FMI LPA6000 Operating instructions

Brand: FMI

Model: LPA6000

Type: Operating instructions

104795 01

Outlet: 3/8" FPT

Capacity: 160,000 Btu/Hour

WARNING: This low pressure regulator is designed

to regulate propane vapor only. This regulator meets all

the standards and safety codes for use on a horizontal

ASME tank or single vertical cylinder. The brass con-



left-hand threads. The vent must be pointing down

towards the ground when the regulator is properly

mounted (see Figure 1).



systems which allow liquid and debris to enter the

vapor system.



assembly be used immediately downstream of this regula-



long, marked “”, “”, -

”.

• This regulator must be installed in compliance with federal, state,

local codes and laws, and in accordance with NFPA/ANS 58,

Storage and Handling of Liqueed Petroleum Gases.

• Read and follow manufacturers’ instructions when installing this

regulator to a propane gas cylinder.



in a building, garage, or enclosed area.

• The two stages of the model LPA6000 regulator reduce full cylin-

der pressure down to 11" water column outlet pressure nominally

at room temperature.

• The gas appliance(s) served by this regulator must be supplied

with at least the minimum inlet pressure as specied by the manu-

facturer of the appliance(s). A qualied propane service person

should verify proper supply pressure at all appliances.

      

adjust, or service this propane gas regulator. If service

-

cian or dealer.



hear, see, or smell leaking propane gas, close all open

valves, and immediately get everyone away from the

-

tempt repairs.





        

close valve and have propane gas service person

make needed repairs. Also, check all appliance valves

and connections to make sure they do not leak before

lighting appliance.

LOW PRESSURE TWO-STAGE PROPANE/LP GAS

REGULATOR KIT MODEL LPA6000

For Use with Propane/LP Fueled Indoor Heating Appliances**

104795-01

Rev. C

02/07

Pressure

Relief

Valve

Cylinder Valve

Regulator Nut

or Connection

2-Stage Regulator

Cylinder

Regulator

Vent

Liquid Level

Indicator (Optional)

Figure 1 - Checking Gas Leaks

NOT A UPC

** Follow appliance manufacturer’s installation instructions.

Vent Must Point Down

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

• The transportation, installation, and storage of propane cylinders

must be in compliance with federal, state, and local codes, and in

accordance with NFPA/ANS 58, Storage and Handling of Lique-

ed Petroleum Gases.

• The design, materials, components, installation, repairs, and main-

tenance of the gas piping system connected to this regulator must

be in compliance with federal, state, and local codes and should

comply with National Fuel Gas Code ANS Z223.1, NFPA 54.

• Protect this regulator from the elements by using the vented

protective cover included in this kit.





Your regulator is equipped with a vent because it is constantly “breath-

ing.” That is, the diaphragm of the regulator moves down and draws

air into the bonnet or adjustment spring housing. When the diaphragm

moves up, air is expelled through the vent. In the event that excess

pressure builds up in the lower housing or body of the regulator, a

relief mechanism vents it to the atmosphere. So, it is imperative to

check the vent frequently to be sure it is clean and free of water,

corrosion, or obstructions as clogging is the most common cause of

regulator malfunction. Great care has been taken in the manufacture

of your regulator and it has been thoroughly tested and U.L. listed.

However, even a small piece of dirt, corrosion, pipe dope or other

foreign matter which nds its way into the outlet can result in higher

than normal pressure (high lockup) and/or loss of fuel.

If the vent does become clogged it can easily be cleaned with a

toothbrush. In addition, your regulator should be checked periodically

by a competent propane serviceman to be sure it is properly adjusted

and in safe working condition. By following these simple precautions

your regulator will give you years of trouble free service.

If you have questions about installation, operation, or trouble-

’ Technical Service



FMI LPA6000 Operating instructions

FMI LPA6000 Operating instructions

FMI LPA6000 Operating instructions

Related papers

Other documents