Kichler 300345BNB User manual

Product images may vary slightly from actual product.

52" Vinea

INSTRUCTION MANUAL

Model# 300345READ AND SAVE THESE INSTRUCTIONS

2 | KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES ..............................................................3

TOOLS REQUIRED ........................................................5

PACKAGE CONTENTS .................................................5

MOUNTING OPTIONS .................................................6

HANGING THE MOTOR ASSEMBLY .........................7

INSTALLATION OF SAFETY SUPPORT ...................10

ELECTRICAL CONNECTIONS ...................................11

COMPLETING THE MOTOR INSTALLATION ........12

ATTACHING THE FAN BLADES ................................13

INSTALLING THE LIGHT PLATE ..........................………............14

INSTALLING THE LIGHT KIT AND GLASS SHADE ...............15

INSTALLING THE “COOLTOUCH” CONTROL SYSTEM

WALL PLATE .................................................................................16

INSTALLING AND REMOVING THE HANDHELD

TRANSMITTER ............................................…..............................17

OPERATING INSTRUCTIONS ....................................................17

REVERSE FUNCTION .................................................................19

FCC INFORMATION ....................................................................19

TROUBLESHOOTING ................................................................20

1. CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel

or main fusebox before starting and during the

installation.

2. WARNING: This fixture is intended for installation in

accordance with the National Electrical Code (NEC)

and all local code specifications. If you are not familiar

with code requirements, installation by a certified

electrician is recommended.

3. WARNING: To reduce the risk of fire or electric shock,

use only the control provided with the fan.

4. WARNING: To reduce the risk of fire, electric shock,

or Personal Injury mount to an outlet box marked

“Acceptable For Fan Support of up to 15.9 kg (35 lbs)”.

For outlet box mounting, use mounting screws (and

lock washers) provided with the outlet box. Most

outlet boxes commonly used for the support of light

fixtures are not acceptable for fan support and may

need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician

is strongly recommended.

5. WARNING: Chemical Burn Hazard. Keep batteries

away from children.; and

This product contains a lithium button/coin cell

battery. If a new or used lithium button/coin cell

battery is swallowed or enters the body, it can cause

severe internal burns and can lead to death in as little

as 2 hours. Always completely secure the battery

compartment. If the battery compartment does not

close securely, stop using the product, remove the

batteries, and keep it away from children. If you think

batteries might have been swallowed or placed inside

any part of the body, seek immediate medical attention.

a) The cells shall be disposed of properly, including

keeping them away from children; and

b) Even used cells may cause injury.

6. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70 and local electrical

codes. Electrical installation should be performed by a

qualified licensed electrician.

READ AND SAVE THESE INSTRUCTIONS

SAFETY RULES

WARNING: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO THE BUILDING STRUCTURE / CEILING JOIST.

DON’T SECURE THIS FAN TO AN OUTLET BOX.

52" Vinea | 3

4 | KICHLER.COM

15. After making the electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be spread

apart with the grounded conductor and the equipment-

grounding conductor on one side of the outlet box and

the ungrounded conductor on the other side of the

outlet box.

16. Electrical diagrams are for reference only. Light kits

that are not packed with the fan must be ETL Listed

and marked suitable for use with the model fan you are

installing. Switches must be ETL General Use Switches.

Refer to the Instructions packaged with the light kits

and switches for proper assembly.

17. All set screws must be checked, and retightened where

necessary, before installation.

18. The subject fan 300345 weight information is as below:

Net Weight : 10.3 kgs / 22.66 lbs;

Gross Weight: 11.7 kgs /25.74 lbs.

7. The outlet box and support structure must be

securely mounted and capable of reliably supporting

a minimum of 15.9 kg (35 pounds). Use only cULus

Listed outlet boxes marked “FOR FAN SUPPORT”.

8. WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT

FAN TO OUTLET BOX MARKED “ACCEPTABLE FOR

FAN SUPPORT”.

