Whirlpool WIDXL 126 (UK) User manual

Brand: Whirlpool

Model: WIDXL 126 (UK)

Category: Washing machines

Type: User manual

This manual is also suitable for

WIDXL 126

English,1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Electric and water connections

The first wash cycle

Technical details

Washer-dryer description, 6-7

Control panel

Leds

Starting and Programmes, 8

Briefly: how to start a programme

Programme table

Personalisations, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser

Preparing your laundry

Special items

Precautions and advice, 11

General safety

Disposal

Saving energy and respecting the environment

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning your appliance

Cleaning the detergent dispenser

Caring for your appliance door and drum

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Service, 14

Before calling for Assistance

WASHER-DRYER

WIDXL 126

Instructions for use

,15

Installation

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washer-dryer to inform the

new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washer-dryer.

2. Check whether the washer-dryer has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the four

protective screws and

the rubber bush with the

respective spacer,

situated on the rear of

the appliance (see also

the installation leaflet).

NB:The plastic spacers

may fall down inside the

machine once the bolt

has been removed, and will not interfere with the

operation of the machine.

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of noise

if the two front feet have not been adjusted correctly.

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washer-dryer.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth (see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washer-dryer,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

 Ensure that the supply taps are allowing water

through. Old taps may seize in the closed position

and thus prevent water reaching the machine.

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

The drain hose may be

connected to an

under-sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends

have been taken off

the spigot.

If it is place over the

edge of a basin or sink

be sure the free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed down

too far, this may cause the machine to self -syphon

ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

 the supply voltage is included within the values

indicated on the Technical details table

(see page 5);

 the socket is compatible with the washer-dryer's

plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects

to the waste water

pipe cut end off

spigot or remove the

blanking cap

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng

the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible

to the plug body and dispose of it as described

above.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

Technical details

Model

WIDXL 126

Dimensions

59.5 cm wide

85 cm high

53.5 cm deep

Capacity

from 1 to 6 kg for the wash programme;

from 1 to 4 kg for the drying programme

Electric

connections

please refer to the technical data plate

fixed to the machine

Wate r

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rpm

Control

programmes

according to

EN 50229

directive

Wash: programme 2; temperature 60°C;

run with a load of 6 kg.

Drying: first drying cycle performed with

a 2 kg load and the DRYING knob on

the setting;

Second drying cycle performed with a 4

kg load and the DRYING knob on the

setting.

This appliance is compliant with the

following European Community

Directives:

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 2002/96/CE

- 2006/95/CE (Low Voltage)

Washer-dryer description

Control panel

Detergent dispenser

ON-OFF

Button

START/RESET

Button

TEMPERATURE

Knob

PROGRAMME

Knob

Leds

FUNCTION

Buttons

ON-OFF/

DOOR

LOCK

Led

Detergent dispenser: to add detergent and fabric

softener (see page 10).

LEDS: to find out the wash cycle progress.

If the Delay Timer function has been set, the time

left until the programme starts will be indicated (see

page 7).

DRYING knob: to set the desired drying cycle

(see page 9).

FUNCTION buttons: to select the functions

available. The button corresponding to the function

selected will remain on.

TEMPERATURE knob: to set the temperature or

the cold wash cycle (see page 9).

START/RESET button: to start the programmes or

cancel any incorrect settings.

ON-OFF/DOOR LOCK Led: to find out whether the

Washer-dryer is on and if the appliance door can be

opened (see page 7).

ON/OFF button: to turn the Washer-dryer on and off.

PROGRAMME knob: to select the wash

programmes. The knob stays still during the cycle.

DRYING

Knob

ON-OFF/DOOR LOCK led:

If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any

damages, wait for the LED to flash before you open the appliance door.

 The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED

indicates there is an abnormality. Call for Technical Assistance (see page 13).

Cycle progress:

During the wash cycle, the LEDs gradually illumina-

te on to indicate the cycle progress:

Prewash / Wash

Rinse

Spin cycle

Drying

Note:

- during draining, the LED corresponding to the

Spin cycle phase will be turned on.

- when the drying cycle is complete, the indicator

light relative to phase

will flash, to indicate that

the DRYING knob needs to be set back to the 0

setting.

Function buttons

The FUNCTION BUTTONS also act like LEDS.

When a function is selected, the corresponding

button is illuminated.

If the function selected is incompatible with the

programme set, the button will flash and the

function will not be enabled.

If you set a function that is incompatible with

another function you selected previously, only the

last one selected will be enabled.

Leds

The LEDS provide important information.

This is what they can tell you:

Delay set:

If the Delay Timer function has been enabled (see

page. 9), once you have started the programme,

the LED corresponding to the delay set will begin to

flash:

As time passes, the remaining delay will be

displayed, and the corresponding LED will flash:

Once the set delay is complete, the flashing LED will

turn off and the programme set will start.

Type of fabric and

degree of soil

Prog. Temp.

Drying

Cycle

Detergent

Fabric

softener

Cycle

length

(m in utes)

Max. Spin

Speeds

(r.p.m .)

Description of wash cycle

pre-

wash

Standard

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C    

155 Max.

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C   

150 Max.

Wash cycle, rinse cycles, intermediate and

final spin cycles

Heavily soiled whites and fast

colours

60°C   

140 Max.

Wash cycle, rinse cycles, intermediate and

final spin cycles

Heavily soiled whites and

delicate colours

40°C   

125 Max.

Wash cycle, rinse cycles, intermediate and

final spin cycles

Slightly soiled whites and

delicate colours (shirts,

jumpers, etc.)

40°C   

85 Max.

Wash cycle, rinse cycles, intermediate and

final spin cycles

Heavily soiled fast colours

(baby linen, etc.)

0°C



72 800

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Heavily soiled fast colours

(baby linen, etc.)

40°C   

70 800

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Wool

40°C  

50 600

Wash cycle, rinse cycles, delicate spin

cycle

Very delicate fabrics

(curtains, silk, viscose, etc.)

30°C  

45 no

Wash cycle, rinse cycles, anti-crease

or draining cycle

Drying cotton



Max.

Drying delicates



Tim e 4 y ou

Heavily soiled whites and fast

colours

60°C  

60 Max.

Wash cycle, rinse cycles, intermediate and

final spin cycles

Delicate colours (all types of

slightly soiled garments)

°C



40 800

Wash cycle, rinse cycles, delicate spin

cycle

Delicate colours (all types of

slightly soiled garments)

30°C    30

800

Wash cycle, rinse cycles and delicate

spin cycle

Sport

Sports shoes

(MAX. 2 pairs)

°C

 50

800

Cold wash (without detergents), wash

cycle, rinse cycles, and delicate spin cycle

Fabrics for sportswear

(Tracksuits, shorts, etc.)

30°C   60

600

Wash cycle, rinse cycles, intermediate and

final spin cycles

PARTIAL PROGRAMMES

Rinse  

800

Rinse cycles and spin cycle

Spin cycle 

800

Draining and spin cycle

Drain

Starting and Programmes

Programme table

Notes

-For programme 9, we advise against exceeding a wash load of 3.5 kg.

-For programme 13 we advise against exceeding a wash load of 2 kg.

-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.

Special programme

Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts

30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash

different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

Briefly: starting a programme

1. Switch the Washer-dryer on by pressing button .

All the LEDS will light up for a few seconds and

the ON-OFF/DOOR LOCK Led will begin to flash.

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the PROGRAMME knob to the programme

required.

4. Set the wash temperature (see page 9).

5. Set the drying cycle if necessary (see page 9).

6. Add the detergent and any fabric softener (see page 10).

7. Start the programme by pressing the START/RESET

button for one second. Once the programme has

been accepted all of the option and status LED's

will illuminate momentarily, the Door Lock LED

will be lit and the relevant wash cycle progress

LED will also be lit.

To cancel it, keep the START/RESET button pressed

for at least 2 seconds.

8. When the programme is finished, the ON-OFF/

DOOR LOCK Led will flash to indicate that the

appliance door can be opened. Take out your

laundry and leave the appliance door ajar to allow

the drum to dry thoroughly. Turn the Washer-dryer

off by pressing button

Personalisations

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).

The temperature can be lowered, or even set to a cold wash (

Set the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: From 40 minutes to 150.

B - Based on the damp level of the dry clothes:

Iron

: slightly damp clothes, easy to iron.

Hanger

: dry clothes to put away.

Cupboard

: very dry clothes, recommended for towelling

and bathrobes.

A cooling stage is foreseen at the end of the drying cycle.

If your laundry load to wash and dry is exceptionally in excess

of the maximum load foreseen (see table opposite), perform

the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the

drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.

