Indesit WI 82 (EX) 60 Hz User guide

Brand: Indesit

Model: WI 82 (EX) 60 Hz

Category: Washing machines

Type: User guide

Contents

Installation, 2-3-4-5

Unpacking and levelling, 2

Electric and water connections, 2-3

The first wash cycle, 4

Technical details, 5

Washing machine description, 6-7

Control panel, 6

Leds, 7

Starting and Programmes, 8

Briefly: how to start a programme, 8

Programme table, 8

Personalisations, 9

Setting the temperature, 9

Functions, 9

Detergents and laundry, 10

Detergent dispenser, 10

Preparing your laundry, 10

Special items, 10

Precautions and advice, 11

General safety, 11

Disposal, 11

Saving energy and respecting the environment, 11

Care and maintenance, 12

Cutting off the water or electricity supply, 12

Cleaning your appliance, 12

Cleaning the detergent dispenser, 12

Caring for your appliance door and drum, 12

Cleaning the pump, 12

Checking the water inlet hose, 12

Troubleshooting, 13

Service, 14

Before calling for Assistance, 14

WASHING MACHINE

WI 82

Instructions for use

English,1

Français,29

FRAR

, 15

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the 3

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Use the plug provided to seal the three holes

where the plug was housed, situated on the lower

right-hand side on the rear of your appliance.

6. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth (see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the

hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

Installation

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

 the supply voltage is included within the values i

ndicated on the Technical details table

(see page 5);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng

the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

65 - 100 cm

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible

to the plug body and dispose of it as described

above.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Technical details

Model

WI 82

Dimensions

59.5 cm wide

85 cm high

52.5 cm deep

Capacity

from 1 to 5 kg

Electric

connections

voltage 220/230 Volts 60 Hz

maximum absorbed power 1750 W

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 40 litres

Spin speed

up to 800 rpm

Control

programmes

according to

IEC456 directive

programme 3; temperature 60°C;

run with a load of 5 kg.

This appliance is compliant with the

following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

Washing machine description

Control panel

Detergent dispenser

ON-OFF

Button

TEMPERATURE

Knob

PROGRAMME

Knob

FUNCTION

Buttons

DOOR

LOCK

Led

Detergent dispenser: to add detergent and fabric

softener (see page 10).

FUNCTION buttons: to select the functions

available.

TEMPERATURE knob: to set the temperature or

the cold wash cycle (see page 9).

DOOR LOCK led, to find out if the appliance door

can be opened (see page 7).

ON/OFF button, to turn the washing machine on

and off.

Turning the machine off does not cancel the

selected programme.

ON/OFF led, to find out whether the washing

machine is on and if the programme set has been

accepted (see page 7).

PROGRAMME knob: to select the wash

programmes.

Note: After the wash cycle has been set and

accepted by the washing machine, any changes to

the position of the knob will be of no use (except in

the

Stop/Reset position).

Turn this knob clockwise only.

ON-OFF

Led

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Leds

The LEDS provide important information.

This is what they can tell you:

DOOR LOCK Led

The safety led indicates that the washing machine

door is locked to prevent it from being opened

accidentally. To avoid any damages to lock

mechanism, you must wait for the led to extinguish,

before attempting to open the door which takes

around three minutes.

ON-OFF Led

Led flashes when the appliance is switched on and

awaiting a programme to be set. A steady light

means the appliance has accepted the selected

programme.

Type of fabric and

degree of soil

Program-

mes

Te m p e -

rature

Detergent

Fabric

softener

Cycle

length

(minu tes)

Description of wash cycle

pre-

wash

Cotton

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C   

165

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C  

145

Wash cycle, rinse cycles, intermediate

and final spin cycles

Heavily soiled whites and fast

colours

60°C  

130

Wash cycle, rinse cycles, intermediate

and final spin cycles

Slightly soiled whites and delicate

colours (shirts, jumpers, etc.)

40°C  

Wash cycle, rinse cycles, intermediate

and final spin cycles

Rinse cycles 

Rinse cycles, intermediate and final spin

cycles

Spin cycle Draining and final spin cycle

Stop/Reset Interrupts/Cancels the selected programme

Synthetics

Heavily soiled fast colour synthetics

(baby linen, etc.)

60°C  

100

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Delicate colour synthetics (all types

of slightly soiled garments)

40°C  

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Rinse cycle 

Rinse cycles, anti-crease or delicate spin

cycle

Fabric softener 

Rinse cycles with automatic introduction of

softener, anti-crease or delicate spin cycle

Spin cycle Draining and delicate spin cycle

Stop/Reset Interrupts/Cancels the selected programme

Delicates

Hand wash

(Wool)

40°C  

Wash cycle, rinse cycles, anti-crease and

delicate spin cycle

Particularly delicate garments and

fabrics (curtains, silk, viscose, etc.)

30°C  

Wash cycle, rinse cycles, anti-crease or

draining

Rinse cycles  Rinse cycles, anti-crease or draining

Spin cycle Draining and delicate spin cycle

Drain Drain

Stop/Reset Interrupts/Cancels the selected programme

Starting and Programmes

Programme table

Notes

for the description of the Anti-crease function, please see page 9. The information contained in the table is purely

indicative.

Briefly: starting a programme

1. Set the desired programme.

2. Set the wash temperature (see page 9).

3. Load your laundry into the appliance and shut

the door.

4. Add the detergent and any fabric softener

(see page 10).

5. Turn the appliance on by pressing button

. The

ON/OFF led begins to flash, after 5 seconds, the

setting is accepted, the led stops flashing (staying

on) and the wash cycle begins.

6. To cancel the cycle set, select one of the symbols

(Stop/Reset) and wait 5 seconds: when the

cancellation has been accepted, the ON/OFF led

flashes, and you can turn the appliance off and

set a new cycle.

7. When the programme is completed, the DOOR

LOCK led will turn off to indicate that the

appliance door can be opened.

Turn the washing machine off by pressing button

Take out your laundry and leave the appliance

door ajar to allow the drum to dry thoroughly.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Personalisations

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).

The temperature can be lowered, or even set to a cold wash (

Functions

To enable the functions, press the button corresponding to the desired function, according to the table below.

Function Effect Comments

Rapid

Cuts the duration of

the wash cycle by

30%.

It cannot be used together with the programmes for wool and silk.

Extra Rinse

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large quantities

of detergent.

No Spin

The washing machine

will not carry out a

spin cycle, but rather

a drum spin at

medium speed to

assist water draining.

We recommend that you use it when washing garments which are difficult

to iron.

Anti-crease

This function (represented by the symbol

) interrupts the wash programme, keeping the washing soaking in

water before draining. It is only enabled in programmes for synthetic fabrics, silk and curtains. It is very useful,

because it prevents delicate and synthetic fabrics from creasing (for example, when you cannot take the washing

out at the end of the wash cycle but only a few hours later). The programme can be completed by turning knob

PROGRAMME one notch. In the case of synthetic fabrics, should you prefer draining rather than a spin cycle,

turn knob PROGRAMME until you have selected the symbol

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

 Do not use hand wash detergent because it may

form too much foam.

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 5 kg

Synthetic fabrics: max 2.5 kg

Delicate fabrics: max 2 kg

Wool: max 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme 8

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Trainers: remove any mud. They can be washed

together with jeans and other tough garments, but

not with whites.

Wool: for best results, use a specific detergent,

taking care not to exceed a load of 1 kg.

Detergents and laundry

Precautions and advice

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

 The washing machine was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

Disposal

 Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

 Disposing of an old washing machine:

before scrapping your appliance, cut the power

supply cable and remove the appliance door.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Ariston

technology, your washing machine only needs less

than half the amount of water to get the best

results: an objective reached to respect the

environment.

Saving on detergent, water,

energy and time

 To avoid wasting resources, the washing machine

should be used with a full load. A full load instead

of two half loads allows you to save up to 50% on

energy.

