Save these instructions!
Conservez précieusement ces instructions !
Diese Anleitung aufbewahren!
Conservare le presenti istruzioni!
Guarde estas instruções!
Φυλάξτε αυτές τις οδηγιες!
¡Guarde estas instrucciones!
Сохраните эту инструкцию!
Збережіть ці інструкції!
CZ-RWSU2
CZ-RWST2
CZ-RWSL2
CZ-RWSC2
CZ-RWSY2
CZ-RWSK2
EN
ES
RU
UK
FR
DE
IT
GR
PT
Wireless Remote Control System INSTRUCTION MANUAL
Système de télécommande à infrarouge MANUEL D’UTILISATION
Drahtloses Fernbedienungssystem BEDIENUNGSANLEITUNG
Sistema Telecomando Senza Fili MANUALE DI ISTRUZIONI
Sistema de telecomando sem fi os MANUAL DE INSTRUÇÕES
Ασύρματο σύστημα τηλεχειριστηριου ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ
Sistema de control remoto inalámbrico
MANUAL DE INSTRUCCIONES
Беспроводная система дистанционного управления
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
Бездротова система дистанційного керування ПОСІБНИК КОРИСТУВАЧА
85464609072022
1
2
3
4
5
6
7
8
9
10
12
11
13
14
15
16
REMOTE CONTROL / TÉLÉCOMMANDE / FERNBEDIENUNG /
TELECOMANDO / TELECOMANDO / ΤΗΛΕΧΕΙΡΙΣΤΗΡΙΟ /
CONTROL REMOTO / ПУЛЬТ ДИСТАНЦИОННОГО УПРАВЛЕНИЯ /
ПУЛЬТ ДИСТАНЦІЙНОГО КЕРУВАННЯ
Printed in China
Authorized representative in EU
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Receiver / Récepteur / Empfänger / Ricevitore / Receptor /
Δέκτης / Receptor / Приёмник / Приймач
Display / Affi chage/
Anzeige / Display
Visor / Οθόνη
Visor / Дисплей / Дисплей
1
2
3
4
5
6
7
8
9
CZ-RWSC2
1543
2
CZ-RWST2 CZ-RWSL2
345
1
2
7
8
9
Operation Panel / Panneau de commande
Bedienfeld / Pannello di Comando
Painel de comando / Πλαίσιο λειτουργίας
Panel de operaciones / Панель управления /
Панель керування
I II
3
4
5
2
Indoor Unit (CZ-RWSK2) / Appareil intérieur (CZ-RWSK2) / Raumeinheit (CZ-RWSK2) /
Apparecchio Interno (CZ-RWSK2) / Unidade interior (CZ-RWSK2) /
Εσωτερική μονάδα (
CZ-RWSK2
)
/
Unidad interior (CZ-RWSK2) /
Внутренний блок
(CZ-RWSK2) /
Внутрішній блок
(CZ-RWSK2)
2
3
4
5
1
CZ-RWSY2
CZ-RWSU2
EN-1
EN
Contents
1. Important Safety Instructions ...............................................EN-2
2. Names and Operations ........................................................EN-3
3. Installing Batteries ................................................................EN-5
4. Setting the Current Time ......................................................EN-6
5. Operation .............................................................................EN-7
6. Timer Operation ...................................................................EN-9
7. Adjusting the Wind Direction ..............................................EN-11
8. Operating Multiple In/Outdoor Units Simultaneously .........EN-12
9. Using the Remote Control ..................................................EN-13
10. For Best Results .................................................................EN-13
11. Addresses ..........................................................................EN-14
12. Emergency Operation ........................................................EN-17
13. Miscellaneous Settings ......................................................EN-19
14. Before Requesting Service ................................................EN-20
15. Specifi cations .....................................................................EN-21
1. Important Safety Instructions
EN-2
Before using the system, be sure to read these
“Important Safety Instructions”.
After reading this manual, save it in a convenient
place.
Warning
Installation Precautions
• Do not install yourself
Installation should always be performed by your
dealer or a professional service provider.