Dry only

Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the

desired drying type using the DRYING knob.

Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of

dryness (Cupboard

, Hanger , Iron ).

- For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;

2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the

programme set.

Function Effect Comments

Enabled with

programmes:

D elay T im er

Delays the start

of the wash by

up to 9 hours.

Press the button repeatedly until the LED corresponding to the

desired delay is turned on.

The fifth time the button is pressed, the function will be disabled.

N.B.: Once you have pressed the Start/Reset button, the delay

can only be decreased if you wish to modify it.

All

Eas y iro n

This option

reduces the

amount of

creasing on

fabrics, making

them easier to

iron.

When this function is set, programmes 4, 6 will end with the

laundry left to soak (Anti-crease) and the Rinse cycle phase

LED will flash.

- to conclude the cycle, press the START/RESET button;

- to run the draining cycle alone, set the knob to the relative

symbol and press the START/RESET button.

3, 4, 6,

9, 10,

Rinse cycle.

Ex t ra R in se

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large

quantities of detergent.

1, 2, 3, 4, 9,

10, 12, 13,

Rinse cycle.

1200-600

Reduces the

spin speed.

All

programmes

except for 6

and draining.

Fabric

type

Load type Max.

load

(kg) Cup-

board

Hanger Iron

Cotton,

Linen

Clothing of different sizes

4 130 120 110

Cotton Terry towels

4 130 120 110

Terit al,

Cotton

Sheets, Shirts

2,5 90 80 70

Acrylics Pyjamas, socks, etc.

165 6060

Nylon Slips, tights, stockings, etc.

165 6060

Table of drying times

The data contained in the

table are purely indicative.

 The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the final spin

speed if an unbalanced load is detected.

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

 Do not use hand wash detergent because it may

form too much foam.

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 6 kg

Synthetic fabrics: max 2.5 kg

Delicate fabrics: max 2 kg

Wool: max 1,5 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme 6

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Wool: for best results, use a specific detergent,

taking care not to exceed a load of 1,5 kg.

Detergents and laundry

Precautions and advice

 The Washer-dryer was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the

environment. The crossed out "wheeled bin"

symbol on the product reminds you of your

obligation, that when you dispose of the appliance

it must be separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Ariston

technology, your washing machine only needs less

than half the amount of water to get the best results:

an objective reached to respect the environment.

Saving on detergent, water, energy and time

 To avoid wasting resources, the Washer-dryer

should be used with a full load. A full load instead

of two half loads allows you to save up to 50% on

energy.

 The pre-wash cycle is only necessary on extremely

soiled garments. Avoiding it will save on detergent,

time, water and between 5 and 15% energy.

 Treating stains with a stain remover or leaving

them to soak before washing will cut down the

need to wash them at high temperatures.

A programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on energy.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

The Delay Timer option (see page 9) helps to

organise your wash cycles accordingly.

 If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning pump

that does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into

the pre-chamber that protects the pump, situated in

the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

Washer-dryer (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

Troubleshooting

Your washer-dryer could fail to work. Before calling for Assistance (see page 14), make sure the problem can't

easily be solved by consulting the following list.

Problem

The washer-dryer won't start.

The washer-dryer does not fill

with water.

The machine continuously fills

and empties with water.

The washer-dryer does not

drain or spin.

The washer-dryer vibrates too

much during the spin cycle.

The washer-dryer leaks.

The ON-OFF/DOOR LOCK Led

flashes rapidly at the same

time as at least one other LED.

There is too much foam.

The washer-dryer does not dry.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 The

button has not been pressed.

 The START/RESET button has not been pressed.

NB: It should be held minimum one second.

 The water tap is not turned on.

 A delayed start has been set (using the Delay Timer, see page 9).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/RESET button has not been pressed.

 The drain hose is too low or too far in to the stand pipe (see page 3) for correct installation.

 The wall drainage system doesn't have a standard pipe (min. 38 mm).

 Some programs have a slower final spin to taked best care of the

fabrics. See page 8 for details of the final spin speed for each program.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 8).

 The Easy iron option is enabled: to complete the programme, press

the START/RESET button (see page 9).

 The drain hose is bent (see page 3).

 Remove the drain hose from the standpipe or under-sink trap and check for

blockages, ensuring that the water can drain freely away from the machine.

 When the machine is installed, the locking screws for the oscillating

assembly are still in place. Remove the screws (see page 2).

 The washer-dryer is not level (see page 2).

 The washer-dryer is closed in between furniture cabinets and the wall (see page 2).

 The water inlet hose is not screwed on correctly (see page 2).

 The detergent dispenser is obstructed (to clean it, see page 12).

 The drain hose is not secured properly (see page 3).

 This means there is a problem with the machine. Before calling

Assistance, please follow the set of instructions below:

1. Switch off the machine;

2. Remove the plug connecting the appliance to the mains supply

and wait for at least 40 seconds;

3. Place the plug back into the socket;

4. Switch on the machine;

5. If the problem is still evident after this process has been carried out,

contact Assistance.

 The detergent is not suitable for machine washing (it should bear the

definition "for washing machines" or "hand and machine wash", or the like).

 You used too much detergent.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A delayed start has been set (using the Delay Timer, see page 9).

 the DRYING knob is on the 0 setting.

Before calling for Assistance:

 Check whether you can solve the problem on your own (see page 13);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 If the machine has been installed or used incorrectly, you may be charged for the maintenance callout

service.

 Always request the assistance of authorised servicemen.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washer-dryer.

Service

ﻲﺑﺮﻋ

لﺎﻤﻌﺘﺳ ﻻا ﻞﺟأ ﻦﻣ تﺎﻤﻴﻠﻌﺗ

ﺲﺑ ﻼﻣ ﺔﻓﺎﺸﻧ ﺔﻟﺎﺴﻏ

WIDXL 126

ﻲﺑﺮﻋ

اﻟﻔﻬﺮس

اﻟﺘﺮآﻴﺐ 61 - 71 - 81 - 91

اﺧﺮاج اﻟﺠﻬﺎز ﻣﻦ ﺗﻐﻠﻴﻔﻪ و ﺗﺴﻮﻳﺔ اﻟﺠﻬﺎز، 61

ﺗﻮﺻﻴﻼ ت اﻟﻤﺎء واﻟﻬﺮﺑﺎء، 61 - 71

أول دورة ﻏﺴﻴﻞ، 81

ﻣﻮاﺻﻔﺎت ﻓﻨﻴﺔ، 91

وﺻﻒ ﻏﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ اﻟﻤﻼ ﺑﺲ 12-02

ﻟﻮﺣﺔ اﻟﻘﻴﺎدة، 02

ﺻﺎﺑﻴﺢ اﻧﺬار، 12

اﻟﺘﺸﻐﻴﻞ و اﻟﺒﺮﻣﺠﺔ، 22

ﺑﺒﺴﺎﻃﺔ: ﺗﺸﻐﻴﻞ ﺑﺮﻧﺎﻣﺞ، 22

ﻟﻮﺣﺔ اﻟﺒﺮاﻣﺞ، 22

ﺗﺸﺨﻴﺺ، 32

وﺿﻊ درﺟﺔ اﻟﺤﺮارة؛ 32

وﺿﻊ ﻋﻤﻠﻴﺔ اﻟﺘﻨﺸﻴﻒ، 32

وﻇﺎﺋﻒ، 32

ﻣﺴﺎﺣﻴﻖ ﻏﺴﻴﻞ و ﻣﻼ ﺑﺲ، 42

ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ، 42

دورة اﻟﺘﺒﻴﺾ، 42

ﺗﺤﻀﻴﺮ اﻟﻤﻼ ﺑﺲ ﻟﻠﻐﺴﻴﻞ، 42

أﻗﻤﺸﺔ ﺧﺎﺻﺔ، 42

ﺣﺬر وﻧﺼﺎﺋﺢ، 52

أﻣﻦ ﻋﺎم، 52

اﻟﺘﺨﻠﺺ ﻣﻦ اﻟﻨﻔﺎﻳﺎت، 52

اﻻ ﻗﺘﺼﺎد و واﺣﺘﺮام اﻟﺒﻴﺌﺔ، 52

ﺻﻴﺎﻧﺔ و ﺣﻤﺎﻳﺔ، 62

اﻏﻼ ق اﻟﻤﺎء و اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ، 62

ﺗﻨﻈﻴﻒ ﻏﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ اﻟﻤﻼ ﺑﺲ، 62

ﺗﻨﻈﻴﻒ ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ، 62

ﺣﻤﺎﻳﺔ ﺑﺎب اﻟﻐﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ و ﺣﻮض ﻏﺴﻴﻞ اﻟﻐﺴﺎﻟﺔ، 62