 The pre-wash cycle is only necessary on

extremely soiled garments. Avoiding it will save on

detergent, time, water and between 5 and 15%

energy.

 Treating stains with a stain remover or leaving

them to soak before washing will cut down the

need to wash them at high temperatures. A

programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on

energy.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

 If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump that does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber that protects the

pump, situated in the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

washing machine (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

Troubleshooting

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem

can't easily be solved by consulting the following list.

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water.

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

The programme selector knob

keeps turning?

There is too much foam.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to

make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 The

button has not been pressed.

 The water tap is not turned on.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The drain hose is not fitted between 65 and 100 cm from the floor

(see page 3).

 The free end of the hose is underwater (see page 3).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on

one of the upper floors of a building, there may be drain trap problems

causing the washing machine to load and unload water continuously.

In order to avoid such an inconvenience, special anti-drain trap valves

are available in shops.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 8).

 The Anti-crease function is enabled (where available): This function

requires enabling the draining manually.

 The drain hose is bent (see page 3).

 The drain duct is clogged.

 The drum was not unblocked correctly during installation (see page 2).

 The washing machine is not level (see page 2).

 The washing machine is closed in between furniture cabinets and

the wall (see page 2).

 The water inlet hose is not screwed on correctly (see page 2).

 The detergent dispenser is obstructed (to clean it, see page 12).

 The drain hose is not secured properly (see page 3).

 Wait a few minutes for the drain pump to empty the tub, switch the

washer off, select one of the symbols stop/reset

, then switch it

back on. If the knob continues to turn, call for assistance because i

t is showing an anomaly.

 The detergent is not suitable for machine washing (it should bear

the definition "for washing machines" or "hand and machine wash",

or the like).

 You used too much detergent.

Before calling for Assistance:

 Check whether you can solve the problem on your own (see page 13);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised servicemen.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Service

ﻲﺑﺮﻋ

لﺎﻤﻌﺘﺳ ﻻا ﻞﺟأ ﻦﻣ تﺎﻤﻴﻠﻌﺗ

ﺲﺑ ﻼﻣ ﺔﻟﺎﺴﻏ

WI 82

ﻲﺑﺮﻋ

اﻟﻔﻬﺮس

اﻟﺘﺮآﻴﺐ 61 - 71 - 81 - 91

اﺧﺮاج اﻟﺠﻬﺎز ﻣﻦ ﺗﻐﻠﻴﻔﻪ و ﺗﺴﻮﻳﺔ اﻟﺠﻬﺎز، 61

ﺗﻮﺻﻴﻼ ت اﻟﻤﺎء واﻟﻜﻬﺮﺑﺎء، 61 - 71

أول دورة ﻏﺴﻴﻞ، 81

ﻣﻮاﺻﻔﺎت ﻓﻨﻴﺔ، 91

وﺻﻒ ﻏﺴﺎﻟﺔ اﻟﻤﻼ ﺑﺲ 02 - 12

ﻟﻮﺣﺔ اﻟﻘﻴﺎدة، 02

ﻣﺼﺎﺑﻴﺢ اﻧﺬار، 12

اﻟﺘﺸﻐﻴﻞ و اﻟﺒﺮﻣﺠﺔ، 22

ﺑﺒﺴﺎﻃﺔ: ﺗﺸﻐﻴﻞ ﺑﺮﻧﺎﻣﺞ، 22

ﻟﻮﺣﺔ اﻟﺒﺮاﻣﺞ، 22

ﺗﺸﺨﻴﺺ، 32

وﺿﻊ درﺟﺔ اﻟﺤﺮارة؛ 32

وﻇﺎﺋﻒ، 32

ﻣﺴﺎﺣﻴﻖ ﻏﺴﻴﻞ و ﻣﻼ ﺑﺲ، 42

ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ، 42

ﺗﺤﻀﻴﺮ اﻟﻤﻼ ﺑﺲ ﻟﻠﻐﺴﻴﻞ، 42

أﻗﻤﺸﺔ ﺧﺎﺻﺔ، 42

ﺗﺤﺬﻳﺮات وﻧﺼﺎﺋﺢ، 52

أﻣﻦ ﻋﺎم، 52

اﻟﺘﺨﻠﺺ ﻣﻦ اﻟﻨﻔﺎﻳﺎت، 52

اﻻ ﻗﺘﺼﺎد و واﺣﺘﺮام اﻟﺒﻴﺌﺔ، 52

ﺻﻴﺎﻧﺔ و ﺣﻤﺎﻳﺔ، 62

اﻏﻼ ق اﻟﻤﺎء و اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ، 62

ﺗﻨﻈﻴﻒ ﻏﺴﺎﻟﺔ اﻟﻤﻼ ﺑﺲ، 62

ﺗﻨﻈﻴﻒ ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ، 62

ﺣﻤﺎﻳﺔ ﺑﺎب اﻟﻐﺴﺎﻟﺔ و ﺣﻮض ﻏﺴﻴﻞ اﻟﻐﺴﺎﻟﺔ، 62

ﺗﻨﻈﻴﻒ ﻣﻀﺨﺔ ﺗﻔﺮﻳﻎ اﻟﻐﺴﺎﻟﺔ ﻣﻦ اﻟﻤﺎء، 62

ﻓﺤﺺ ﺧﺮﻃﻮم ﺗﻐﺬﻳﺔ اﻟﻐﺴﺎﻟﺔ ﺑﺎﻟﻤﺎء، 62

ﺣﺼﻮل ﺑﻌﺾ اﻟﻤﺸﺎآﻞ وﺣﻠﻮل ﻟﻬﺎ، 72

اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ، 82

لﺎﻤﻌﺘﺳ ﻻا ﻞﺟأ ﻦﻣ تﺎﻤﻴﻠﻌﺗ

ﻣ

ﻦ اﻟ

ﻤ

ﻬ

ﻢ اﻟ

ﺤ

ﻔ

ﺎظ ﻋ

ﻠ

ﻰ ه

ﺬا اﻟ

ﻜ

ﺘ

ﻴ

ﺐ ﻟ

ﻴ

ﻤ

ﻜ

ﻨ

ﻜ

ﻢ اﻟ

ﻌ

ﻮدة اﻟ

ﻴ

ﻪ ﻋ

ﻨ

ﺪ اﻟ

ﺤ

ﺎﺟ

ﺔ اﻟ

ﻰ اﻟ

ﺘ

ﻌ

ﺮف

ﻋﻠﻰ ﻣﻌﻠﻮﻣﺎت ﻋﻦ اﻟﺠﻬﺎز ﻓﻲ أي ﻟﺤﻈﺔ، ﻓﻲ ﺣﺎﻟﺔ ﺑﻴﻊ اﻟﺠﻬﺎز أو اﻋﻄﺎءه آﻬﺪﻳﺔ أو

ﻋﻨﺪ ﻧﻘﻞ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎن ﻻ ﺧﺮ، ﺗﺄآﺪوا ﻣﻦ أن ﻳﺒﻘﻰ هﺬا اﻟﻜﺘﻴﺐ ﻣﻊ اﻟﺠﻬﺎز وذﻟﻚ

ﻟ

ﺘ

ﻘ

ﺪﻳ

ﻢ ﻣ

ﻌ

ﻠ

ﻮﻣ

ﺎت ﺗ

ﺘ

ﻌ

ﻠ

ﻖ ﺑ

ﺘ

ﺸ

ﻌ

ﻴ

ﻞ وﺑ

ﺮﻣ

ﺠ

ﺔ اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﺎﻻ ﺿ

ﺎﻓ

ﺔ اﻟ

ﻰ اﻟ

ﻨ

ﺼ

ﺎﺋ

ﺢ واﻟ

ﺘ

ﺤ

ﺬﻳ

ﺮ

ﻟﻠﻤﺎﻟﻚ اﻟﺠﺪﻳﺪ ﻟﻠﺠﻬﺎز.