Electric shock or fi re may result if an
inexperienced person performs any installation
or wiring procedures incorrectly.
• Use only specifi ed air conditioners
Always use only air conditions specifi ed by the
dealer.
Precautions for Use
• Do not touch switches with wet hands
Electric shock and damage to the system can
result.
• Protect the remote controller from water Damage
to the system can result.
• Stop the system and turn the power off if you
sense unusual smells or other irregularities
Continuing operation when the system is out of
order can result in electric shock, fi re, and
damage to the system. Contact your dealer.
• Do not swallow the battery.
Moving and Repair Precautions
• Do not repair
Never repair the system by yourself.
• Contact your dealer before moving the system
Contact your dealer or a professional service
provider about moving and reinstalling the system.
Electric shock or fi re may result if an
inexperienced person performs any installation
procedures incorrectly.
2. Names and Operations
EN-3
EN
1. Operation Display
Displays the operation status. (The fi gure
shows all the statuses.)
• The auto-fl ap display may be different,
depending on the installed unit. (See Page
EN-11)
2. Start/Stop button
Pressing this button once starts and pressing
again stops the operation.
3. Fan speed button
4. Swing/Wind Direction button
5. Timer setting button
Use for operating with a timer.
6. Reset button
Use this button after changing the batteries.
7. Cover
Press at the top center and then slide down.
8. Transmitter
9. Remote control sensor
Detects the temperature at the remote
controller when detection has been switched
to the remote control by the sensor button.
10. Temperature setting buttons
raises the temperature setting 1 °C at
a time.
lowers the temperature setting 1 °C at
a time.
11. Filter button
CZ-RWSC2
Press to turn off the fi lter lamp on the
receiver.
12. Mode Select button
Press to switch the operation mode.
13. Ventilation button
Use this when connected to an aftermarket
fan. Pressing this button starts and stops the
fan. When the air conditioner is started or
stopped, the fan starts or stops at the same
time. (
appears on the display of the
remote control when the fan is operating.)
14. Address button
15. Sensor button
Use this when switching to detect the
temperature at the remote control. At
shipping the default setting is set to detect
the temperature at the unit. At this time
is
shown on the display.
16. Clock button
Use this when setting the clock.
REMOTE CONTROL
One remote control can control a group of up to eight indoor units.
(See Page EN-12)
From this page on the names of remote control
buttons will be abbreviated as the illustration of
the “button”.
E.g.: Start/Stop button Æ
EN-4
1. Receiver
Receives the signal sent from the remote
control.
2. Emergency operation button
Display lamps
When an error occurs, one of the lamps fl ashes. When a
display lamp is blinking, refer to “14. Before Requesting
Service”.
3. Operating lamp
This lamp is lit when the unit is operating.
4. Timer lamp
This lamp is lit when the timer is set.
5. Standby lamp
• When the heater is working, the lamp lights
at the following times. When the thermostat
has operated during defrosting at the time
of the startup.
• The lamp fl ashes when an error occurs.
6. Filter lamp
This lamp is for notifying you when the fi lter
needs to be cleaned.
7. Swing button
8. Normal/Stop All switch
Use in the Normal position. It does not
operate in the Stop All position.
Remote control, main / remote control,
secondary, switch
In normal use this should be on remote
control, main. It is also possible to use both
in conjunction with a wired remote control
(sold separately). (Consult with the dealer
where the product was purchased about
making the settings.)
Test/On switch
This is used during service. It is not for
normal use.
Test Run/On switch
This is used during service. It is not for
normal use.
9. Address switch
Differentiate between incoming and outgoing
signals.
Note
• If a heat pump model is being used, it will beep
twice and the operating lamp will light up on the
display; if the timer and standby lamps blink
alternately, a confl ict between the heating and
cooling exists, so the unit cannot operate in the
desired mode. (On models that do not have an
Auto function, even if Auto is selected, it works in
the same way.)