ﺗﻨﻈﻴﻒ ﻣﻀﺨﺔ ﺗﻔﺮﻳﻎ اﻟﻐﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ ﻣﻦ اﻟﻤﺎء، 62

ﻓﺤﺺ ﺧﺮﻃﻮم ﺗﻐﺬﻳﺔ اﻟﻐﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ ﺑﺎﻟﻤﺎء، 62

ﺣﺼﻮل ﺑﻌﺾ اﻟﻤﺸﺎآﻞ وﺣﻠﻮل ﻟﻬﺎ، 72

اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ، 82

لﺎﻤﻌﺘﺳ ﻻا ﻞﺟأ ﻦﻣ تﺎﻤﻴﻠﻌﺗ

! ﻣﻦ اﻟﻤﻬﻢ اﻟﺤﻔﺎظ ﻋﻠﻰ هﺬا اﻟﻜﺘﻴﺐ ﻟﻴﻤﻜﻨﻜﻢ اﻟﻌﻮدة اﻟﻴﻪ ﻋﻨﺪ اﻟﺤﺎﺟﺔ اﻟﻰ اﻟﺘﻌﺮف

ﻋﻠﻰ ﻣﻌﻠﻮﻣﺎت ﻋﻦ اﻟﺠﻬﺎز ﻓﻲ أي ﻟﺤﻈﺔ، ﻓﻲ ﺣﺎﻟﺔ ﺑﻴﻊ اﻟﺠﻬﺎز أو اﻋﻄﺎءه آﻬﺪﻳﺔ أو

ﻋﻨﺪ ﻧﻘﻞ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎن ﻻ ﺧﺮ، ﺗﺄآﺪوا ﻣﻦ أن ﻳﺒﻘﻰ هﺬا اﻟﻜﺘﻴﺐ ﻧﻊ اﻟﺠﻬﺎز وذﻟﻚ

ﻟ

ﺘ

ﻘ

ﺪﻳ

ﻢ ﻣ

ﻌ

ﻠ

ﻮﻣ

ﺎت ﺗ

ﺘ

ﻌ

ﻠ

ﻖ ﺑ

ﺘ

ﺸ

ﻌ

ﻴ

ﻞ وﺑ

ﺮﻣ

ﺠ

ﺔ اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﺎﻻ ﺿ

ﺎﻓ

ﺔ اﻟ

ﻰ اﻟ

ﻨ

ﺼ

ﺎﺋ

ﺢ واﻟ

ﺘ

ﺤ

ﺬﻳ

ﺮ

ﻟﻠﻤﺎﻟﻚ اﻟﺠﺪﻳﺪ ﻟﻠﺠﻬﺎز.

! أﻗ

ﺮؤوا ﺑ

ﺘ

ﻤ

ﻌ

ﻦ اﻟ

ﺘ

ﻌ

ﻠ

ﻴ

ﻤ

ﺎت: ﻓ

ﻲ داﺧ

ﻞ ه

ﺬا اﻟ

ﻜ

ﺘ

ﻴ

ﺐ ﻣ

ﻮﺟ

ﻮد ﻣ

ﻌ

ﻠ

ﻮﻣ

ﺎت ه

ﺎﻣ

ﺔ ﺗ

ﺘ

ﻌ

ﻠ

ﻖ

ﺑﺎﻟﺘﺮآﻴﺐ، اﻻ ﺳﺘﻌﻤﺎل، وأﻣﻦ اﻟﺠﻬﺎز.

اﺧﺮاج اﻟﺠﻬﺎز ﻣﻦ ﺗﻐﻠﻴﻔﻪ وﺗﺴﻮﻳﺔ اﻟﺠﻬﺎز

اﺧﺮاج اﻟﺠﻬﺎز ﻣﻦ ﺗﻐﻠﻴﻔﻪ

1. اﺧﺮﺟﻮا اﻟﻐﺴﺎﻟﺔ اﻟﻨﺸﺎﻓﺔ ﻣﻦ ﺗﻐﻠﻴﻔﻬﺎ

2. ﺗﺄآﺪوا ﻣﻦ اﻟﻐﺴﺎﻟﺔ اﻟﻨﺸﺎﻓﺔ ﻟﻢ ﻳﺤﺪث ﻟﻬﺎ أﺿﺮار ﺧﻼ ل ﺷﺤﻨﻬﺎ وﻧﻘﻠﻬﺎ ﻣﻦ ﻣﻜﺎن

ﻻ ﺧﺮ، اذا آﺎن اﻟﺠﻬﺎز ﻣﻀﺮر أو ﻣﻀﺮوب ﻓﻲ ﻣﻜﺎن ﻣﺎ ﻻ ﺗﻘﻮﻣﻮا ﺑﻌﻤﻠﻴﺔ ﺗﻮﺻﻴﻠﻪ

أو ﺗﺮآﻴﺒﻪ، واﺗﺼﻠﻮا ﺑﺎﻟﺒﺎﺋﻊ.

3. اﺧ

ﻠ

ﻌ

ﻮا اﻷ رﺑ

ﻊ ﺑ

ﺮاﻏ

ﻲ اﻟ

ﺘ

ﻲ ﺗ

ﺤ

ﻤ

ﻲ

اﻟﺠﻬﺎز ﺧﻼ ل ﻋﻤﻠﻴﺔ اﻟﻨﻘﻞ، وآﺬﻟﻚ اﺧﻠﻌﻮا

اﻟ

ﻘ

ﻄ

ﻊ اﻟ

ﻤ

ﻄ

ﺎﻃ

ﻴ

ﺔ وﻣ

ﺒ

ﺎﻋ

ﺪ آ

ﻞ واﺣ

ﺪة ﻣ

ﻦ

ﺬه، اﻟ

ﺘ

ﻲ ﺗ

ﻜ

ﻮن ﻣ

ﻮﺟ

ﻮدة ﻓ

ﻲ اﻟ

ﻤ

ﻨ

ﻄ

ﻘ

ﺔ

اﻟﺨﻠﻔﻴﺔ ﻣﻦ اﻟﺠﻬﺎز )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

4. اﻏﻠﻘﻮا اﻟﺜﻘﻮب ﺑﻮاﺳﻄﺔ اﻷ ﻏﻄﻴﺔ اﻟﺒﻼ ﺳﺘﻴﻜﻴﺔ اﻟﺘﻲ ﺗﻜﻮن ﻣﺰودة ﻣﻊ اﻟﺠﻬﺎز.

5. أﻏ

ﻠ

ﻘ

ﻮا ﺑ

ﺎﻷ ﻏ

ﻄ

ﻴ

ﺔ اﻟ

ﺘ

ﻲ ﺗ

ﻜ

ﻮن ﻣ

ﺰودة ﻣ

ﻊ اﻟ

ﺠ

ﻬ

ﺎز اﻟ

ﺜ

ﻼ ث ﺛ

ﻘ

ﻮب ﺣ

ﻴ

ﺚ ﻳ

ﻜ

ﻮن

ﻣ

ﻮﺿ

ﻮع ﻗ

ﺎﺑ

ﺲ اﻟ

ﺘ

ﻴ

ﺎر اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ )اﻟ

ﺬآ

ﺮ( اﻟ

ﺬي ﻳ

ﻜ

ﻮن ﻣ

ﻮﺟ

ﻮد ﻓ

ﻲ ﺧ

ﻠ

ﻒ اﻟ

ﺠ

ﻬ

ﺎز

ﻣﻦ اﻷ ﺳﻔﻞ ﻋﻠﻰ اﻟﻴﻤﻴﻦ.

6. ﺣﺎﻓﻈﻮا ﻋﻠﻰ ﺟﻤﻴﻊ اﻟﻘﻄﻊ اﻟﺘﻲ ﺗﻢ ﻓﻜﻬﺎ: ﻋﻨﺪ ﻧﻘﻞ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎن ﻻ ﺧﺮ ﻳﺠﺐ

ﺗﺮآﻴﺐ هﺬه اﻟﻘﻄﻊ ﻣﻜﺎﻧﻬﺎ ﻣﻦ ﺟﺪﻳﺪ.

! ﻳﺠﺐ ﻋﺪم ﺗﺮك اﻷ ﻃﻔﺎل اﻟﻠﻌﺐ ﺑﺘﻐﻠﻴﻒ اﻟﺠﻬﺎز.