أﻗ

ﺮؤوا ﺑ

ﺘ

ﻤ

ﻌ

ﻦ اﻟ

ﺘ

ﻌ

ﻠ

ﻴ

ﻤ

ﺎت: ﻓ

ﻲ داﺧ

ﻞ ه

ﺬا اﻟ

ﻜ

ﺘ

ﻴ

ﺐ ﻣ

ﻮﺟ

ﻮد ﻣ

ﻌ

ﻠ

ﻮﻣ

ﺎت ه

ﺎﻣ

ﺔ ﺗ

ﺘ

ﻌ

ﻠ

ﻖ

ﺑﺎﻟﺘﺮآﻴﺐ، اﻻ ﺳﺘﻌﻤﺎل، وأﻣﻦ اﻟﺠﻬﺎز.

اﺧﺮاج اﻟﺠﻬﺎز ﻣﻦ ﺗﻐﻠﻴﻔﻪ وﺗﺴﻮﻳﺔ اﻟﺠﻬﺎز

اﺧﺮاج اﻟﺠﻬﺎز ﻣﻦ ﺗﻐﻠﻴﻔﻪ

1. اﺧﺮﺟﻮا اﻟﻐﺴﺎﻟﺔ ﻣﻦ ﺗﻐﻠﻴﻔﻬﺎ

2. ﺗﺄآﺪوا ﻣﻦ اﻟﻐﺴﺎﻟﺔ ﻟﻢ ﻳﺤﺪث ﻟﻬﺎ أﺿﺮار ﺧﻼ ل ﺷﺤﻨﻬﺎ وﻧﻘﻠﻬﺎ ﻣﻦ ﻣﻜﺎن ﻻ ﺧﺮ،

اذا آ

ﺎن اﻟ

ﺠ

ﻬ

ﺎز ﻣ

ﻀ

ﺮر أو ﻣ

ﻀ

ﺮوب ﻓ

ﻲ ﻣ

ﻜ

ﺎن ﻣ

ﺎ ﻻ ﺗ

ﻘ

ﻮﻣ

ﻮا ﺑ

ﻌ

ﻤ

ﻠ

ﻴ

ﺔ ﺗ

ﻮﺻ

ﻴ

ﻠ

ﻪ أو

ﺗﺮآﻴﺒﻪ، واﺗﺼﻠﻮا ﺑﺎﻟﺒﺎﺋﻊ.

3. اﺧ

ﻠ

ﻌ

ﻮا اﻟ

ﺜ

ﻼ ث ﺑ

ﺮاﻏ

ﻲ اﻟ

ﺘ

ﻲ ﺗ

ﺤ

ﻤ

ﻲ

اﻟﺠﻬﺎز ﺧﻼ ل ﻋﻤﻠﻴﺔ اﻟﻨﻘﻞ، وآﺬﻟﻚ اﺧﻠﻌﻮا

اﻟ

ﻘ

ﻄ

ﻊ اﻟ

ﻤ

ﻄ

ﺎﻃ

ﻴ

ﺔ وﻣ

ﺒ

ﺎﻋ

ﺪ آ

ﻞ واﺣ

ﺪة ﻣ

ﻦ

ﺬه، اﻟ

ﺘ

ﻲ ﺗ

ﻜ

ﻮن ﻣ

ﻮﺟ

ﻮدة ﻓ

ﻲ اﻟ

ﻤ

ﻨ

ﻄ

ﻘ

ﺔ

اﻟﺨﻠﻔﻴﺔ ﻣﻦ اﻟﺠﻬﺎز )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

4. اﻏﻠﻘﻮا اﻟﺜﻘﻮب ﺑﻮاﺳﻄﺔ اﻷ ﻏﻄﻴﺔ اﻟﺒﻼ ﺳﺘﻴﻜﻴﺔ اﻟﺘﻲ ﺗﻜﻮن ﻣﺰودة ﻣﻊ اﻟﺠﻬﺎز.

5. أﻏ

ﻠ

ﻘ

ﻮا ﺑ

ﺎﻷ ﻏ

ﻄ

ﻴ

ﺔ اﻟ

ﺘ

ﻲ ﺗ

ﻜ

ﻮن ﻣ

ﺰودة ﻣ

ﻊ اﻟ

ﺠ

ﻬ

ﺎز اﻟ

ﺜ

ﻼ ث ﺛ

ﻘ

ﻮب ﺣ

ﻴ

ﺚ ﻳ

ﻜ

ﻮن

ﻣ

ﻮﺿ

ﻮع ﻗ

ﺎﺑ

ﺲ اﻟ

ﺘ

ﻴ

ﺎر اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ )اﻟ

ﺬآ

ﺮ( اﻟ

ﺬي ﻳ

ﻜ

ﻮن ﻣ

ﻮﺟ

ﻮد ﻓ

ﻲ ﺧ

ﻠ

ﻒ اﻟ

ﺠ

ﻬ

ﺎز

ﻣﻦ اﻷ ﺳﻔﻞ ﻋﻠﻰ اﻟﻴﻤﻴﻦ.

6. ﺣﺎﻓﻈﻮا ﻋﻠﻰ ﺟﻤﻴﻊ اﻟﻘﻄﻊ اﻟﺘﻲ ﺗﻢ ﻓﻜﻬﺎ: ﻋﻨﺪ ﻧﻘﻞ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎن ﻻ ﺧﺮ ﻳﺠﺐ

ﺗﺮآﻴﺐ هﺬه اﻟﻘﻄﻊ ﻣﻜﺎﻧﻬﺎ ﻣﻦ ﺟﺪﻳﺪ.

ﻳﺠﺐ ﻋﺪم ﺗﺮك اﻷ ﻃﻔﺎل اﻟﻠﻌﺐ ﺑﺘﻐﻠﻴﻒ اﻟﺠﻬﺎز.

ﺗﺴﻮﻳﺔ اﻟﺠﻬﺎز

1. رآﺒﻮا ﻏﺴﺎﻟﺔ اﻟﻤﻼ ﺑﺲ ﻋﻠﻰ أرﺿﻴﺔ ﻣﺴﺘﻮﻳﺔ وﺻﻠﺒﺔ ﺑﺪون أرﺗﻜﺎزهﺎ ﻋﻠﻰ ﺣﺎﺋﻂ

أو ﻗﻄﻊ أﺛﺎث أو أي ﺷﻲء اﺧﺮ.

2. اذا آ

ﺎﻧ

ﺖ اﻷ رﺿ

ﻴ

ﺔ ﻏ

ﻴ

ﺮ ﻣ

ﺴ

ﺘ

ﻮﻳ

ﺔ،

ﻳ

ﻤ

ﻜ

ﻨ

ﻜ

ﻢ اﻻ ﺳ

ﺘ

ﻌ

ﺎﻧ

ﺔ ﺑ

ﺎﻷ رﺟ

ﻞ اﻷ ﻣ

ﺎﻣ

ﻴ

ﺔ

اﻟﻤﺘﺤﺮآﺔ واﻟﺘﻲ ﻗﺎﺑﻠﺔ اﻟﺘﻌﺪﻳﻞ ﻓﻲ ارﺗﻔﺎﻋﻬﺎ

وذﻟﻚ ﻻ زاﻟﺔ ﻋﺪم اﺳﺘﻮاء اﻷ رﺿﻴﺔ )اﻇﺮ

اﻟﻰ اﻟﺸﻜﻞ(. زاوﻳﺔ اﻟﻤﻴﻼ ن اﻟﺘﻲ ﻳﻤﻜﻨﻜﻢ

ﻗﻴﺎﺳﺘﻬﺎ ﻋﻠﻰ اﻟﺴﻄﺢ اﻟﻌﻠﻮي ﻟﻠﺠﻬﺎز ﻳﺠﺐ

أن ﻻ ﻳﺰﻳﺪ ﻋﻦ 2 درﺟﺔ.