9. Avoid placing objects in the path of the blades.

10. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

11. To operate the reverse function on this fan, press the

reverse button while the fan is running.

12. Make sure the installation site you choose allows a

minimum clearance of 2.1 m (7 feet) from the blades

to the floor and at least 30 inches from the ends of the

blades to any obstruction.

13. WARNING: make sure the power is disconnected

before cleaning your fan.

14. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE BRACKETS DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

52" Vinea | 5

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

• Phillips Screwdriver

• Blade Screwdriver

• 11 mm Wrench

• Step Ladder

• Wire Cutters

Unpack your fan and check the contents . You should have the following items:

A. Mounting Bracket

B. Ball / Downrod Assembly

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Assembly

G. Fan Blade (5)

H. Blade Bracket (5)

I. Light Plate

J. Light Kit

K. Glass Shade

L. Finial

M. Wall control Kit:

Receiver (1), Control (1), Metal Plate (1),

Wire connector (6), Wood Screw (2),

Battery (2), Long Screw (2),

Short Screw (2), Expansion Anchor (2),

Plastic Nut (2)

N. Package hardware

1.) Mounting hardware :

Wire Connector (3)

2.) Blade attachment hardware :

Screws (15) , Washers (15)

3.) Safety cable hardware :

Wood screw (1) ,

Spring washer (1),

Flat washer (1)

4.) Light kit attachment hardware:

Screw (3);

A

F

J

I

G

H

K

B

C

D

E

M

L

N

X3

X1

X15

X3

6 | KICHLER.COM

MOUNTING OPTIONS

If there is not an existing UL (cUL for Canadian Installation)

listed mounting box, then read the following instructions.

Disconnect the power by removing fuses or turning o circuit

breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the full weight

of the fan (up to 15.9kg (35 pounds)). Do not use plastic outlet

boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for optimal operation.

NOTE: You must use 12" or longer downrod for 22° slope

(max angle 22°). (Fig. 3)

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a joist

hanger for the support of the outlet box. Make sure the joist

hanger you purchase has been designed for use with ceiling

fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Fig. 4

Outlet box

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 22° ANGLE

52" Vinea | 7

Fig. 5

Fig. 6

Fig. 7

Outlet Box

Ceiling Mounting

Bracket

Flat Washer

Screw

Set Screw

Hanger Ball

Cross Pin

Clevis Pin

Downrod

Hairpin

HANGING THE MOTOR ASSEMBLY

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 5)

Step 2. Remove the hairpin and clevis pin from the downrod assembly, retain for later

use. Remove the hanger ball from the downrod assembly by loosening set screw,

removing the cross pin, and sliding ball of the rod. (Fig. 6)

NOTE: Make sure to keep loosened hardware separate to avoid confusion during

installation.

Step 3. Loosen the two set screws on the motor coupling. (Fig. 7)

8 | KICHLER.COM

Step 4. Carefully feed fan wires and safety cable up through the downrod.

Thread the downrod onto the motor coupling until the clevis pin holes

are aligned. Next, replace the clevis pin and hairpin, then tighten both set

screws. (Fig. 8)

Step 5. Slip the coupling cover, canopy hole cover and canopy onto the

downrod. Carefully reinstall the hanger ball onto the downrod. Make sure

the cross pin is in the correct position and the set screw is tight and the

wires are not twisted . ( Fig. 9)

CAUTION: Ensure all screws are tight before moving to the next step.

HANGING THE MOTOR ASSEMBLY (continued)

Motor

Coupling

Canopy

Hanger Ball

Cross Pin

Canopy Hole Cover

Coupling Cover

Downrod

Hairpin Clevis Pin

Set Screw

Fig. 8

Fig. 9

52" Vinea | 9

Step 6. Now lift the motor assembly into position and place the hanger ball into

the mounting bracket. Rotate until the check tab has dropped into the registration

slot and seats firmly. ( Fig. 10) The entire motor body should not rotate if this is

done correctly.

WARNING: Failure to properly seat the check tab can damage the ceiling fan

during operation.