• When the local operation is disabled by such as
the centralized control, and if the Start, Stop, Mode
or Temperature setting buttons are pressed, the
unit will beep fi ve times and the change will not be
made.
Receiver
2. Names and Operations (Cont.)
3. Installing Batteries
EN-5
EN
1. Remove the cover.
2. Insert two AAA alkaline batteries.
Put the batteries in with the polarity [+/–] as shown in the
fi gure.
3. Gently insert one end of an unfolded paper clip
(or a similar object that can fi t) into the Reset hole
and press the reset button inside the hole and
then put the cover back on.
Note
• Change the batteries when the display of the remote control
gets weak or if it will not work unless close to the receiver.
(Alkaline batteries generally last about one year.)
• When changing batteries, always use two fresh batteries of the
same make.
• If the remote control will not be used for a long period of time,
remove the batteries.
• Please dispose of batteries appropriately.
• After changing the batteries, follow the procedures on the next
page to reset the current time.
HOW TO REMOVE BATTERIES
1. Remove the cover.
2. Press the battery toward the negative end and
lift it out by its positive end. (As shown at right)
3. Remove the other battery in the same way.
Note
• Dispose of the used batteries at the designated location in
compliance with the applicable local ordinances.
Warning
• Do not swallow the battery.
• After removing the battery from remote control unit, keep it away from the reach of children.
The battery can cause death by suffocation if swallowed.
• When inserting the battery, make sure the polarities (+ and -) are correct.
Reset hole
Cover
4. Setting the Current Time
EN-6
After changing the batteries and pressing reset, be sure to reset the
current time.
(When reset is pressed, the current time reverts to [
])
1. Press for two seconds or more.
Once the clock displays starts blinking, the clock can be set.
2. Set the hour with
/
of the .
If you press and hold the button, the time changes quickly.
3. Set the minutes with
/
of the .
If you press and hold the button, the time changes quickly.
4. Pressing completes the time setting.
• While you are setting the current time, the time display fl ashes but
the colon does not.
• If the buttons are not pressed for three minutes while setting the
current time, it is set to the displayed time.
Note
•
When reset is pressed, the timer settings are deleted.
2
1, 4
3
5. Operation
EN-7
EN
Power: Turn on the power of the indoor unit at least 14 hours
before operation.
1. Press
.
2. Press
and select from among Auto
,
Heat
,
Dry
,
Cool
and Fan .
3. Press
and select the desired speed.
If set to Auto , the fan speed switches automatically. (Auto does
not work when in the Fan mode.)
4. Press one of the buttons and set the desired
temperature.
Temperature settings cannot be made when in the Fan mode.
MAX MIN
Auto
27 17
Heat
26 16
Dry
/ Cool
30 18
Stop: Press .
When the unit is stopped with the remote control, even though the
compressor of the outdoor unit stops, the fan on the outdoor unit
may continue to run for a while.
Auto , Heat
, Dry
, Cool
, Fan
Models that only provide the cooling function cannot operate in the auto or heating modes.
1
4
2
3
EN-8
If the unit is not heating very effectively with a Low fan speed , switch the fan
speed to High or Medium.
Depending on the indoor unit being used, it may indicate a function that it does not have. (The fan
speed is set.)
If you cannot turn the air conditioner off in the normal way.
Disconnect the power to the indoor unit and contact the dealer where the product was purchased.
<Auto Operation>
If all the indoor units are identical in a cooling system and are under control as one group, it heats or
cools automatically via the differences between the set temperature and the room temperature.
<Dry Operation>
• Depending on the indoor unit used, the remote control may have a [Dry] indicator on its display
even though the unit does not have the Dry function. (Same as cooler operation)
• When the room temperature approaches the temperature setting, the unit continues to start up or
stop automatically.
• When the drying mode stops operating, the indoor unit’s fan blows a gentle breeze in order to keep
the moisture from returning to the room at a minimum.
• Depending on the indoor unit used, and/or the temperature in the room, the fan speed may not be
adjustable.