وﺿ

ﻊ اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﺸ

ﻜ

ﻞ ﻣ

ﺴ

ﺘ

ﻮي ﺗ

ﻌ

ﻤ

ﻞ ﻋ

ﻠ

ﻰ ﺛ

ﺒ

ﺎت اﻟ

ﺠ

ﻬ

ﺎز ﺑ

ﻤ

ﻜ

ﺎﻧ

ﻪ وﻋ

ﺪم ذﺑ

ﺬﺑ

ﺘ

ﻪ، وﻋ

ﺪم

ﺳﻤﺎع اﺻﻮات ﻣﺰﻋﺠﺔ ﺧﻼ ل ﻋﻤﻞ اﻟﺠﻬﺎزأو ﺗﺤﺮك اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎﻧﻪ ﺧﻼ ل ﻋﻤﻞ

اﻟﺠﻬﺎز، ﻓﻲ ﺣﺎﻟﺔ وﺟﻮد ﻣﻜﻴﺖ أو ﺳﺠﺎد ﻋﻠﻰ اﻷ رﺿﻴﺔ ﺗﺤﺖ اﻟﺠﻬﺎز ﻋﻴﺮوا اﻷ رﺟﻞ

ﺗﺤﺖ اﻟﺠﻬﺎز ﺑﺤﻴﺖ ﻳﺘﻢ ﺗﺮك ﻣﺴﺎﻓﺔ ﺑﻴﻦ اﻟﺠﻬﺎز واﻷ رﺿﻴﺔ ﺗﺤﺘﻪ وذﻟﻚ ﻟﺘﺮك ﺣﻴﺰ

ﻟﺪﺧﻮل اﻟﻬﻮاء ﻣﻦ أﺟﻞ اﻟﺘﻬﻮﻳﺔ.

ﺗﻮﺻﻴﻞ اﻟﻤﺎء واﻟﻜﻬﺮﺑﺎء ﺑﺎﻟﺠﻬﺎز

ﺗﻮﺻﻴﻞ ﺧﺮﻃﻮم ﺗﻐﺬﻳﺔ اﻟﺠﻬﺎز ﺑﺎﻟﻤﺎء

1. أدﺧﻠﻮا ﺣﻠﻘﺔ ﻋﺪم ﺗﺴﺮب اﻟﻤﺎء اﻟﻤﺸﺎر

ﻟﻬﺎ ﺑﺎﻟﺤﺮف A ﻓﻲ ﻧﻬﺎﻳﺔ ﺧﺮﻃﻮم وارﺑﻄﻮه

ﺑ

ﻤ

ﺤ

ﺒ

ﺲ اﻟ

ﻤ

ﺎء اﻟ

ﺒ

ﺎرد ﺑ

ﻔ

ﺘ

ﺤ

ﺔ ﻣ

ﺴ

ﻨ

ﻪ ﺑ

ﺴ

ﻦ

3/4 ﻏﺎز )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

ﻗﺒﻞ وﺻﻠﻪ ﺑﺎﻟﺠﻬﺎز اﺗﺮآﻮا اﻟﻤﺎء ﻳﺨﺮج

ﻣﻦ اﻟﻤﺤﺒﺲ ﺣﺘﻰ ﺧﺮوج ﻣﺎء ﺻﺎﻓﻴﺔ ﻣﻦ

اﻟﻤﺤﺒﺲ.

2. اﺷﺒﻜﻮا اﻟﺨﺮﻃﻮم اﻟﺬي ﻳﻐﺬي اﻟﻐﺴﺎﻟﺔ

ﺑﺎﻟﻤﺎء وذﻟﻚ ﺑﺮﺑﻄﻪ ﺑﻤﺪﺧﻞ اﻟﻤﺎء اﻟﻤﻮﺟﻮد

ﻓﻲ ﻇﻬﺮ اﻟﻐﺴﺎﻟﺔ ﻣﻦ اﻟﺨﻠﻒ ﻓﻲ اﻟﻤﻨﻄﻘﺔ

اﻟﻌﻠﻴﺎ ﻋﻠﻰ اﻟﻴﻤﻴﻦ.)اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

3. ﺧ

ﺬوا ﺣ

ﺬرآ

ﻢ ﻣ

ﻦ ﻻ ﻳ

ﻜ

ﻮن اﻟ

ﺨ

ﺮﻃ

ﻮم ﻣ

ﻄ

ﻮي أو ﻣ

ﺨ

ﻨ

ﻮق ﻓ

ﻲ ﻣ

ﻜ

ﺎن ﻣ

ﺎ ﻋ

ﻠ

ﻰ

ﻃﻮل اﻣﺘﺪاده.

ﺿﻐﻂ ﺷﺒﻜﺔ اﻟﻤﺎء ﻳﺠﺐ أن ﺗﻜﻮن ﺑﺎﻟﻘﻴﻢ اﻟﺘﻲ ﺗﻜﻮن ﻣﻌﻄﻴﺔ وﻣﻜﺘﻮﺑﺔ ﻻ ﺋﺤﺔ اﻟﺨﺼﺎﺋﺺ

اﻟﻔﻨﻴﺔ ﻟﻠﺠﻬﺎز)اﻧﻈﺮ اﻟﻰ اﻟﺼﻔﺤﺔ اﻟﺠﺎﻧﺒﻴﺔ(

اذا آﺎن ﻃﻮل ﺧﺮﻃﻮم ﺗﻐﺬﻳﺔ اﻟﻐﺴﺎﻟﺔ ﺑﺎﻟﻤﺎء ﻏﻴﺮ آﺎﻓﻲ اﺳﺘﻌﻴﻨﻮا ﺑﻘﺴﻢ اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ أو

اﻟﻤﺤﻼ ت اﻟﻤﺨﺘﺼﺔ أو ﻓﻨﻲ ﻣﺆهﻞ ﺑﺎﻟﻘﻴﺎم ﺑﻌﻤﻠﻴﺎت اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ.

اوﺻﻠﻮا ﺧﺮﻃﻮم ﺗﻔﺮﻳﻎ اﻟﻤﺎء ﻣﻦ ﺣﻮض

ﻏ

ﺴ

ﻴ

ﻞ اﻟ

ﻐ

ﺴ

ﺎﻟ

ﺔ ﺑ

ﺪون ﻃ

ﻮﻳ

ﻪ، ﺑ

ﻤ

ﺎﺳ

ﻮرة

ﺻ

ﺮف ﻟ

ﻠ

ﻤ

ﺎء، أو ﺑ

ﻤ

ﺼ

ﺮف ﻣ

ﻮﺟ

ﻮد ﻓ

ﻲ

اﻟﺤﺎﺋﻂ ﻋﻠﻰ أن ﻳﻜﻮن ارﺗﻔﺎﻋﻪ ﻣﺎ ﺑﻴﻦ 56

و 001 ﺳﻨﺘﻤﺘﺮ ﻋﻦ ﺳﻄﺢ اﻷ رض

أو ﻗ

ﻮﻣ

ﻮا ﺑ

ﻮﺿ

ﻌ

ﻪ ﻋ

ﻠ

ﻰ ﺣ

ﺎﻓ

ﺔ ﻣ

ﻐ

ﺴ

ﻠ

ﺔ

أو ﺣ

ﻮض ﺣ

ﻤ

ﺎم، ارﺑ

ﻄ

ﻮا اﻟ

ﺨ

ﺮﻃ

ﻮم

ﺑ

ﺤ

ﺎﻣ

ﻞ اﻟ

ﺨ

ﺮﻃ

ﻮم اﻟ

ﺬي ﻳ

ﻜ

ﻮن ﻣ

ﺰود ﻣ

ﻊ

اﻟﺠﻬﺎزﺑﻤﺤﺒﺲ اﻟﻤﺎء )اﻧﻈﺮ اﻟﻰ اﻟﺸﻜﻞ(

اﻟﻄﺮف اﻟﺤﺮ ﻣﻦ اﻟﺨﺮﻃﻮم ﻳﺠﺐ أن ﻻ

ﻳﻜﻮن ﻣﻐﻤﻮر ﻓﻲ اﻟﻤﺎء.