HANGING THE MOTOR ASSEMBLY (continued)

Fig. 10

Check Tab

Registration

Slot

10 | KICHLER.COM

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig. 12)

NOTE: Although the safety support cable is required for Canadian installations only,

it’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 12

Fig. 11

52" Vinea | 11

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power

at the main circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connectors with electrical tape. Make

sure there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual,

stop immediately. A professional electrician is recommended to determine proper

wiring.

Step 1. Insert the receiver into the mounting bracket, and keep flat in opposition of

ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connections: Connect the BLACK wire from the fan

to BLACK wire marked “TO MOTOR L” from the receiver. Connect the WHITE wire from

the fan to the WHITE wire marked “TO MOTOR N” from the receiver. Connect the BLUE

wire from the fan to the BLUE wire marked “FOR LIGHT “ from the receiver. Secure all

the wire connections with the plastic wire connectors provided. ( Fig. 14)

Step 3. Remote Receiver to Outlet Box Electrical Connections: Connect the BLACK (hot)

wire from the ceiling to the BLACK wire marked “AC IN L” from the receiver. Connect

the WHITE (Neutral ) wire from the ceiling to the WHITE wire marked “ AC IN N” from

the receiver. Secure all the wire connections with the plastic wire connectors provided.

( Fig. 14)

Fig. 14

Fig. 13

Mounting Bracket

Receiver

Green or bare copper (ground)

AC IN N (White)

White (“TO MOTOR N”)

Ground wire

White (Neutral)

AC IN L (Black)

Receiver

Black (“TO MOTOR L”)

Black (motor)

Blue (FOR LIGHT)

Blue (for light)

Black (“AC IN L”) White (“AC IN N”)

Ground wire

12 | KICHLER.COM

ELECTRICAL CONNECTIONS

Step 4. If your outlet box has a ground wire (green or bare copper) connect

it to the fan ground wires. Otherwise, connect the fan ground wire to the

mounting bracket. Secure the wire connection with a plastic nut provided.

After connecting the wires, spread them apart so that the green and white

wires are on one side of the outlet box and black and blue wires are on the

other side. (Fig. 14)

NOTE: Carefully tuck the wire connections up into the outlet box.

NOTE: Fan must be installed at a maximum distance of 30 feet from the

transmitting unit for proper signal transmission between the transmitting

unit and the fan’s receiving unit.

COMPLETING THE MOTOR INSTALLATION

Step 1. Remove one of the two shoulder screws in the mounting bracket.

Loosen the second shoulder screw without fully removing it. (Fig. 15)

Step 2. Assemble canopy by rotating key slot in canopy over shoulder

screw in mounting bracket. Reinstall the shoulder screw that was previously

removed, then retighten two shoulder screws securely. (Fig. 16)

Step 3. Securely attach and tighten the canopy hole cover over the shoulder

screws in the mounting bracket utilizing the keyslot twist-lock feature.(Fig.17)

Mounting

Bracket

Shoulder

Screw

Shoulder

Screw

Shoulder

Screw

Canopy

Hole Cover

Canopy

Fig. 16

Fig. 15

Fig. 17

52" Vinea | 13

ATTACHING THE FAN BLADES

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical

Supply Circuit To The Fan Before Installing Fan Blades.

Step 1. Attach blade to blade bracket using three blade screws and three

washers found in the hardware pack as shown. Do not tighten blade screws until

each screw has been started. Then, tighten each screw starting with the center

screw. (Fig. 18)

Repeat for remaining blades.

Step 2. Fasten blade assembly to the holes located on the bottom of the motor

assembly. Tighten the two pre-installed motor screws in the blade bracket.

Repeat steps for the remaining blade assemblies. (Fig.19)

Fig. 18

Fig. 19

Blade Screw

Blade Washer

Blade

Blade Bracket

Motor Assembly

Blade Assembly

14 | KICHLER.COM

INSTALLING THE LIGHT PLATE

Step 1. Remove the screw marked with a brown dot label which on the

mounting plate and keep for later use. Loosen the other two (do not remove).