ﺗﺴﻮﻳﺔ اﻟﺠﻬﺎز

1. رآﺒﻮا ﻏﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ اﻟﻤﻼ ﺑﺲ ﻋﻠﻰ أرﺿﻴﺔ ﻣﺴﺘﻮﻳﺔ وﺻﻠﺒﺔ ﺑﺪون أرﺗﻜﺎزهﺎ ﻋﻠﻰ

ﺣﺎﺋﻂ أو ﻗﻄﻊ أﺛﺎث أو أي ﺷﻲء اﺧﺮ.

2. اذا آ

ﺎﻧ

ﺖ اﻷ رﺿ

ﻴ

ﺔ ﻏ

ﻴ

ﺮ ﻣ

ﺴ

ﺘ

ﻮﻳ

ﺔ،

ﻳ

ﻤ

ﻜ

ﻨ

ﻜ

ﻢ اﻻ ﺳ

ﺘ

ﻌ

ﺎﻧ

ﺔ ﺑ

ﺎﻷ رﺟ

ﻞ اﻷ ﻣ

ﺎﻣ

ﻴ

ﺔ

اﻟﻤﺘﺤﺮآﺔ واﻟﺘﻲ ﻗﺎﺑﻠﺔ اﻟﺘﻌﺪﻳﻞ ﻓﻲ ارﺗﻔﺎﻋﻬﺎ

وذﻟﻚ ﻻ زاﻟﺔ ﻋﺪم اﺳﺘﻮاء اﻷ رﺿﻴﺔ )اﻇﺮ

اﻟﻰ اﻟﺸﻜﻞ(. زاوﻳﺔ اﻟﻤﻴﻼ ن اﻟﺘﻲ ﻳﻤﻜﻨﻜﻢ

ﻗﻴﺎﺳﺘﻬﺎ ﻋﻠﻰ اﻟﺴﻄﺢ اﻟﻌﻠﻮي ﻟﻠﺠﻬﺎز ﻳﺠﺐ

أن ﻻ ﻳﺰﻳﺪ ﻋﻦ 2 درﺟﺔ.

وﺿ

ﻊ اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﺸ

ﻜ

ﻞ ﻣ

ﺴ

ﺘ

ﻮي ﺗ

ﻌ

ﻤ

ﻞ ﻋ

ﻠ

ﻰ ﺛ

ﺒ

ﺎت اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﻤ

ﻜ

ﺎﻧ

ﻪ وﻋ

ﺪم ذﺑ

ﺬﺑ

ﺘ

ﻪ، وﻋ

ﺪم

ﺳﻤﺎع اﺻﻮات ﻣﺰﻋﺠﺔ ﺧﻼ ل ﻋﻤﻞ اﻟﺠﻬﺎزأو ﺗﺤﺮك اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎﻧﻪ ﺧﻼ ل ﻋﻤﻞ

اﻟﺠﻬﺎز، ﻓﻲ ﺣﺎﻟﺔ وﺟﻮد ﻣﻜﻴﺖ أو ﺳﺠﺎد ﻋﻠﻰ اﻷ رﺿﻴﺔ ﺗﺤﺖ اﻟﺠﻬﺎز ﻋﻴﺮوا اﻷ رﺟﻞ

ﺗ

ﺤ

ﺖ اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﺤ

ﻴ

ﺖ ﻳ

ﺘ

ﻢ ﺗ

ﺮك ﻣ

ﺴ

ﺎﻓ

ﺔ ﺑ

ﻴ

ﻦ اﺟ

ﻬ

ﺎز واﻷ رﺿ

ﻴ

ﺔ ﺗ

ﺤ

ﺘ

ﻪ وذﻟ

ﻚ ﻟ

ﺘ

ﺮك ﺣ

ﻴ

ﺰ

ﻟﺪﺧﻮل اﻟﻬﻮاء ﻣﻦ أﺟﻞ اﻟﺘﻬﻮﻳﺔ.

ﺗﻮﺻﻴﻞ اﻟﻤﺎء واﻟﻜﻬﺮﺑﺎء ﺑﺎﻟﺠﻬﺎز

ﺗﻮﺻﻴﻞ ﺧﺮﻃﻮم ﺗﻐﺬﻳﺔ اﻟﺠﻬﺎز ﺑﺎﻟﻤﺎء

1. أدﺧﻠﻮا ﺣﻠﻘﺔ ﻋﺪم ﺗﺴﺮب اﻟﻤﺎء اﻟﻤﺸﺎر

ﻟﻬﺎ ﺑﺎﻟﺤﺮف A ﻓﻲ ﻧﻬﺎﻳﺔ ﺧﺮﻃﻮم وارﺑﻄﻮه

ﺑﻨﺤﺒﺲ ﻣﺎء ﺑﺎرد ﺑﻔﺘﺤﺔ ﻣﺴﻨﻨﻪ ﺑﺴﻦ 3/4

ﻏﺎز )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

ﻗﺒﻞ وﺻﻠﻪ ﺑﺎﻟﺠﻬﺎز اﺗﺮآﻮا اﻟﻤﺎء ﻳﺨﺮج

ﻣﻦ اﻟﻤﺤﺒﺲ ﺣﺘﻰ ﺧﺮوج ﻣﺎء ﺻﺎﻓﻴﺔ ﻣﻦ

اﻟﻤﺤﺒﺲ.

2. اﺷﺒﻜﻮا اﻟﺨﺮﻃﻮم اﻟﺬي ﻳﻐﺬي اﻟﻐﺴﺎﻟﺔ

اﻟﻨﺸﺎﻓﺔ ﺑﺎﻟﻤﺎء وذﻟﻚ ﺑﺮﺑﻄﻪ ﺑﻤﺪﺧﻞ اﻟﻤﺎء

اﻟ

ﻤ

ﻮﺟ

ﻮد ﻓ

ﻲ ﻇ

ﻬ

ﺮ اﻟ

ﻐ

ﺴ

ﺎﻟ

ﺔ ﻣ

ﻦ اﻟ

ﺨ

ﻠ

ﻒ

ﻓ

ﻲ اﻟ

ﻤ

ﻨ

ﻄ

ﻘ

ﺔ اﻟ

ﻌ

ﻠ

ﻴ

ﺎ ﻋ

ﻠ

ﻰ اﻟ

ﻴ

ﻤ

ﻴ

ﻦ.)اﻧ

ﻈ

ﺮ

اﻟﻰ اﻟﺸﻜﻞ(

3. ﺧ

ﺬوا ﺣ

ﺬرآ

ﻢ ﻣ

ﻦ ﻻ ﻳ

ﻜ

ﻮن اﻟ

ﺨ

ﺮﻃ

ﻮم ﻣ

ﻄ

ﻮي أو ﻣ

ﺨ

ﻨ

ﻮق ﻓ

ﻲ ﻣ

ﻜ

ﺎن ﻣ

ﺎ ﻋ

ﻠ

ﺔ

ﻃﻮل اﻣﺘﺪاده.

! ﺿﻐﻂ ﺷﺒﻜﺔ اﻟﻤﺎء ﻳﺠﺐ أن ﺗﻜﻮن ﺑﺎﻟﻘﻴﻢ اﻟﺘﻲ ﺗﻜﻮن ﻣﻌﻄﻴﺔ وﻣﻜﺘﻮﺑﺔ ﻻ ﺋﺤﺔ اﻟﺨﺼﺎﺋﺺ

اﻟﻔﻨﻴﺔ ﻟﻠﺠﻬﺎز)اﻧﻈﺮ اﻟﻰ اﻟﺼﻔﺤﺔ اﻟﺠﺎﻧﺒﻴﺔ(

! اذا آﺎن ﻃﻮل ﺧﺮﻃﻮم ﺗﻐﺬﻳﺔ اﻟﻐﺴﺎﻟﺔ اﻟﻨﺸﺎﻓﺔ ﺑﺎﻟﻤﺎء ﻏﻴﺮ آﺎﻓﻲ اﺳﺘﻌﻴﻨﻮا ﺑﻘﺴﻢ اﻟﺼﻴﺎﻧﺔ

اﻟﻔﻨﻴﺔ أو اﻟﻤﺤﻼ ت اﻟﻤﺨﺘﺼﺔ أو ﻓﻨﻲ ﻣﺆهﻞ ﺑﺎﻟﻘﻴﺎم ﺑﻌﻤﻠﻴﺎت اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ.