ﻏﻴﺮ ﻣﻨﺼﻮح اﺳﺘﺨﺪام ﺧﺮاﻃﻴﻢ ﺗﻄﻮﻳﻞ ، اذا آﺎن ﻣﻦ اﻟﻀﺮوري اﺳﺘﺨﺪام ﺧﺮاﻃﻴﻢ

اﻟ

ﺘ

ﻄ

ﻮﻳ

ﻞ ﻳ

ﺠ

ﺐ أن ﻳ

ﻜ

ﻮن ﻗ

ﻄ

ﺮ ه

ﺬا اﻟ

ﺨ

ﺮﻃ

ﻮم ﻧ

ﻔ

ﺲ ﻗ

ﻄ

ﺮ اﻟ

ﺨ

ﺮﻃ

ﻮم اﻟ

ﺮﺋ

ﻴ

ﺴ

ﻲ وﻳ

ﺠ

ﺐ

أن ﻻ ﻳﺰﻳﺪ ﻃﻮﻟﻪ ﻋﻦ 051 ﺳﻨﺘﻤﺘﺮ.

اﻟﺘﻮﺻﻴﻞ ﺑﺸﺒﻜﺔ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ

ﻗﺒﻞ ادﺧﺎل ﻗﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( ﺑﻤﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﺗﺄآﺪوا

ﻣﻦ أن:

ﻣﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﻟﻬﺎ ﺧﻂ أرض ﻓﻌﺎل وﺧﺎﺿﻊ اﻟﻰ اﻟﻘﻮاﻧﻴﻦ

ﻣ

ﻘ

ﺒ

ﺲ اﻟ

ﺘ

ﻴ

ﺎر اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ )اﻷ ﻧ

ﺜ

ﻰ( ﻗ

ﺎدر ﻋ

ﻠ

ﻰ ﺗ

ﺤ

ﻤ

ﻞ اﻟ

ﻘ

ﺪرة اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ اﻟ

ﻘ

ﺼ

ﻮى

اﻟ

ﻤ

ﺘ

ﺼ

ﺔ ﻣ

ﻦ ﻗ

ﺒ

ﻞ اﻟ

ﺠ

ﻬ

ﺎزوﻳ

ﻜ

ﻮن ﻣ

ﺸ

ﺎر ﻟ

ﻬ

ﺎ ﻓ

ﻲ ﻻ ﺋ

ﺤ

ﺔ اﻟ

ﺨ

ﺼ

ﺎﺋ

ﺺ اﻟ

ﻔ

ﻨ

ﻴ

ﺔ ﻟ

ﻠ

ﺠ

ﻬ

ﺎز

)اﻧﻈﺮ اﻟﻰ اﻟﺠﺎﻧﺐ(.

ﻓﺮق ﺟﻬﺪ ﺷﺒﻜﺔ اﻟﻜﻬﺮﺑﺎء ﻳﺠﺐ أن ﺗﻜﻮن ﻓﻲ اﻟﻘﻴﻢ اﻟﺘﻲ ﺗﻜﻮن ﻣﻮﺟﻮدة واﻟﻤﺸﺎر ﻟﻬﺎ

ﻓﻲ ﻻ ﺋﺤﺔ اﻟﺨﺼﺎﺋﺺ اﻟﻔﻨﻴﺔ ﻟﻠﺠﻬﺎز )اﻧﻈﺮ اﻟﻰ اﻟﺠﺎﻧﺐ(.

ﻣﻘﺒﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ( ﻣﻼ ﺋﻢ ﻟﻘﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( اﻟﻤﺰود ﻣﻊ

اﻟﻐﺴﺎﻟﺔ ﻓﻲ ﺣﺎﻟﺔ ﻋﺪم ﺗﻮاﻓﻘﻬﻢ ﻗﻮﻣﻮا ﺑﻌﻤﻠﻴﺔ ﺗﻐﻴﻴﺮ اﺣﺪاهﻤﺎ.

ﺟ

ﻬ

ﺎزآ

ﻢ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﻣ

ﺰود ﺑ

ﻘ

ﺎﺑ

ﺲ )اﻟ

ﺬآ

ﺮ( ﻣ

ﺼ

ﻬ

ﻮر وﻗ

ﺎدرﻋ

ﻠ

ﻰ ﺗ

ﺤ

ﻤ

ﻞ ﺗ

ﻴ

ﺎر آ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ

31 أﻣﺒﻴﺮ وﻳﻤﻜﻨﻜﻢ ادﺧﺎل هﺬا اﻟﻘﺎﺑﺲ ﺑﻤﻘﺒﺲ )اﻻ ﻧﺜﻰ( ﻳﺘﻮاﻓﻖ ﻣﻌﺔ ﻟﻼ ﺳﺘﺨﺪام اﻟﻤﺒﺎﺷﺮ،

اﻗﺮؤوا اﻟﺘﻌﻠﻴﻤﺎت اﻟﺘﺎﻟﻴﺔ ﻗﺒﻞ اﺳﺘﺨﺪام اﻟﺠﻬﺎز اﻟﻜﻬﺮﺑﺎﺋﻲ.

اﻧ

ﺘ

ﺒ

ﺎه: اﻟ

ﺠ

ﻬ

ﺎز اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﻳ

ﺠ

ﺐ أن ﻳ

ﻜ

ﻮن ﻣ

ﻮﺻ

ﻮل ﺑ

ﺨ

ﻂ أرض ﻓ

ﻌ

ﺎل، اﻟ

ﻌ

ﻤ

ﻠ

ﻴ

ﺎت

اﻟﻤﺸﺮوﺣﺔ أدﻧﺎه هﻲ ﺗﻌﻠﻴﻤﺎت ﻣﻮﺟﻪ اﻟﻰ ﻓﻨﻲ آﻬﺮﺑﺎﺋﻲ ﻣﺨﺘﺺ.

65 - 100 cm

ﺗﻐﻴﻴﺮ اﻟﻤﻨﺼﻬﺮة )اﻟﻔﻴﻮز(

ﻋ

ﻨ

ﺪ ﺗ

ﻐ

ﻴ

ﺮ اﻟ

ﻤ

ﻨ

ﺼ

ﻬ

ﺮة )اﻟ

ﻔ

ﻴ

ﻮز( اﻟ

ﻤ

ﻌ

ﻄ

ﻮب، اﺳ

ﺘ

ﺨ

ﺪﻣ

ﻮا داﺋ

ﻤ

ﺎ ﻣ

ﻨ

ﺼ

ﻬ

ﺮة 31 اﻣ

ﺒ

ﻴ

ﺮ

ATSA ﺧﺎﺿﻌﺔ ﻟﻠﻤﻘﻴﺎس 2631 SB وأﻋﻴﺪوا ﻏﻄﺎء اﻟﻤﻨﺼﻬﺮة اﻟﻰ ﻣﻜﺎﻧﻪ اﻟﺬي

ﺎن ﻓ

ﻴ

ﻪ، ﻓ

ﻲ ﺣ

ﺎﻟ

ﺔ ﻓ

ﻘ

ﺪان ه

ﺬا اﻟ

ﻐ

ﻄ

ﺎء ﻻ ﺗ

ﺴ

ﺘ

ﺨ

ﺪﻣ

ﻮا اﻟ

ﻘ

ﺎﺑ

ﺲ ﺣ

ﺘ

ﻰ اﻟ

ﺤ

ﺼ

ﻮل ﻋ

ﻠ

ﻰ

هﺬا اﻟﻐﻄﺎء وﺗﺮآﻴﺒﻪ ﻓﻲ ﻣﻜﺎﻧﻪ.

