2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. ERGODIRECT
  6. STX-02S
STX-02S

ERGODIRECT STX-02S User manual

  • Hello! I have reviewed the installation instructions for the HAT Collective Monitor Mounts, specifically models STX-02W, STX-22W, STX-02S and STX-22S. This manual provides detailed guidance on desk clamp and thru-desk mounting options, along with clear part diagrams. I'm ready to assist you with any questions you have about assembling and setting up your monitor mount.
  • What is the maximum desk thickness for desk clamp configuration?
    What is included with the optional thru-desk kit?
    What tool is used to adjust the tilter friction?
STX-02S
STX-22S
STX-22W
STX-02W
STA X X
Installation Instructions
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
HAT Collective
408 437 8770
cs@hatcollective.com
hatcollective.com
™
© 2021 Innovative Ergonomic Solutions REV APAGE 1 OF 11
A Top Down Mount
8524
B Dimpled Pole
110607-14
C Stackable Mount
413054
D Pole Collar
113332
E Pole Clip
113449
F Bushing Adapter
112945
G Rotation Stop for Extension Arms
113703
H 10-32 x 5/8" Phillips Pan Head Screw
702200
I Quick Connect VESA Plate
114808
J M4 x 12mm Phillips Pan Head Screw
701153
K Monitor Tilter
8500 Tilter
L Dog Washer
105189
M 10-32 x 3/8" FPhMS w/Lock Patch
705198
N Pole Cap
105195
O Cable Clip
104533
P Cable Cap
114810
Q 1/8" Allen Wrench
701312
R 3/32" Allen Wrench
700146
S 7/32" Allen Wrench
701127
T* M8 x 95mm SCHS
716061
U* Spacer
701544
V* Lock Nut
710015
* Included with optional thru-desk kit only, model # 8524-TM-CK (sold separately).
PARTS LIST
PAGE 2 OF 11
S
A
OR
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
DESK CLAMP CONFIGURATION
PAGE 3 OF 11
3 4
THRU-DESK CONFIGURATION*
* Thru-desk kit required, model # 8524-TM-CK (sold separately).
S
T
U
V
7/32"
Desk thickness
up to 1.5" (3.8 cm)
PAGE 4 OF 11
5
R
B
C
D
i
IMPORTAN T:
When inserting
pole into mount,
the dimples
should be aligned
perpendicular to
the rear edge of
mounting surface.
Dimples
3/32"
PAGE 5 OF 11
6
E
PAGE 6 OF 11
F
F
G
G
G
H
H
L
M
L
iIMPORTAN T: Install part (G)
in the orientation as shown
above. When washer, part
(G), is installed correctly, the
lower extension arms will
not rotate past the back of
the mount.
H
M
7 8
PAGE 7 OF 11
9
J
J
I
PAGE 8 OF 11
10
K
PAGE 9 OF 11
L
L
M
M
11
iTILTER FRICTION ADJUSTMENT
Q
1/8"
PAGE 10 OF 11
O
N
12
PAGE 11 OF 11
/