance
1. Drill the armature plate holes in the door using the sticker template provided.
2. Attach the armature plate to the door with the hardware provided as per the illustration.
3. With the door closed, mark the door frame at the edge of the armature in order to properly align the electromagnet to the armature.
4. Attach the mounting plate to the door frame using the self-tapping screws provided. Align the mounting plate with the mark from the
previous instruction.
5. Insert the wires through the hole in the mounting plate and attach the electromagnet unit to the mounting plate with the allen head
fixing screw.
6. Connect the power wires according to the instruction and test the system.
7. It is recommended that to apply a light coat of silicon lubricant to the mating surface on a monthly basis to prevent rust.
Mounting Plate
(Side Bar)
Armored Loop
Cable Wire
Self-tapping Screw
Allen Wrench
Armature
Screw
Armature Plate
Guide Pin
Rubber
Washer
Metal
Washer
Sexnut Bolt
Anti Residual
Magnetism
Button
Wiring Instructions
RED
GREEN
BLUE
ORANGE
NC
NO
COM
REED SENSOR CONTACT
RED
YELLOW YELLOW
WHITE WHITE
BLACK BLACK
24 VDC
++
12 VDC -
-
IMPORTANT!
Before the power supply is switched on, set the wiring correctly.
VS-SS800-DL
800 Lbs Outdoor and Gate
Electromagnetic Lock with
Armored Door Loop
ref.
Disclaimer: VISIONIS reserve the right to go ahead with any modifications of models or features or price without forewarning. All the
information and specifications stated in this document are current at the time of publication. Attention: We are not responsible for the
improper installation of this kit. If you are not handy with electrical equipment you should contact a professional electrician. You will also
need to check with your local Fire authority to see if you need anything else to comply with local Fire Codes. We are not responsible for
any damage or fees that can occur.
www.visionistech.com
[email protected]
Technology Within Your Reach
Specifications
Voltage Input: 12 VDC / 24 VDC
Current Draw: 12V / 480mA; 24V / 240mA (±5%)
Holding Force: Up to 800 lbs (362 kg)
Hall Effect Reed Contact: 28 VDC, 0.2A, 5W
Anti-Rust Surface Treatment: Blue Zinc Plating
Operating Temperature: 0°C~55°C ( 32°F~131°F)
Operating Humidity: 0~95% (non condensing)
Weight (Magnet): 2.3 kg (±1%)
Dimensions: Magnet - (L) 220x (W) 46x (T) 28 mm - (L) 8.66 x (W) 1.81 x (T) 1.10 in.
Armature - (L) 182x (W) 44x (T) 12 mm - (L) 7.16 x (W) 1.73 x (T) 0.47 in.
/