ﺗﻐﻴﻴﺮ ﻏﻄﺎء اﻟﻤﻨﺼﻬﺮات )اﻟﻔﻴﻮزات(:

اذا ﺗﻢ ﺗﻐﻴﻴﺮ ﻏﻄﺎء اﻟﻔﻴﻮزات ﺗﺎآﺪوا ﻣﻦ أن ﻟﻮﻧﻪ هﻮ اﻟﻠﻮن اﻟﺼﺤﻴﺢ واﻟﻤﺸﺎر ﻟﻪ

ﺑﻮاﺳﻄﺔ اﻟﺮﻗﻢ أو اﻟﻜﺘﺎﺑﺔ اﻟﻤﻠﻮﻧﺔ اﻟﻤﻮﺟﻮدة ﻋﻠﻰ ﻗﺎﻋﺪة اﻟﻘﺎﺑﺲ، ﻟﻘﻄﻊ اﻟﻐﻴﺎر، اﺳﺘﻌﻴﻨﻮا

ﻣﺒﺎﺷﺮة ﺑﻘﺴﻢ اﻟﺼﻴﺎﻧﺔ اﻟﻔﻨﻴﺔ اﻟﻘﺮﻳﺐ ﻋﻠﻴﻜﻢ.

ﻓﻚ اﻟﻘﺎﺑﺲ )اﻟﺬآﺮ(:

ﻓﻲ ﺣﺎﻟﺔ أن ﻳﻜﻮن اﻟﺠﻬﺎز ﻣﺰود ﺑﻘﺎﺑﺲ )اﻟﺬآﺮ( ﻻ ﻳﻤﻜﻦ ﻓﻜﻪ ﻷ ﻧﻪ ﻣﺼﻬﻮر وﺗﺮﻳﺪون

ﺗﻤﺮﻳﺮ ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻣﻦ ﺧﻼ ل ﺛﻘﻮب أو ﻓﺘﺤﺎت ﺻﻐﻴﺮة ﻻ ﻳﻤﺮ ﻣﻦ ﺧﻼ ﻟﻬﺎ

اﻟﻘﺎﺑﺲ ﻗﻮﻣﻮا ﺑﺘﻐﻴﻴﺮ اﻟﻘﺎﺑﺲ اﻟﻤﺼﻬﻮر ﺑﻘﺎﺑﺲ ﻳﻤﻜﻦ ﻓﻜﻪ وﺗﺮآﻴﺒﻪ وﻗﺎدر ﻋﻠﻰ ﺗﺤﻤﻞ

31 أﻣﺒﻴﺮ وﻳﺤﻤﻞ اﻟﺸﻌﺎر ISB.

أو

وﺻ

ﻞ ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﺑ

ﻤ

ﻨ

ﺒ

ﻊ اﻟ

ﺘ

ﻴ

ﺎر اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﺑ

ﻮاﺳ

ﻄ

ﺔ ﻣ

ﻔ

ﺘ

ﺎح ﻗ

ﺎدر ﻋ

ﻠ

ﻰ

ﺗ

ﺤ

ﻤ

ﻞ 31 أﻣ

ﺒ

ﻴ

ﺮ )وﺧ

ﺎﺿ

ﻊ ﻟ

ﻠ

ﻤ

ﻘ

ﻴ

ﺎس 3375 SB ( ﻳ

ﻤ

ﻜ

ﻦ اﻟ

ﻮﺻ

ﻮل اﻟ

ﻴ

ﻪ ﺑ

ﺪون

ﺗﺤﺮﻳﻚ اﻟﺠﻬﺎز ﻣﻦ ﻣﻜﺎﻧﻪ.

ازاﻟﺔ اﻟﻘﺎﺑﺲ )اﻟﺬآﺮ(:

ﻗﺒﻞ رﻣﻲ اﻟﻘﺎﺑﺲ اﺟﻌﻠﻮة ﻏﻴﺮ ﻗﺎﺑﻞ ﻟﻼ ﺳﺘﻌﻤﺎل وذﻟﻚ ﺑﻜﺴﺮ رؤوﺳﻪ ﺑﺤﻴﺚ ﻻ ﻳﻤﻜﻦ

ادﺧﺎﻟﻪ داﺧﻞ ﺛﻘﻮب ﻣﻘﺒﺲ )اﻻ ﻧﺜﻰ( ﺑﺸﻜﻞ ﻋﻔﻮي.

ﺗﻌﻠﻴﻤﺎت ﻣﻦ أﺟﻞ ﺗﻮﺻﻴﻞ ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺑﻘﺎﺑﺲ )اﻟﺬآﺮ(:

ﻣﻬﻢ: أﻟﻮان اﻷ ﺳﻼ ك اﻟﺘﻐﺬﻳﻪ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺗﺸﻴﺮ اﻟﻰ اﻟﺘﺎﻟﻲ:

أﺻﻔﺮ/أﺧﻀﺮ ﺧﻂ أرض

ازرق ﻣﺤﺎﻳﺪ )ﻧﻴﻮﺗﺮل(

ﺑﻨﻲ ﺗﻐﺬﻳﺔ

وﻷ ن أﻟ

ﻮان ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﻳ

ﻤ

ﻜ

ﻦ أن ﻻ ﻳ

ﻄ

ﺎﺑ

ﻘ

ﻮا اﻻ ﺷ

ﺎرات اﻟ

ﻤ

ﻠ

ﻮﻧ

ﺔ اﻟ

ﺘ

ﻲ

ﺗﻌﺮف ﻣﺮاﺑﻂ اﻟﻘﺎﺑﺲ، اﺗﺒﻌﻮا اﻟﺨﻄﻮات اﻟﺘﺎﻟﻴﺔ:

أوﺻﻠﻮا اﻟﺴﻠﻚ اﻷ ﺻﻔﺮ/اﻷ ﺧﻀﺮ ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف E أو ﺑﺎﻟﺸﻌﺎر

أو

اﻟﻠﻮن اﻷ ﺧﻀﺮ أو اﻷ ﺻﻔﺮ/اﻷ ﺧﻀﺮ

أوﺻﻠﻮا اﻟﺴﻠﻚ اﻟﺒﻨﻲ ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف L أو ﺑﺎﻟﻠﻮن اﻷ ﺣﻤﺮ.

أوﺻﻠﻮا اﻟﺴﻠﻚ اﻷ زرق ﺑﺎﻟﻤﺮﺑﻂ اﻟﻤﺸﺎر ﻟﻪ ﺑﺎﻟﺤﺮف N أو ﺑﺎﻟﻠﻮن اﻷ ﺳﻮد.

اذا اﺳﺘﺨﺪﻣﺘﻢ ﻗﺎﺑﺲ )اﻟﺬآﺮ( 31 أﻣﺒﻴﺮ )3631 SB( رآﺒﻮا ﻣﻨﺼﻬﺮة )ﻓﻴﻮز( 31

أﻣﺒﻴﺮ ﻓﻲ اﻟﻤﻘﺒﺲ أو ﻓﻲ اﻟﻤﻬﺎي

أو ﻋﻠﻰ ﻟﻮﺣﺔ اﻟﺘﻮزﻳﻊ.

ﻓ

ﻲ ﺣ

ﺎﻟ

ﺔ اﻟ

ﺸ

ﻚ ﺑ

ﺎﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﻟ

ﺠ

ﻬ

ﺎزآ

ﻢ اﺳ

ﺘ

ﺪﻋ

ﻮا ﻓ

ﻨ

ﻲ آ

ﻬ

ﺮﺑ

ﺎﺋ

ﻲ ﻣ

ﺨ

ﺘ

ﺺ ﻗ

ﺒ

ﻞ

وﺻﻞ اﻟﺠﻬﺎز ﺑﻤﻨﺒﻊ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ.