(Fig.20)

Step 2. Place the two slot holes on the light plate over the 2 screws previously

loosened from the mounting plate. Rotate the light plate until it locks in

place at the narrow end of the key holes. Secure by tightening the 2 screws

previously loosened and the one previously removed. (Fig. 21) Screw

Mounting Plate

Light Plate

Fig. 20

Fig. 21

52" Vinea | 15

INSTALLING THE LIGHT KIT AND GLASS SHADE

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical

Supply Circuit To The Fan Before Installing Light Kit.

Step 1. Hold the LED light kit to light plate, then connect the 2 single pin connectors

from the light kit to the 2 single pin connectors from the motor assembly. Connect

the black wire to the black wire, and white wire to the white wire. Attach the light

kit to the light plate and securely tighten with three (3) screws from the screw pack

(Fig. 22)

Step 2. Remove and retain the manual nut, metal washer and silicone washer from

the threaded rod on the light kit. (Fig. 23)

Step 3. Lift the glass shade up to the light kit, allowing the threaded rod to go

through the center hole in the bottom of the glass shade. Place the silicon washer

and metal washer over the threaded rod, then screw the manual nut onto the

threaded rod until tight. DO NOT OVER-TIGHTEN. (Fig. 23)

Step 4. Screw the finial to the threaded rod and securely tighten. (Fig. 23)

Fig. 22

Fig. 23

Light Kit

Silicon Washer

Manual Nut

Metal Washer

Finial

16 | KICHLER.COM

CAUTION: MAKE SURE THE ELECTRICITY IS TURNED OFF AT THE MAIN JUNCTION

BOX OR THE CORRECT FUSE HAS BEEN PULLED OFF AT THE MAIN JUNCTION BOX

BEFORE CONTINUING.

WARNING: All wiring must be in accordance with the National Electrical Code local

electrical codes. Electrical installation should be performed by a qualified licensed

electrician.

Select a location to install your “CoolTouch” Control System Transmitter. You can replace

an existing wall switch, or install the transmitter on ANY flat surface.

WARNING: SWITCH INSTALLATION MUST COMPLY WITH ALL LOCAL AND

NATIONAL ELECTRIC CODES.

Option 1. Install the control system using an existing wall switch outlet box.

Make sure the electrical power is TURNED OFF at the main panel before wiring.

Step 1. Remove the existing wall plate and the old switch from the wall outlet box. Wire the

BLACK leads (hot) together with connector and push back inside the outlet box. (Fig. 24)

Step 2. Install the metal plate and “CoolTouch” wall plate to the existing wall outlet box

with 4 screws provided. Then place the two plastic plugs into the wall plate. (Fig. 25)

Option 2: Install the control system on ANY flat surface:

Select the desired location and use the “CoolTouch” wall plate to make the location for the

mounting holes. Plastic wall anchors and screws are provided for this type of installation.

After installing the wall anchors, attach the “CoolTouch” wall plate with the mounting

screws and then insert the plastic plugs to finish installation.

INSTALLING THE COOLTOUCH™ CONTROL SYSTEM WALL PLATE

Fig. 24

Fig. 25

Outlet Box

Switch

Wall Plate

Outlet Box

Metal Plate

Screw

“CoolTouch” Wall Plate

Screw

Plastic Plug

52" Vinea | 17

INSTALLING AND REMOVING THE HANDHELD TRANSMITTER

Step 1. To place the transmitter in the wall plate, put the bottom end in first and

then press the top into the wall plate. The transmitter is now held in the wall plate

and will function from here. (Fig.26)

Step 2. To remove the transmitter from the wall plate, push the release button

and the transmitter will fall into your hand.

Fig. 26

OPERATING INSTRUCTIONS

WARNING: Chemical Burn Hazard. Keep batteries away from children.