• Depending on the unit used, when the outside air temperature is 15 °C or less, the dry function will
not operate.
5. Operation (Cont.)
6. Timer Operation
EN-9
EN
• When setting the timer, make sure the current time on the remote control is accurate.
• The timer’s clock can only be set when the display of the remote control is ON.
• After setting the timer, put the remote control in a place where its signal will reach the receiver of the
indoor unit. (When the time set for the timer is reached, a signal is sent from the remote control to
Start/Stop the unit.)
Using the Timer
1. Press either
/ of the
or
, and while the time is
being displayed, if you press
/
again, a scheduled time can
be set.
The time last set on the timer is displayed.
“--:--“ indicates time to change the batteries.
2. Press either
/
of the
or and set the timer to the
desired time.
Every time you press
/
, the time changes in 10 minute increments.
If you press and hold the button, the time changes quickly.
3. After setting the timer, if you press , the time you set
changes to a steady display, indicating settings are complete.
After the timer setting is displayed for three seconds, the display reverts to
the current time.
1, 23
EN-10
Combining ON and OFF Timers
• Setting the ON and OFF timers, respectively.
Checking the timer setting
• If you press either / for the or the , the scheduled time is displayed for four
seconds.
• When no timer setting has been made, it displays --:--. (Initial Setting)
Changing a timer setting
• Press / for the or the , and then when the timer setting is displayed, press /
for the timer again.
Canceling a timer setting
• If you press [CANCEL], the timer setting is canceled.
• If you wish to cancel the setting for either the
or the timer, press / or the desired
timer and when the scheduled time is displayed, press [CANCEL].
Using the same timer setting every day
• If you press for 2 or more seconds, “ ” is displayed and the ON timer or the OFF timer will
operate the unit at the same time every day.
• If you press
fagain for two seconds or more, “ ” goes off and the timer operates just once.
6. Timer Operation (Cont.)
7. Adjusting the Wind Direction
EN-11
EN
Please face the fl ap (up-down wind
direction plate) downwards. If it faces
upwards, the warm air will not reach
the fl oor level.
In the Heat Mode
Please face the fl ap (up-down wind
direction plate) upwards. If the plate
faces downwards, condensation
may form and drip from around the
air outlet.
In the Cool and Dry Modes
In the Fan Mode In All Modes
Displays with Swing Stopped
Initial Setting
Initial Setting
Initial Setting
Moves Constantly
Fan/Heat Modes
Cool/Dry Modes
• Never try to manually move the fl ap (up-down wind direction plate) that is operated by the remote
control.
• When the unit stops, the fl ap (up-down wind direction plate) automatically faces downwards.
• When the unit is in heating standby, the fl ap (up-down wind direction plate) faces upward. Also,
bear in mind that the fl ap starts swinging after the heating standby mode is released, but the
display on the remote control indicates Auto Flap during standby heating as well.
CZ-RWSU2/CZ-RWST2/CZ-RWSL2/CZ-RWSY2/
Indoor Unit (CZ-RWSK2)
Setting the Wind Direction
While the unit is operating, every time you press , the
direction the fl ap faces changes.
Setting Flap to Swing
If you press to set the fl ap (up-down wind direction
plate) in its most downward facing position, and then
press
again, is displayed and the fl ap swings
automatically up and down.
Stopping Flap Swing
If you press again while the fl ap is swinging, you can
stop the fl ap from swinging and set it in place as desired.
Thereafter, if you press
, you can set the wind direction
starting from the most upward position.
• When the unit is in the Cool or Dry modes, the fl ap cannot
stop facing downwards. If you try to stop the fl ap from
swinging while it is facing downwards, it will continue
moving until it is in the third position from the top.
EN-12
CZ-RWSC2
The available functions differ depending on the indoor unit being used. The wind direction cannot
be set via remote control for any models other than those noted below. For more information, please
refer to the users’ manual that came with your indoor unit.
Four-direction Ceiling Cassette Models, Bi-directional Ceiling Cassette Models,
Unidirectional Cassette Models for High Ceilings, Ceiling Suspended Models, Wall
Models
Please refer to Setting the Wind Direction and Stopping Flap Swing.