وﺻﻞ ﻗﺎﺑﺲ )اﻟﺬآﺮ( ﺑﺪﻳﻞ:

أﻟﻮان اﻷ ﺳﻼ ك اﻟﺘﻐﺬﻳﻪ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﺗﺸﻴﺮ اﻟﻰ اﻟﺘﺎﻟﻲ:

ازرق ﻣﺤﺎﻳﺪ )ﻧﻴﻮﺗﺮل( )N(

ﺑﻨﻲ ﺗﻐﺬﻳﺔ )L(

أﺻﻔﺮ/أﺧﻀﺮ ﺧﻂ أرض )E(

ازاﻟﺔ اﻟﺠﻬﺎز اﻟﻜﻬﺮﺑﺎﺋﻲ اﻟﺒﻴﺘﻲ:

ﻋﻨﺪ رﻣﻲ ﺟﻬﺎز آﻬﺮﺑﺎﺋﻲ ﺑﻴﺘﻲ، ﻳﺠﺐ ازاﻟﺔ ﻗﺎﺑﺲ اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻟﺬآﺮ( وذﻟﻚ

ﺑ

ﻘ

ﺺ ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﺑ

ﺄﻗ

ﺮب ﻧ

ﻘ

ﻄ

ﺔ ﻣ

ﻤ

ﻜ

ﻨ

ﺔ ﻣ

ﻦ اﻟ

ﻘ

ﺎﺑ

ﺲ وﻗ

ﻮﻣ

ﻮا ﺑ

ﺘ

ﺤ

ﻄ

ﻴ

ﻢ

رؤوس اﻟﻘﺎﺑﺲ آﻤﺎ ذآﺮ ﺳﺎﺑﻘﺎ.

VERDE &

GIALLO

MARRONE

BLU

fusibile

13 ampere

SERRAFILO

CROSSBAR

ﻣ

ﻨ

ﺼ

ﻬ

ﺮة 31

أﻣﺒﻴﺮ

ﻣﺮﺑﻂ ﺳﻠﻚ

أﺧﻀﺮ

أﺻﻔﺮ

ﺑﻨﻲ

أزرق

!اﻟﻐﺴﺎﻟﺔ ﻻ ﺗﻮﺿﻊ ﻓﻲ اﻟﺨﺎرج ﺣﺘﻰ ﻟﻮ آﺎن اﻟﻤﻜﺎن ﻣﻐﻄﻰ وذﻟﻚ ﻷ ﻧﻪ ﻣﻦ اﻟﺨﻄﺮ ﺗﺮك

اﻟﺠﻬﺎز ﺗﺤﺖ ﻋﻮاﻣﻞ اﻟﻄﻘﺺ ﻣﺜﻞ اﻟﻤﻄﺮ ﺑﺮق رﻋﺪ اﻟﻰ اﺧﺮه.

! ﺑ

ﻌ

ﺪ اﻻ ﻧ

ﻬ

ﺎء ﻣ

ﻦ ﺗ

ﺮآ

ﻴ

ﺐ اﻟ

ﺠ

ﻬ

ﺎز ﻳ

ﺠ

ﺐ أن ﻳ

ﻜ

ﻮن ﻣ

ﻦ اﻟ

ﺴ

ﻬ

ﻞ اﻟ

ﻮﺻ

ﻮل اﻟ

ﻰ ﻣ

ﻘ

ﺒ

ﺲ

اﻟﺘﻴﺎر اﻟﻜﻬﺮﺑﺎﺋﻲ )اﻷ ﻧﺜﻰ(.

! ﻻ ﺗﺴﺘﺨﺪﻣﻮا ﻣﻬﺎﻳﺌﺎت او ﻣﻘﺒﺲ ﻣﺘﻌﺪد اﻟﺜﻘﻮب أو اﺳﻼ ك ﺗﻄﻮﻳﻞ.

! ﺳﻠﻚ اﻟﺘﻐﺬﻳﺔ اﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻳﺠﺐ أن ﻻ ﻳﻜﻮن ﻣﻄﻮي أو ﻣﺤﺸﻮر ﺑﻴﻦ اﻷ ﺛﺎث.

!ﺳ

ﻠ

ﻚ اﻟ

ﺘ

ﻐ

ﺬﻳ

ﺔ اﻟ

ﻜ

ﻬ

ﺮﺑ

ﺎﺋ

ﻴ

ﺔ ﻳ

ﺠ

ﺐ أن ﻳ

ﺘ

ﻢ ﺗ

ﺒ

ﺪﻳ

ﻠ

ﻪ وﻗ

ﺖ اﻟ

ﺤ

ﺎﺟ

ﺔ ﻓ

ﻘ

ﻂ ﻣ

ﻦ ﻗ

ﺒ

ﻞ ﻓ

ﻨ

ﻲ ﻣ

ﺨ

ﺘ

ﺺ

وﻣﺆهﻞ ﻟﻠﻘﻴﺎم ﺑﻬﺬا.

اﻧ

ﺘ

ﺒ

ﺎه: اﻟ

ﺸ

ﺮآ

ﺔ اﻟ

ﺼ

ﺎﻧ

ﻌ

ﺔ ﺗ

ﺴ

ﻘ

ﻂ ﻋ

ﻦ ﻧ

ﻔ

ﺴ

ﻬ

ﺎ أي ﻣ

ﺴ

ﺆوﻟ

ﻴ

ﺔ ﻋ

ﻦ أﺿ

ﺮار ﻗ

ﺪ ﺗ

ﺤ

ﺼ

ﻞ ﻣ

ﻦ

ﻋﺪم اﺗﺒﺎع واﺣﺘﺮام هﺬه ﻗﻮاﻋﺪ اﻷ ﻣﻦ.

أول دورة ﻏﺴﻴﻞ

ﺑﻌﺪ اﻻ ﻧﺘﻬﺎء ﻣﻦ ﻋﻤﻠﻴﺔ ﺗﺮآﻴﺐ اﻟﺠﻬﺎز، وﻗﺒﻞ اﺳﺘﺨﺪاﻣﻪ، ﻗﻮﻣﻮا ﺑﻌﻤﻠﻴﺔ ﻏﺴﻴﻞ ﻣﺴﺘﺨﺪﻣﻴﻦ

ﻣ

ﺴ

ﺤ

ﻮق ﻏ

ﺴ

ﻴ

ﻞ وﺑ

ﺪون ﻣ

ﻼ ﺑ

ﺲ داﺧ

ﻞ اﻟ

ﻐ

ﺴ

ﺎﻟ

ﺔ، ﻣ

ﺴ

ﺘ

ﺨ

ﺪﻣ

ﻴ

ﻦ ﺑ

ﺮﻧ

ﺎﻣ

ﺞ اﻟ

ﻐ

ﺴ

ﻴ

ﻞ ﻋ

ﻠ

ﻰ 09

درﺟﺔ ﻣﺌﻮﻳﺔ ﺑﺪون ﻋﻤﻠﻴﺔ ﻏﺴﻴﻞ ﺑﺪاﺋﻴﺔ.