Step 1. Using a screwdriver, remove the battery cover from the handset and save

the screw for later use. (Fig. 27)

Step 2. To make fan operational, install two 3V CR2032 batteries (included). The

batteries should be installed with the positive (+) side up. Replace with CR2032

batteries when necessary. (Fig. 28)

NOTE: If not used for long periods of time, remove batteries to prevent damage

to the handset control. Store the control away from excessive heat or humidity.

Fig. 27

Fig. 28

Batteries

18 | KICHLER.COM

OPERATING INSTRUCTIONS

NOTE: Each handset control carries a unique ID code to facilitate communication between paired

devices. The ID code is set by factory and is not user changeable. However, you will be required to

perform an ID code learning process manually under these circumstances:

• If you have multiple fans installed within a close proximity and want to control all fans using a

same handset control.

NOTE: Each fan requires its own receiver.

• When your remote control is not responding (make sure battery is not dead).

• After you have replaced a faulty transmitter or receiver with a new one.

Otherwise the remote control will not work. To perform this process manually, follow steps below:

After installing and wiring the unit, restore power to your fan, press and hold the “LEARN” key

for 1-3 seconds, and the fan will turn on at medium speed and light (if installed) will turn on. This

confirms that the learning process has been completed. This operation must be completed within

30 seconds after restoring power to the fan. (Fig. 29)

NOTE: Ensure slide switch in battery compartment marked “D O” is set to “D” position. (Fig. 29)

Step 4. Replace the battery cover and tighten with screwdriver. (Fig. 29)

Step 5. The buttons control the fan speed and light as follows: (Fig. 30)

Fig. 30

Fig. 29

Battery Cover

Screw

Fig. 29

Fig. 30

Battery Cover

Screw

Low speed

Medium speed

High speed

Fan OFF

Airflow (Forward or Reverse)

No function (Do not use this button)

a.) Light ON/OFF.

b.) Press and hold to dim or brighten light to desired level.

52" Vinea | 19

Fig. 31 Fig. 32

REVERSE FUNCTION

To operate the reverse function on this fan, press the “Reverse”

button while fan is running. Speed setting for warm or cool weather

depends on factors such as the room size, ceiling height, number of

fans and so on.

Warm Weather Operation: Warm Weather Operation: Forward (counter clockwise). A downward

airflow creates a cooling eect (Fig. 31). This allows you to set your

air conditioner on a warmer setting without aecting your general

comfort.

Cool Weather Operation: Cool Weather Operation: Reverse (clockwise). An upward airflow

moves warm air off of the ceiling (Fig. 32). This allows you to set

your heating unit on a cooler setting without aecting your general

comfort.

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.)This device may not cause harmful interference, and

2.)This device must accept any interference received, including interference that may cause undesired operation.

Note: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician or help.

20 | KICHLER.COM

TROUBLESHOOTING

ProblemProblem

Fan will not start.Fan will not start.

Fan sounds noisy.Fan sounds noisy.

Fan wobble.Fan wobble.

Remote control Remote control

malfunction.malfunction.

SolutionSolution

1. Check circuit fuses or breakers.1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact. 2. Check all electrical connections to ensure proper contact. CAUTION: Make sure the main power is OFF when checking CAUTION: Make sure the main power is OFF when checking

any electrical connection.any electrical connection.

3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.

4. Ensure the batteries have a good charge.4. Ensure the batteries have a good charge.

1. Make sure all motor housing screws are snug.1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing. 3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is o.CAUTION: Make sure main power is o.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not 5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not

touching any other component.touching any other component.

6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or 6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or

remote controls.remote controls.

7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.

1. Check that all blade and blade arm screws are secure.1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling 2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling

above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement. above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement.

Repeat for each blade. The distance deviation should be equal within 1/8".Repeat for each blade. The distance deviation should be equal within 1/8".

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and 3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and

possibly result in smoother operation. possibly result in smoother operation.

1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT a 1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT a

basic On/o wall switch, if desired.basic On/o wall switch, if desired.

Page is loading ...