ﻲﺑﺮﻋ

اوﺻﻠﻮا ﺧﺮﻃﻮم ﺗﻔﺮﻳﻎ اﻟﻤﺎء ﻣﻦ ﺣﻮض

ﻏ

ﺴ

ﻴ

ﻞ اﻟ

ﻐ

ﺴ

ﺎﻟ

ﺔ ﺑ

ﺪون ﻃ

ﻮﻳ

ﻪ، ﺑ

ﻤ

ﺎﺳ

ﻮرة

ﺻ

ﺮف ﻟ

ﻠ

ﻤ

ﺎء، أو ﺑ

ﻤ

ﺼ

ﺮف ﻣ

ﻮﺟ

ﻮد ﻓ

ﻲ

اﻟﺤﺎﺋﻂ ﻋﻠﻰ أن ﻳﻜﻮن ارﺗﻔﺎﻋﻪ ﻣﺎ ﺑﻴﻦ 56

و 001 ﺳﻨﺘﻤﺘﺮ ﻋﻦ ﺳﻄﺢ اﻷ رض

أو ﻗ

ﻮﻣ

ﻮا ﺑ

ﻮﺿ

ﻌ

ﻪ ﻋ

ﻠ

ﻰ ﺣ

ﺎﻓ

ﺔ ﻣ

ﻐ

ﺴ

ﻠ

ﺔ

أو ﺣ

ﻮض ﺣ

ﻤ

ﺎم، ارﺑ

ﻄ

ﻮا اﻟ

ﺨ

ﺮﻃ

ﻮم

ﺑ

ﺤ

ﺎﻣ

ﻞ اﻟ

ﺨ

ﺮﻃ

ﻮم اﻟ

ﺬي ﻳ

ﻜ

ﻮن ﻣ

ﺰود ﻣ

ﻊ

اﻟﺠﻬﺎزﺑﻤﺤﺒﺲ اﻟﻤﺎء )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

اﻟﻄﺮف اﻟﺤﺮ ﻣﻦ اﻟﺨﺮﻃﻮم ﻳﺠﺐ أن ﻻ

ﻳﻜﻮن ﻣﻐﻤﻮر ﻓﻲ اﻟﻤﺎء.

ﻏﻴﺮ ﻣﻨﺼﻮح اﺳﺘﺨﺪام ﺧﺮاﻃﻴﻢ ﺗﻄﻮﻳﻞ ، اذا آﺎن ﻣﻦ اﻟﻀﺮوري اﺳﺘﺨﺪام ﺧﺮاﻃﻴﻢ

اﻟ

ﺘ

ﻄ

ﻮﻳ

ﻞ ﻳ

ﺠ

ﺐ أن ﻳ

ﻜ

ﻮن ﻗ

ﻄ

ﺮ ه

ﺬا اﻟ

ﺨ

ﺮﻃ

ﻮم ﻧ

ﻔ

ﺲ ﻗ

ﻄ

ﺮ اﻟ

ﺨ

ﺮﻃ

ﻮم اﻟ

ﺮﺋ

ﻴ

ﺴ

ﻲ وﻳ

ﺠ

ﺐ

أن ﻻ ﻳﺰﻳﺪ ﻃﻮﻟﻪ ﻋﻦ 051 ﺳﻨﺘﻤﺘﺮ.

اﻟﺘﻮﺻﻴﻞ ﺑﺸﺒﻜﺔ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ

ﻗﺒﻞ ادﺧﺎل ﻗﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( ﺑﻤﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﺗﺄآﺪوا

ﻣﻦ أن:

ﻣﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﻟﻬﺎ ﺧﻂ أرض ﻓﻌﺎل وﺧﺎﺿﻊ اﻟﻰ اﻟﻘﻮاﻧﻴﻦ

ﻣ

ﻘ

ﺒ

ﺲ اﻟ

ﺘ

ﻴ

ﺎر اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ )اﻷ ﻧ

ﺜ

ﻰ( ﻗ

ﺎدر ﻋ

ﻠ

ﻰ ﺗ

ﺤ

ﻤ

ﻞ اﻟ

ﻘ

ﺪرة اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ اﻟ

ﻘ

ﺼ

ﻮى

اﻟ

ﻤ

ﺘ

ﺼ

ﺔ ﻣ

ﻦ ﻗ

ﺒ

ﻞ اﻟ

ﺠ

ﻬ

ﺎزوﻳ

ﻜ

ﻮن ﻣ

ﺸ

ﺎر ﻟ

ﻬ

ﺎ ﻓ

ﻲ ﻻ ﺋ

ﺤ

ﺔ اﻟ

ﺨ

ﺼ

ﺎﺋ

ﺺ اﻟ

ﻔ

ﻨ

ﻴ

ﺔ ﻟ

ﻠ

ﺠ

ﻬ

ﺎز

)اﻧﻈﺮﺻﻔﺤﺔ 91(.

ﻓﺮق ﺟﻬﺪ ﺷﺒﻜﺔ اﻟﻜﻬﺮﺑﺎء ﻳﺠﺐ أن ﺗﻜﻮن ﻓﻲ اﻟﻘﻴﻢ اﻟﺘﻲ ﺗﻜﻮن ﻣﻮﺟﻮدة واﻟﻤﺸﺎر ﻟﻬﺎ

ﻓﻲ ﻻ ﺋﺤﺔ اﻟﺨﺼﺎﺋﺺ اﻟﻔﻨﻴﺔ ﻟﻠﺠﻬﺎز)اﻧﻈﺮﺻﻔﺤﺔ 91(.

ﻣﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﻣﻼ ﺋﻢ ﻟﻘﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( اﻟﻤﺰود ﻣﻊ

اﻟﻐﺴﺎﻟﺔ ﻓﻲ ﺣﺎﻟﺔ ﻋﺪم ﺗﻮاﻓﻘﻬﻢ ﻗﻮﻣﻮا ﺑﻌﻤﻠﻴﺔ ﺗﻐﻴﻴﺮ اﺣﺪاهﻤﺎ.

ﺟ

ﻬ

ﺎزآ

ﻢ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﻣ

ﺰود ﺑ

ﻘ

ﺎﺑ

ﺲ )اﻟ

ﺬآ

ﺮ( ﻣ

ﺼ

ﻬ

ﻮر وﻗ

ﺎدرﻋ

ﻠ

ﻰ ﺗ

ﺤ

ﻤ

ﻞ ﺗ

ﻴ

ﺎر آ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ

31 أﻣﺒﻴﺮ وﻳﻤﻜﻨﻜﻢ ادﺧﺎل هﺬا اﻟﻘﺎﺑﺲ ﺑﻤﻘﺒﺲ )اﻻ ﻧﺜﻰ( ﻳﺘﻮاﻓﻖ ﻣﻌﺔ ﻟﻼ ﺳﺘﺨﺪام اﻟﻤﺒﺎﺷﺮ،

اﻗﺮؤوا اﻟﺘﻌﻠﻴﻤﺎت اﻟﺘﺎﻟﻴﺔ ﻗﺒﻞ اﺳﺘﺨﺪام اﻟﺠﻬﺎز اﻟﻜﻬﺮﺑﺎﺋﻲ.

اﻧ

ﺘ

ﺒ

ﺎه: اﻟ

ﺠ

ﻬ

ﺎز اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﻳ

ﺠ

ﺐ أن ﻳ

ﻜ

ﻮن ﻣ

ﻮﺻ

ﻮل ﺑ

ﺨ

ﻂ أرض ﻓ

ﻌ

ﺎل، اﻟ

ﻌ

ﻤ

ﻠ

ﻴ

ﺎت

اﻟﻤﺸﺮوﺣﺔ أدﻧﺎه هﻲ ﺗﻌﻠﻴﻤﺎت ﻣﻮﺟﻪ اﻟﻰ ﻓﻨﻲ آﻬﺮﺑﺎﺋﻲ ﻣﺨﺘﺺ.

65 - 100 cm

ﺗﻐﻴﻴﺮ اﻟﻤﻨﺼﻬﺮة )اﻟﻔﻴﻮز(

ﻋ

ﻨ

ﺪ ﺗ

ﻐ

ﻴ

ﺮ اﻟ

ﻤ

ﻨ

ﺼ

ﻬ

ﺮة )اﻟ

ﻔ

ﻴ

ﻮز( اﻟ

ﻤ

ﻌ

ﻄ

ﻮب، اﺳ

ﺘ

ﺨ

ﺪﻣ

ﻮا داﺋ

ﻤ

ﺎ ﻣ

ﻨ

ﺼ

ﻬ

ﺮة 31 اﻣ

ﺒ

ﻴ

ﺮ

ATSA ﺧﺎﺿﻌﺔ ﻟﻠﻤﻘﻴﺎس 2631 SB وأﻋﻴﺪوا ﻏﻄﺎء اﻟﻤﻨﺼﻬﺮة اﻟﻰ ﻣﻜﺎﻧﻪ اﻟﺬي

ﺎن ﻓ

ﻴ

ﻪ، ﻓ

ﻲ ﺣ

ﺎﻟ

ﺔ ﻓ

ﻘ

ﺪان ه

ﺬا اﻟ

ﻐ

ﻄ

ﺎء ﻻ ﺗ

ﺴ

ﺘ

ﺨ

ﺪﻣ

ﻮا اﻟ

ﻘ

ﺎﺑ

ﺲ ﺣ

ﺘ

ﻰ اﻟ

ﺤ

ﺼ

ﻮل ﻋ

ﻠ

ﻰ

هﺬا اﻟﻐﻄﺎء وﺗﺮآﻴﺒﻪ ﻓﻲ ﻣﻜﺎﻧﻪ.