8. Operating Multiple In/Outdoor Units Simultaneously
Group control works well for providing air
conditioning to one, large room with more
than one air conditioning units.
• One remote control can operate up to eight
indoor units.
• All the indoor units have identical settings.
• Set temperature sensing to the indoor unit (Main
Sensor). (See Pages I and II)
(Group Control)
Indoor Unit
Indoor Unit
Signal Line
Receiver
Wireless Remote Control
7. Adjusting the Wind Direction (Cont.)
9. Using the Remote Control
EN-13
EN
• Point the transmitter of the remote control at the receiver. When the signal is received correctly it will
beep once. (It beeps twice only when the unit starts operating.)
• The signal can be received at a distance of about 6 meters. This distance should be used only as a
guide. It depends on battery strength.
• Make sure nothing is between the remote control and the receiver that could block the signal.
• Do not leave the remote in direct sunlight, where the wind from the air conditioner can blow directly
on it, or near any other heat source.
• Take care not to drop, throw or wash the remote control with water.
• The signal from the remote control may not be received in rooms with rapid start fl uorescent
lighting, inverter lights, plasma displays, LCD televisions (monitor), etc. For more information, please
contact the dealer where the product was purchased.
Wall Mount Use
• Press from the location you wish to mount the remote and
make sure the signal is received correctly.
• Pull the remote control forward to remove it.
10. For Best Results
Don’t get the remote control too far away from the receiver.
This may cause a malfunction.
Be sure to keep the remote control in the same room as the receiver.
Point the remote control at the receiver.
When the signal is received correctly it will beep one time.
Avoid locating the remote control where it is covered, such as behind a curtain.
Keep it out in the open.
Fasten the remote
control mount with
screws.
Fitting the remote
control in the
mount.
Remote control
mount
Press
Put in
11. Addresses
EN-14
In both multi and single unit installations, when more than one indoor unit is installed in the same
room with a compatible remote control, addresses can be set up to avoid crosstalk.
By setting the address switches on the receivers and matching them with the number of addresses on
the remote control, up to six indoor units can be controlled separately with the remote control. (When
using units in a fl exible combination or operating multiple units simultaneously, as they are operated at
the same time, they cannot be controlled individually.)
There are separate address settings, receiver addresses for the receivers*
1
and transmitter addresses
for the remote control.
For more information, please contact the dealer where the product was purchased.
• The setting procedure is different for CZ-RWSY2 and Indoor Unit (CZ-RWSK2). (See Page EN-16)
• These settings are saved in nonvolatile memory in the remote control, so even when its batteries are
changed, the settings do not have to be made again.
*
1
CZ-RWST2 is of receivers (Inside the indoor unit); CZ-RWSL2 is of an operation panel. (Inside the
indoor unit)
Checking Addresses
When you press on the remote control, its current address is shown in the display. If this address
corresponds to the address of a receiver*
2
, the buzzer sounds. (If it is on ALL, the buzzer will always
sound.)
If it is on ALL, it can be operated regardless of receiver addresses. Point the remote control at the
receiver you wish to operate and transmit.
*
2
CZ-RWSL2 is a receiver (Indoor unit)
Matching up Addresses
Setting Remote Control Addresses
1. If you press
and at the same time, “ ” will blink.
2. While holding
down, every time you press , it cycles from ALLÆ1Æ2Æ3…
6ÆALL.
Set it to the receiver address switch of the indoor unit you wish to operate.
3. When you release , the address that was displayed is set.
When you do this, if it corresponds to the receiver’s address setting, the buzzer sounds.
EN-15
EN
Address
Display on the
Remote Control
•••••
CZ-RWSU2
Position of
receiver’s
(inside indoor
unit) address
switch
The position of the
receiver’s address
switch does not
matter.
•••••
For 1, 2 and 3, set the
switch on the right and for 4,
5 and 6, to the left.