ﻣﻮاﺻﻔﺎت ﻓﻨﻴﺔ

اﻟﻤﺪﻳﻞ

28 IW

اﻷ ﺑﻌﺎد

اﻟﻌﺮض 5.95 ﺳﻨﺘﻤﺘﺮ

اﻻ رﺗﻔﺎع 58 ﺳﻨﺘﻤﺘﺮ

اﻟﻌﻤﻖ 5.25 ﺳﻨﺘﻤﺘﺮ

اﻟﻘﺪرة

ﻣﻦ 1 اﻟﻰ 5 آﻐﻢ

اﻟﺘﻮﺻﻴﻼ ت اﻟﻜﻬﺮﺑﺎﺋﻴﺔ

ﻓﺮق ﺟﻬﺪ 022/032 ﻓﻮﻟﺖ 06 هﻴﺮﺗﺰ

اﻟﻘﺪرة اﻟﻘﺼﻮى اﻟﻤﻤﺘﺼﺔ ﻣﻦ ﻗﺒﻞ اﻟﺠﻬﺎز 0571 واط

اﻟﺘﻮﺻﻴﻼ ت اﻟﻬﻴﺪروﻟﻴﻜﻴﺔ

اﻟﻀﻐﻂ اﻟﻘﺼﻮى 1 ﻣﻠﺒﺴﻜﺎل )01 ﺑﺎر(

اﻟﻀﻐﻂ اﻟﺪﻧﻴﺎ 50.0 ﻣﻴﻠﻴﺒﺴﻜﺎل )5.0 ﺑﺎر(

ﻗﺪرة ﺣﻮض اﻟﻐﺴﻴﻞ 04 ﻟﺘﺮ

ﺳﺮﻋﺔ اﻟﻌﺼﺮ اﻟﺪوراﻧﻴﺔ

ﺣﺘﻰ 008 دورة ﻓﻲ اﻟﺪﻗﻴﻘﺔ

ﺑﺮاﻣﺞ ﺗﺠﺮﺑﺔ اﻟﺠﻬﺎز ﺣﺴﺐ

اﻟﻘﻮاﻋﺪ 654CEI

ﺑ

ﺮﻧ

ﺎﻣ

ﺞ 3، درﺟ

ﺔ ﺣ

ﺮارة 06 درﺟ

ﺔ ﻣ

ﺌ

ﻮﻳ

ﺔ، ﺗ

ﻤ

ﺖ اﻟ

ﺘ

ﺠ

ﺮﺑ

ﺔ

ﺑﺤﻤﻞ ﻏﺴﻴﻞ 5 آﻐﻢ

هﺬا اﻟﺠﻬﺎز ﻳﻄﺎﺑﻖ اﻟﻤﻮاﺻﻔﺎت اﻟﻤﻄﻠﻮﺑﺔ ﻣﻦ ﺳﻮق اﻟﺪول

اﻷ ورﺑﻴﺔ اﻟﻤﺸﺘﺮآﺔ:

- ﺑﻤﺎ ﻳﺘﻌﻠﻖ ﺑﻔﺮق ﺟﻬﺪ ﻣﻨﺨﻔﺾ

- ﺑﻤﺎ ﻳﺘﻌﻠﻖ اﻟﺘﻮاﻓﻖ اﻟﻜﻬﺮوﻣﻐﻨﺎﻃﻴﺴﻲ

ﺲﺑ ﻼﻤﻟا ﺔﻟﺎﺴﻏ ﻒﺻو

ﻟ

ﻮﺣ

ﺔ اﻟ

ﻘ

ﻴ

ﺎدة

ﻣﻘﺒﺾ

اﻟﺒﺮاﻣﺠﺔ

زر

ﺗﺸﻐﻴﻞ/ اﻃﻔﺎء

أزر

وﻇﺎﺋﻒ

ﻣﻘﺒﺾ

درﺟﺔ اﻟﺤﺮارة

ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ

ﺣﻮض ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ ﻟﻮﺿﻊ ﻣﺴﺎﺣﻴﻖ اﻟﻐﺴﻴﻞ واﻟﻤﺴﺎﺣﻴﻖ اﻻ ﺿﺎﻓﻴﺔ )اﻧﻈﺮ

ﺻﻔﺤﺔ رﻗﻢ 42(

أزرار اﻟﻮﻇﺎﺋﻒ ﻻ ﺧﺘﻴﺎر اﻟﻮﻇﺎﺋﻒ اﻟﺘﻲ ﺗﻜﻮن ﻣﺰودة ﺑﻬﺎ ﻏﺴﺎﻟﺔ اﻟﻤﻼ ﺑﺲ

ﻣﻘﺒﺾ درﺟﺔ اﻟﺤﺮارة ﻟﻮﺿﻊ درﺟﺔ ﺣﺮارة اﻟﻐﺴﻴﻞ أو اﻟﻘﻴﺎم ﺑﻌﻤﻠﻴﺔ اﻟﻐﺴﻴﻞ

ﺑﻤﺎء ﺑﺎرد )اﻧﻈﺮ اﻟﻰ ﺻﻔﺤﺔ 32(

ﻣ

ﺼ

ﺒ

ﺎح اﻧ

ﺬارﺑ

ﺎب اﻟ

ﻐ

ﺴ

ﺎﻟ

ﺔ ﻣ

ﻘ

ﻔ

ﻞ ﻟ

ﻔ

ﻬ

ﻢ اذا آ

ﺎن ﻣ

ﻦ اﻟ

ﻤ

ﻜ

ﻦ ﻓ

ﺘ

ﺢ ﺑ

ﺎب اﻟ

ﻐ

ﺴ

ﺎﻟ

ﺔ

)اﻧﻈﺮ اﻟﻰ ﺻﻔﺤﺔ 12(

زر ﺗﺸﻐﻴﻞ/اﻃﻔﺎء FFO/NO ﻟﺘﺸﻐﻴﻞ واﻃﻔﺎء ﻏﺴﺎﻟﺔ اﻟﻤﻼ ﺑﺲ.

اﻃﻔﺎء اﻟﺠﻬﺎز ﻻ ﻳﻠﻐﻲ اﻟﺒﺮﻧﺎﻣﺞ اﻟﻤﺨﺘﺎر

زر ﺗﺸﻐﻴﻞ/اﻃﻔﺎء FFO/NO ﻟﻔﻬﻢ اذا ﻣﺎ آﺎﻧﺖ اﻟﻐﺴﺎﻟﺔ ﺗﻌﻤﻞ واذا اﻟﺒﺮﻧﺎﻣﺞ اﻟﻤﺨﺘﺎر

ﻗﺪ ﺗﻢ ﻗﺒﻮﻟﻪ ﻣﻦ ﻗﺒﻞ اﻟﺠﻬﺎز )اﻧﻈﺮ ﺻﻔﺤﺔ 12(

ﻣﻘﺒﺾ اﻟﺒﺮﻣﺠﺔ ﻟﻮﺿﻊ اﻟﺒﺮاﻣﺞ )اﻧﻈﺮ ﺻﻔﺤﺔ 22(

ﻣ

ﻼ ﺣ

ﻈ

ﺔ: ﺑ

ﻌ

ﺪ وﺿ

ﻊ دوره اﻟ

ﻐ

ﺴ

ﻴ

ﻞ اﻟ

ﻤ

ﺮاد اﺳ

ﺘ

ﺨ

ﺪاﻣ

ﻬ

ﺎ وﻗ

ﺒ

ﻮل ه

ﺬا اﻟ

ﺒ

ﺮﻧ

ﺎﻣ

ﺞ ﻣ

ﻦ ﻗ

ﺒ

ﻞ

اﻟﻐﺴﺎﻟﺔ، ﺗﻐﻴﻴﺮ وﺿﻊ ﻣﻘﺒﺾ اﺧﺘﻴﺎر اﻟﺒﺮاﻣﺞ ﻻ ﻳﻜﻮن ﻟﻪ أي ﺗﺄﺛﻴﺮﻋﻠﻰ اﻟﺒﺮﻧﺎﻣﺞ اﻟﺬي ﻗﺪ

ﺑﺪأ اﻟﻌﻤﻞ )ﻣﺎ ﻋﺪى اﻟﻮﺿﻊ

)اﻃﻔﺎء/اﻟﻐﺎء teseR/potS(.

ﻗﻮﻣﻮا ﺑﺘﺪوﻳﺮ هﺬا اﻟﻤﻘﺒﺾ ﻓﻘﻂ ﺑﺎﺗﺠﺎه دوران ﻋﻘﺎرب اﻟﺴﺎﻋﺔ.

ﻣﺼﺒﺎح اﻧﺬار

ﺑﺎب اﻟﻐﺴﺎﻟﺔ ﻣﻘﻔﻞ

ﻣﺼﺒﺎح

ﺗﺸﻐﻴﻞ/ اﻃﻔﺎء

Page is loading ...

Indesit WI 82 (EX) 60 Hz User guide

Brand: Indesit

Model: WI 82 (EX) 60 Hz

Category: Washing machines

Type: User guide

Download PDF

report

in other languages

français: Indesit WI 82 (EX) 60 Hz Mode d'emploi

Indesit WI 82 (EX) 60 Hz User guide

Indesit WI 82 (EX) 60 Hz User guide

in other languages

Related papers

Other documents