ﺗﻐﻴﻴﺮ ﻏﻄﺎء اﻟﻤﻨﺼﻬﺮات )اﻟﻔﻴﻮزات(:

اذا ﺗﻢ ﺗﻐﻴﻴﺮ ﻏﻄﺎء اﻟﻔﻴﻮزات ﺗﺎآﺪوا ﻣﻦ أن ﻟﻮﻧﻪ هﻮ اﻟﻠﻮن اﻟﺼﺤﻴﺢ واﻟﻤﺸﺎر ﻟﻪ

ﺑﻮاﺳﻄﺔ اﻟﺮﻗﻢ أو اﻟﻜﺘﺎﺑﺔ اﻟﻤﻠﻮﻧﺔ اﻟﻤﻮﺟﻮدة ﻋﻠﻰ ﻗﺎﻋﺪة اﻟﻘﺎﺑﺲ، ﻟﻘﻄﻊ اﻟﻐﻴﺎر، اﺳﺘﻌﻴﻨﻮا

ﻣﺒﺎﺷﺮة ﺑﻘﺴﻢ اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ اﻟﻘﺮﻳﺐ ﻋﻠﻴﻜﻢ.

ﻓﻚ اﻟﻘﺎﺑﺲ )اﻟﺬآﺮ(:

ﻓﻲ ﺣﺎﻟﺔ أن ﻳﻜﻮن اﻟﺠﻬﺎز ﻣﺰود ﺑﻘﺎﺑﺲ )اﻟﺬآﺮ( ﻻ ﻳﻤﻜﻦ ﻓﻜﻪ ﻷ ﻧﻪ ﻣﺼﻬﻮر وﺗﺮﻳﺪون

ﺗﻤﺮﻳﺮ ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻣﻦ ﺧﻼ ل ﺛﻘﻮب أو ﻓﺘﺤﺎت ﺻﻐﻴﺮة ﻻ ﻳﻤﺮ ﻣﻦ ﺧﻼ ﻟﻬﺎ

اﻟﻘﺎﺑﺲ ﻗﻮﻣﻮا ﺑﺘﻐﻴﻴﺮ اﻟﻘﺎﺑﺲ اﻟﻤﺼﻬﻮر ﺑﻘﺎﺑﺲ ﻳﻤﻜﻦ ﻓﻜﻪ وﺗﺮآﻴﺒﻪ وﻗﺎدر ﻋﻠﻰ ﺗﺤﻤﻞ

31 أﻣﺒﻴﺮ وﻳﺤﻤﻞ اﻟﺸﻌﺎر ISB.

أو

وﺻ

ﻞ ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﺑ

ﻤ

ﻨ

ﺒ

ﻊ اﻟ

ﺘ

ﻴ

ﺎر اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﺑ

ﻮاﺳ

ﻄ

ﺔ ﻣ

ﻔ

ﺘ

ﺎح ﻗ

ﺎدر ﻋ

ﻠ

ﻰ

ﺗ

ﺤ

ﻤ

ﻞ 31 أﻣ

ﺒ

ﻴ

ﺮ )وﺧ

ﺎﺿ

ﻊ ﻟ

ﻠ

ﻤ

ﻘ

ﻴ

ﺎس 3375 SB ( ﻳ

ﻤ

ﻜ

ﻦ اﻟ

ﻮﺻ

ﻮل اﻟ

ﻴ

ﻪ ﺑ

ﺪون

ﺗﺤﺮﻳﻚ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎﻧﻪ.

ازاﻟﺔ اﻟﻘﺎﺑﺲ )اﻟﺬآﺮ(:

ﻗﺒﻞ رﻣﻲ اﻟﻘﺎﺑﺲ اﺟﻌﻠﻮة ﻏﻴﺮ ﻗﺎﺑﻞ ﻟﻼ ﺳﺘﻌﻤﺎل وذﻟﻚ ﺑﻜﺴﺮ رؤوﺳﻪ ﺑﺤﻴﺚ ﻻ ﻳﻤﻜﻦ

ادﺧﺎﻟﻪ داﺧﻞ ﺛﻘﻮب ﻣﻘﺒﺲ )اﻻ ﻧﺜﻰ( ﺑﺸﻜﻞ ﻋﻔﻮي.

ﺗﻌﻠﻴﻤﺎت ﻣﻦ أﺟﻞ ﺗﻮﺻﻴﻞ ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺑﻘﺎﺑﺲ )اﻟﺬآﺮ(:

ﻣﻬﻢ: أﻟﻮان اﻷ ﺳﻼ ك اﻟﺘﻐﺬﻳﻪ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺗﺸﻴﺮ اﻟﻰ اﻟﺘﺎﻟﻲ:

أﺻﻔﺮ/أﺧﻀﺮ ﺧﻂ أرض

ازرق ﻣﺤﺎﻳﺪ )ﻧﻴﻮﺗﺮل(

ﺑﻨﻲ ﺗﻐﺬﻳﺔ

وﻷ ن أﻟ

ﻮان ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﻳ

ﻤ

ﻜ

ﻦ أن ﻻ ﻳ

ﻄ

ﺎﺑ

ﻘ

ﻮا اﻻ ﺷ

ﺎرات اﻟ

ﻤ

ﻠ

ﻮﻧ

ﺔ اﻟ

ﺘ

ﻲ

ﺗﻌﺮف ﻣﺮاﺑﻂ اﻟﻘﺎﺑﺲ، اﺗﺒﻌﻮا اﻟﺨﻄﻮات اﻟﺘﺎﻟﻴﺔ:

أوﺻﻠﻮا اﻟﺴﻠﻚ اﻷ ﺻﻔﺮ/اﻷ ﺧﻀﺮ ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف E أو ﺑﺎﻟﺸﻌﺎر أو

اﻟﻠﻮن اﻷ ﺧﻀﺮ أو اﻷ ﺻﻔﺮ/اﻷ ﺧﻀﺮ

أوﺻﻠﻮا اﻟﺴﻠﻚ اﻟﺒﻨﻲ ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف L أو ﺑﺎﻟﻠﻮن اﻷ ﺣﻤﺮ.

أوﺻﻠﻮا اﻟﺴﻠﻚ اﻷ زرق ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف N أو ﺑﺎﻟﻠﻮن اﻷ ﺳﻮد.

اذا اﺳﺘﺨﺪﻣﺘﻢ ﻗﺎﺑﺲ )اﻟﺬآﺮ( 31 أﻣﺒﻴﺮ )3631 SB( رآﺒﻮا ﻣﻨﺼﻬﺮة )ﻓﻴﻮز( 31

أﻣﺒﻴﺮ ﻓﻲ اﻟﻤﻘﺒﺲ أو ﻓﻲ اﻟﻤﻬﺎي

أو ﻋﻠﻰ ﻟﻮﺣﺔ اﻟﺘﻮزﻳﻊ.

ﻲﺑﺮﻋ

ﻓ

ﻲ ﺣ

ﺎﻟ

ﺔ اﻟ

ﺸ

ﻚ ﺑ

ﺎﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﻟ

ﺠ

ﻬ

ﺎزآ

ﻢ اﺳ

ﺘ

ﺪﻋ

ﻮا ﻓ

ﻨ

ﻲ آ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﻣ

ﺨ

ﺘ

ﺺ ﻗ

ﺒ

ﻞ

وﺻﻞ اﻟﺠﻬﺎز ﺑﻤﻨﺒﻊ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ.