CZ-RWST2
Position of
receiver’s
(inside indoor
unit) address
switch
The position of the
receiver’s address
switch does not
matter.
•••••
For 1, 2 and 3, set the
switch on the left and for 4,
5 and 6, to the right.
CZ-RWSL2
Position of
the operation
panel’s (inside
indoor unit)
address switch
The position of the
receiver’s address
switch does not
matter.
•••••
For 1, 2 and 3, set the
switch on the left and for 4,
5 and 6, to the right.
CZ-RWSC2
Position of
the Receiver’s
Address Switch
The position of the
receiver’s address
switch does not
matter.
•••••
For 1, 2 and 3, set the
switch on the left and for 4,
5 and 6, to the right.
EN-16
Setting Addresses (CZ-RWSY2/CZ-RWSK2)
(Setting the address of the indoor unit)
1. First of all, set the address for the remote control with Setting Remote Control Address
(See Page EN-14).
2. Press [Emergency Operation]
of the indoor unit for four seconds or more.
When you do this, the lamps of the display will blink one after another.
3. Press on the remote control.
4. The buzzer will sound and the address of the indoor unit will change to the address
displayed on the remote control.
5. If you press [Emergency Operation]
of the indoor unit once, the lamps on the indoor
unit’s display will turn off.
Note
• Please do not hold the [Emergency Operation]
button of the indoor unit down while the indoor unit’s
display lamps are blinking one after another.
• Make sure to operate while the indoor unit is stopped.
• The address of indoor unit is set to "ALL" at the time of the shipment.
11. Addresses (Cont.)
12. Emergency Operation
EN-17
EN
Use [Emergency Operation] in the following situations when there is an urgent need.
• When the remote control’s batteries have failed.
• When the remote control is broken.
• When the remote control is lost.
*
1
Figures: CZ-RWSU2, CZ-RWSY2 and CZ-RWST2 are of receivers (inside indoor unit), CZ-RWSL2 is
of the operation panel (inside indoor unit) and Indoor Unit (CZ-RWSK2) is of its front panel.
CZ-RWST2
Start/Stop
Indoor Unit (CZ-RWSK2)
Start/Stop
CZ-RWSU2/CZ-RWST2/CZ-RWSY2/Indoor Unit (CZ-RWSK2)
Start: press [Emergency Operation] of the receiver.
If the indoor temperature is 24 °C or greater when the unit starts running, it will act as a cooler.
If the indoor temperature is less than 24 °C when the unit starts running, it will act as a heater.
Stop: press [Emergency Operation] of the receiver again.
Start/Stop
CZ-RWSU2
Start/Stop
CZ-RWSY2
EN-18
Note
• The Test Run/On and Test/On switches are for use when the unit is installed and test run. It is not for normal
use.
• If the [Normal/Stop ALL] switch is on
Stop ALL, the unit cannot receive signals from the remote control.
CZ-RWSC2/CZ-RWSL2
1. Press [Emergency Operation] of the receiver.
If the indoor temperature is 24 °C or greater when the unit starts running, it will act as a cooler.
If the indoor temperature is less than 24 °C when the unit starts running, it will act as a heater.
2. If you press , the wind direction automatically oscillates up and down.
Stop: press [Emergency Operation]
of the receiver again.
21
CZ-RWSL2 CZ-RWSC2
1
2
Note
• The Test Run/On and Test/On switches are for use when the unit is installed and test run. It is not for normal
use.
• If the [Normal/Stop ALL] switch is on
Stop ALL, the unit cannot receive signals from the remote control.
12. Emergency Operation (Cont.)
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
Panasonic CZRWSU2 Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic CZRWST2 Owner's manual
-
-
-
-
-
-
Panasonic CZRWSD2 Operating instructions
-
-
-
Other documents
-
Haier 2HUM14H03/R2(DB) Operating instructions
-
-
-
Toshiba RAV-SM1100UT-E User manual
-
Sanyo SAP-CMV2441G Technical & Service Manual
-
-
-
-
-