وﺻﻞ ﻗﺎﺑﺲ )اﻟﺬآﺮ( ﺑﺪﻳﻞ:

أﻟﻮان اﻷ ﺳﻼ ك اﻟﺘﻐﺬﻳﻪ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺗﺸﻴﺮ اﻟﻰ اﻟﺘﺎﻟﻲ:

ازرق ﻣﺤﺎﻳﺪ )ﻧﻴﻮﺗﺮل( )N(

ﺑﻨﻲ ﺗﻐﺬﻳﺔ )L(

أﺻﻔﺮ/أﺧﻀﺮ ﺧﻂ أرض )E(

ازاﻟﺔ اﻟﺠﻬﺎز اﻟﻜﻬﺮﺑﺎﺋﻲ اﻟﺒﻴﺘﻲ:

ﻋﻨﺪ رﻣﻲ ﺟﻬﺎز آﻬﺮﺑﺎﺋﻲ ﺑﻴﺘﻲ، ﻳﺠﺐ ازاﻟﺔ ﻗﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( وذﻟﻚ

ﺑ

ﻘ

ﺺ ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﺑ

ﺄﻗ

ﺮب ﻧ

ﻘ

ﻄ

ﺔ ﻣ

ﻤ

ﻜ

ﻨ

ﺔ ﻣ

ﻦ اﻟ

ﻘ

ﺎﺑ

ﺲ وﻗ

ﻮﻣ

ﻮا ﺑ

ﺘ

ﺤ

ﻄ

ﻴ

ﻢ

رؤوس اﻟﻘﺎﺑﺲ آﻤﺎ ذآﺮ ﺳﺎﺑﻘﺎ.

VERDE &

GIALLO

MARRONE

BLU

fusibile

13 ampere

SERRAFILO

CROSSBAR

ﻣ

ﻨ

ﺼ

ﻬ

ﺮة 31

أﻣﺒﻴﺮ

ﻣﺮﺑﻂ ﺳﻠﻚ

أﺧﻀﺮ

أﺻﻔﺮ

ﺑﻨﻲ

أزرق

!اﻟﻐﺴﺎﻟﺔ ﻻ ﺗﻮﺿﻊ ﻓﻲ اﻟﺨﺎرج ﺣﺘﻰ ﻟﻮ آﺎن اﻟﻤﻜﺎن ﻣﻐﻄﻰ وذﻟﻚ ﻷ ﻧﻪ ﻣﻦ اﻟﺨﻄﺮ ﺗﺮك

اﻟﺠﻬﺎز ﺗﺤﺖ ﻋﻮاﻣﻞ اﻟﻄﻘﺺ ﻣﺜﻞ اﻟﻤﻄﺮ ﺑﺮق رﻋﺪ اﻟﻰ اﺧﺮه.

! ﺑ

ﻌ

ﺪ اﻻ ﻧ

ﻬ

ﺎء ﻣ

ﻦ ﺗ

ﺮآ

ﻴ

ﺐ اﻟ

ﺠ

ﻬ

ﺎز ﻳ

ﺠ

ﺐ أن ﻳ

ﻜ

ﻮن ﻣ

ﻦ اﻟ

ﺴ

ﻬ

ﻞ اﻟ

ﻮﺻ

ﻮل اﻟ

ﻰ ﻣ

ﻘ

ﺒ

ﺲ

اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ(.

! ﻻ ﺗﺴﺘﺨﺪﻣﻮا ﻣﻬﺎﻳﺌﺎت او ﻣﻘﺒﺲ ﻣﺘﻌﺪد اﻟﺜﻘﻮب أو اﺳﻼ ك ﺗﻄﻮﻳﻞ.

! ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻳﺠﺐ أن ﻻ ﻳﻜﻮن ﻣﻄﻮي أو ﻣﺤﺸﻮر ﺑﻴﻦ اﻷ ﺛﺎث.

!ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﻳ

ﺠ

ﺐ أن ﻳ

ﺘ

ﻢ ﺗ

ﺒ

ﺪﻳ

ﻠ

ﻪ وﻗ

ﺖ اﻟ

ﺤ

ﺎﺟ

ﺔ ﻓ

ﻘ

ﻂ ﻣ

ﻦ ﻗ

ﺒ

ﻞ ﻓ

ﻨ

ﻲ ﻣ

ﺨ

ﺘ

ﺺ

وﻣﺆهﻞ ﻟﻠﻘﻴﺎم ﺑﻬﺬا.

اﻧﺘﺒﺎه: اﻟﺸﺮآﺔ اﻟﺼﺎﻧﻌﺔ ﺗﺴﻘﻂ ﻋﻦ ﻧﻔﺴﻬﺎ أي ﻣﺴﺆوﻟﻴﺔ ﻋﻦ أﺿﺮار ﻗﺪ ﺗﺤﺼﻞ ﻣﻦ

ﻋﺪم اﺗﺒﺎع واﺣﺘﺮام هﺬه ﻗﻮاﻋﺪ اﻷ ﻣﻦ.

أول دورة ﻏﺴﻴﻞ

ﺑﻌﺪ اﻻ ﻧﺘﻬﺎء ﻣﻦ ﻋﻤﻠﻴﺔ ﺗﺮآﻴﺐ اﻟﺠﻬﺎز، وﻗﺒﻞ اﺳﺘﺨﺪاﻣﻪ، ﻗﻮﻣﻮا ﺑﻌﻤﻠﻴﺔ ﻏﺴﻴﻞ ﻣﺴﺘﺨﺪﻣﻴﻦ

ﻣﺴﺤﻮق ﻏﺴﻴﻞ وﺑﺪون ﻣﻼ ﺑﺲ داﺧﻞ اﻟﻐﺴﺎﻟﺔ، ﻣﺴﺘﺨﺪﻣﻴﻦ ﺑﺮﻧﺎﻣﺞ اﻟﻐﺴﻴﻞ ﻋﻠﻰ 09

درﺟﺔ ﻣﺌﻮﻳﺔ ﺑﺪون ﻋﻤﻠﻴﺔ ﻏﺴﻴﻞ ﺑﺪاﺋﻴﺔ.

ﻣﻮاﺻﻔﺎت ﻓﻨﻴﺔ

اﻟﻤﺪﻳﻞ

IDXL 126W

اﻷ ﺑﻌﺎد

اﻟﻌﺮض 5.95 ﺳﻨﺘﻤﺘﺮ

اﻻ رﺗﻔﺎع 58 ﺳﻨﺘﻤﺘﺮ

اﻟﻌﻤﻖ 5.35 ﺳﻨﺘﻤﺘﺮ

اﻟﻘﺪرة

ﻣﻦ 1 اﻟﻰ 6 آﻐﻢ ﻓﻲ ﻋﻤﻠﻴﺔ اﻟﻐﺴﻴﻞ

ﻣﻦ 1 اﻟﻰ4 آﻐﻢ ﻓﻲ ﻋﻤﻠﻴﺔ اﻟﺘﻨﺸﻴﻒ

اﻟﺘﻮﺻﻴﻼ ت اﻟﻜﻬﺮﺑﺎﺋﻴﺔ

ﻓﺮق ﺟﻬﺪ 032/042 ﻓﻮﻟﺖ 05 هﻴﺮﺗﺰ

اﻟﻘﺪرة اﻟﻘﺼﻮى اﻟﻤﻤﺘﺼﺔ ﻣﻦ ﻗﺒﻞ اﻟﺠﻬﺎز 0502 واط

اﻟﺘﻮﺻﻴﻼ ت اﻟﻬﻴﺪروﻟﻴﻜﻴﺔ

اﻟﻀﻐﻂ اﻟﻘﺼﻮى 1 ﻣﻠﺒﺴﻜﺎل )01 ﺑﺎر(

اﻟﻀﻐﻂ اﻟﺪﻧﻴﺎ 50.0 ﻣﻴﻠﻴﺒﺴﻜﺎل )5.0 ﺑﺎر(

ﻗﺪرة ﺣﻮض اﻟﻐﺴﻴﻞ 25 ﻟﺘﺮ

ﺳﺮﻋﺔ اﻟﻌﺼﺮ اﻟﺪوراﻧﻴﺔ

ﺑﺮاﻣﺞ ﺗﺠﺮﺑﺔ اﻟﺠﻬﺎز ﺣﺴﺐ

اﻟﻘﻮاﻋﺪ

اﻟﻐﺴﻴﻞ: ﺑﺮﻧﺎﻣﺞ 2، درﺟﺔ ﺣﺮارة 06 درﺟﺔ ﻣﺌﻮﻳﺔ، ﺗﻤﺖ

اﻟﺘﺠﺮﺑﺔ ﺑﺤﻤﻞ ﻏﺴﻴﻞ 6 آﻐﻢ

اﻟ

ﺘ

ﻨ

ﺸ

ﻴ

ﻒ: اﻟ

ﺘ

ﺸ

ﻴ

ﻒ اﻷ ول ﺗ

ﻢ ﺑ

ﺤ

ﻤ

ﻞ 2 آ

ﻐ

ﻢ وﺑ

ﺎﺧ

ﺘ

ﻴ

ﺎر زﻣ

ﻦ

ﺗﻨﺸﻴﻒ دﻗﻴﻘﺔ، اﻟﺘﻨﺸﻴﻒ اﻟﺜﺎﻧﻲ ﺗﻢ ﺑﺤﻤﻞ4 آﻐﻢ وﺑﻮﺿﻊ

ﻣﻘﺒﺾ اﻟﺘﻨﺸﻴﻒ ﻋﻠﻰ اﻟﻮﺿﻊ

هﺬا اﻟﺠﻬﺎز ﻳﻄﺎﺑﻖ اﻟﻤﻮاﺻﻔﺎت اﻟﻤﻄﻠﻮﺑﺔ ﻣﻦ ﺳﻮق اﻟﺪول

اﻷ ورﺑﻴﺔ اﻟﻤﺸﺘﺮآﺔ:

- ﺑﻤﺎ ﻳﺘﻌﻠﻖ ﺑﻔﺮق ﺟﻬﺪ ﻣﻨﺨﻔﺾ

- ﺑﻤﺎ ﻳﺘﻌﻠﻖ اﻟﺘﻮاﻓﻖ اﻟﻜﻬﺮوﻣﻐﻨﺎﻃﻴﺴﻲ

ﺣﺘﻰ 0021 دورة ﻓﻲ اﻟﺪﻗﻴﻘﺔ

EN 50229

ﻲﺑﺮﻋ

ﺲﺑ ﻼﻤﻟا ﺔﻓﺎﺸﻧ ﺔﻟﺎﺴﻏ ﻒﺻو

ﻟ

ﻮﺣ

ﺔ اﻟ

ﻘ

ﻴ

ﺎدة

ﻣﻘﺒﺾ

اﻟﺒﺮاﻣﺠﺔ

زر

ﺑﺪء/ﺷﻄﺐ اﻟﺒﺮﻧﺎﻣﺞ

زر

ﺗﺸﻐﻴﻞ/ اﻃﻔﺎء

زر

وﻇﺎﺋﻒ

ﻣﻘﺒﺾ

اﻟﺘﻨﺸﻴﻒ

ﻣﻘﺒﺾ

درﺟﺔ اﻟﺤﺮارة

ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ

ﺣ

ﻮض ﻣ

ﺴ

ﺎﺣ

ﻴ

ﻖ اﻟ

ﻐ

ﺴ

ﻴ

ﻞ ﻟ

ﻮﺿ

ﻊ ﻣ

ﺴ

ﺎﺣ

ﻴ

ﻖ اﻟ

ﻐ

ﺴ

ﻴ

ﻞ واﻟ

ﻤ

ﺴ

ﺎﺣ

ﻴ

ﻖ اﻻ ﺿ

ﺎﻓ

ﻴ

ﺔ )اﻧ

ﻈ

ﺮ

ﺻﻔﺤﺔ رﻗﻢ 42(

ﻣﺼﺎﺑﻴﺢ اﻻ ﻧﺬار ﻟﻤﺮاﻗﺒﺔ ﺣﺎﻟﺔ ﺗﻘﺪم ﺑﺮﻧﺎﻣﺞ اﻟﻐﺴﻴﻞ ﺧﻼ ل ﻋﻤﻠﻪ

اذا ﺗﻢ وﺿﻊ اﻟﻮﻇﻴﻔﺔ ﺗﺄﺧﻴﺮ ﻋﻤﻞ دورة اﻟﻐﺴﻴﻞ remiT yaleD ﺳﻮف ﻳﺸﻴﺮون اﻟﻰ

اﻟﺰﻣﻦ اﻟﻤﺘﺒﻘﻲ ﺣﺘﻰ ﺗﺒﺪأ دورة اﻟﻐﺴﻴﻞ )اﻧﻈﺮ اﻟﻰ ﺻﻔﺤﺔ 12(

ﻣ

ﻘ

ﺒ

ﺾ اﻟ

ﺘ

ﻨ

ﺸ

ﻴ

ﻒ ﻟ

ﻮﺿ

ﻊ وﺑ

ﺮﻣ

ﺠ

ﺔ ﻋ

ﻤ

ﻠ

ﻴ

ﺔ اﻟ

ﺘ

ﻨ

ﺸ

ﻴ

ﻒ اﻟ

ﺘ

ﻲ ﺗ

ﺮﻏ

ﺒ

ﻮن اﺳ

ﺘ

ﺨ

ﺪاﻣ

ﻬ

ﺎ )اﻧ

ﻈ

ﺮ

ﺻﻔﺤﺔ 32(

أزرار اﻟﻮﻇﺎﺋﻒ ﻻ ﺧﺘﻴﺎر اﻟﻮﻇﺎﺋﻒ اﻟﺘﻲ ﺗﻜﻮن ﻣﺰودة ﺑﻬﺎ ﻏﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ اﻟﻤﻼ ﺑﺲ، اﻟﺰر

اﻟﺬي ﻳﻘﻮم ﺑﺘﺸﻐﻴﻞ اﺣﺪي اﻟﻮﻇﺎﺋﻒ ﻳﻜﻮن ﻣﻀﻲء ﻋﻨﺪ اﺧﺘﻴﺎره.

ﻣﻘﺒﺾ درﺟﺔ اﻟﺤﺮارة ﻟﻮﺿﻊ درﺟﺔ ﺣﺮارة اﻟﻐﺴﻴﻞ أو اﻟﻘﻴﺎم ﺑﻌﻤﻠﻴﺔ اﻟﻐﺴﻴﻞ ﺑﻤﺎء

ﺑﺎرد )اﻧﻈﺮ اﻟﻰ ﺻﻔﺤﺔ 32(

زر ﺑﺪء/ﺷﻄﺐ اﻟﺒﺮﻧﺎﻣﺞ TESER/TRATS ﻟﺘﺸﻐﻴﻞ اﻟﺒﺮاﻣﺞ أو اﻟﻐﺎﺋﻬﺎ ﻋﻨﺪﻣﺎ

ﻳﻘﻊ ﺧﻄﺄ ﻓﻲ اﻟﺒﺮﻣﺠﺔ

ﻣﺼﺒﺎح اﻧﺬاراﺷﺘﻐﺎل/ﺑﺎب اﻟﻐﺴﺎﻟﺔ اﻟﻨﺸﺎﻓﺔ ﻣﻘﻔﻞ ﻟﻔﻬﻢ اذا ﻣﺎ آﺎﻧﺖ ﻏﺴﺎﻟﺔ ﻧﺸﺎﻓﺔ اﻟﻤﻼ ﺑﺲ

ﺗﺸﺘﻐﻞ واذا آﺎن ﻣﻦ اﻟﻤﻤﻜﻦ ﻓﺘﺢ ﺑﺎب اﻟﻐﺴﺎﻟﺔ اﻟﻨﺸﺎﻓﺔ )اﻧﻈﺮ اﻟﻰ ﺻﻔﺤﺔ 12(

زر ﺗﺸﻐﻴﻞ/اﻃﻔﺎء ﻟﺘﺸﻐﻴﻞ واﻃﻔﺎء اﻟﻐﺴﺎﻟﺔ اﻟﻨﺸﺎﻓﺔ.

ﻣﻘﺒﺾ اﻟﺒﺮﻣﺠﺔ ﻟﻮﺿﻊ اﻟﺒﺮاﻣﺞ )اﻧﻈﺮ اﻟﻰ ﺻﻔﺤﺔ 22(،

ﺧﻼ ل اﻟﺒﺮﻧﺎﻣﺞ ﻳﺒﻘﻰ اﻟﻤﻘﺒﺾ ﺛﺎﺑﺖ ﻓﻲ ﻣﻜﺎﻧﻪ.

ﻣﺼﺎﺑﻴﺢ اﻧﺬار

ﻣﺼﺒﺎح اﻧﺬار

اﺷ

ﺘ

ﻐ

ﺎل/ﺑ

ﺎب

اﻟﻐﺴﺎﻟﺔ ﻣﻘﻔﻞ

Page is loading ...

Whirlpool WIDXL 126 (UK) User manual

Brand: Whirlpool

Model: WIDXL 126 (UK)

Category: Washing machines

Type: User manual

This manual is also suitable for

WIDXL 126

Download PDF

report

Whirlpool WIDXL 126 (UK) User manual

This manual is also suitable for

Whirlpool WIDXL 126 (UK) User manual

Related papers

Other documents