Grizzly SB1056F Owner's manual

Hundreds of Thousands of Lathes Sold With a Tradition of

Q

uality Since 1906!

TURN-NADO

®

GEARHEAD

LATHE w/DRO

MODEL SB1046PF 21" X 60" MODEL SB1056F 18" X 40"

MODEL SB1047PF 21" X 80" MODEL SB1057F 18" X 60"

MODEL SB1048PF 21" X 120" MODEL SB1058F 18" X 80"

OWNER'S MANUAL

Customer Service

We stand behind our machines. If you have any service questions, parts requests or general questions

about your purchase, feel free to contact us.

South Bend Lathe Co.

P.O. Box 2027

Bellingham, WA 98227

Fax: (360) 676-1075 (International)

Fax: (360) 734-1639 (USA Only)

Email: [email protected]

Updates

For your convenience, any updates to this manual will be available to download free of charge

through our website at:

www.southbendlathe.com

Scope of Manual

This manual helps the reader understand the machine, how to prepare it for operation, how to control

it during operation, and how to keep it in good working condition. We assume the reader has a basic

understanding of how to operate this type of machine, but that the reader is not familiar with the

controls and adjustments of this specific model. As with all machinery of this nature, learning the

nuances of operation is a process that happens through training and experience. If you are not an

experienced operator of this type of machinery, read through this entire manual, then learn more

from an experienced operator, schooling, or research before attempting operations. Following this

advice will help you avoid serious personal injury and get the best results from your work.

Manual Feedback

We've made every effort to be accurate when documenting this machine. However, errors sometimes

happen or the machine design changes after the documentation process—so the manual may not

exactly match your machine. If a difference between the manual and machine leaves you in doubt,

contact our customer service for clarification.

We highly value customer feedback on our manuals. If you have a moment, please share your

experience using this manual. What did you like about it? Is there anything you would change to

make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use?

South Bend Lathe, Inc.

C

/O Technical Documentation Manager

P.O. Box 2027

Bellingham, WA 98227

Email: [email protected]

Table of Contents

INTRODUCTION ....................................................3

About This Machine .............................................3

Foreword .............................................................3

Capabilities .........................................................3

Features .............................................................. 3

General Identiﬁcation ..........................................4

Controls & Components.......................................5

Master Power Switch ...........................................5

Headstock ........................................................... 5

Control Panel ......................................................6

Carriage .............................................................. 6

Carriage Feed Clutch Knob ..................................7

Tailstock ............................................................. 7

Safety Foot Brake ................................................8

SB1046PF, SB1047PF, SB1048PF .......................9

Product Speciﬁcations .......................................13

SB1056F, SB1057F, SB1058F ............................13

SAFETY ................................................................17

Understanding Risks of Machinery .................. 17

Basic Machine Safety ........................................ 17

Additional Metal Lathe Safety ..........................19

Additional Chuck Safety....................................20

PREPARATION ....................................................21

Preparation Overview ........................................21

Things You'll Need ............................................. 21

Power Supply Requirements .............................22

Availability ........................................................22

Full-Load Current Rating .................................. 22

Circuit Requirements .........................................22

Grounding Requirements ................................... 23

Unpacking ..........................................................24

Inventory ............................................................24

Cleaning & Protecting .......................................25

Physical Environment ........................................ 26

Electrical Installation ........................................ 26

Lighting ............................................................ 26

Weight Load ...................................................... 26

Space Allocation ................................................ 26

Lifting & Moving ................................................27

Leveling & Mounting ......................................... 28

Leveling ............................................................ 28

Bolting to Concrete Floors .................................. 29

Assembly ............................................................29

Lubricating Lathe .............................................. 30

Adding Coolant .................................................. 30

Power Connection .............................................. 30

Test Run ............................................................. 32

Spindle Break-In ................................................ 35

Recommended Adjustments .............................. 35

OPERATION ........................................................36

Operation Overview ........................................... 36

Chuck & Faceplate Mounting ........................... 37

Installation & Removal Devices ........................37

Chuck Installation ............................................. 38

Registration Marks ............................................ 39

Chuck Removal ..................................................39

Scroll Chuck Clamping ...................................... 40

4-Jaw Chuck .......................................................40

Mounting Workpiece .......................................... 40

Faceplate ............................................................41

Tailstock ............................................................. 42

Positioning Tailstock ......................................... 42

Using Quill ........................................................ 42

Installing Tooling ..............................................43

Removing Tooling ..............................................44

Offsetting Tailstock ...........................................44

Aligning Tailstock to Spindle Centerline ............45

Centers ...............................................................46

Dead Centers .....................................................46

Live Centers ......................................................47

Mounting Dead Center in Spindle ...................... 47

Removing Center from Spindle ...........................47

Mounting Center in Tailstock .............................47

Removing Center from Tailstock ........................48

Mounting Workpiece Between Centers ............... 48

Steady Rest ........................................................ 49

Follow Rest ......................................................... 50

Carriage & Compound Rest Locks .................... 50

Compound Rest .................................................. 50

Four-Way Tool Post ...........................................51

Installing Tool ................................................... 51

Aligning Cutting Tool with Spindle Centerline ...51

Micrometer Stop.................................................52

Manual Feed ......................................................53

Carriage Handwheel .......................................... 53

Cross Slide Handwheel ...................................... 53

Compound Rest Handwheel ...............................53

Spindle Speed ..................................................... 53

Determining Spindle Speed ................................53

Setting Spindle Speed ........................................ 54

16" South Bend Precision Toolroom Lathe

(Circa 1958)

Power Feed .........................................................54

Power Feed Controls .......................................... 55

Setting Power Feed Rate .................................... 57

End Gears ...........................................................58

Standard End Gear Conﬁguration ...................... 58

Alternate End Gear Conﬁguration .....................58

Threading Controls ............................................ 59

Headstock & Gearbox Threading Controls ..........59

Apron Controls ..................................................60

Thread Dial ....................................................... 61

Thread Dial Chart .............................................61

Chip Drawer ....................................................... 63

Coolant System ..................................................63

Rod Support........................................................64

ACCESSORIES ...................................................65

MAINTENANCE ...................................................66

Maintenance Schedule ....................................... 66

Cleaning & Protecting .......................................66

Maintenance Chart ............................................67

Lubrication .........................................................68

Headstock ......................................................... 68

Quick-Change Gearbox ...................................... 69

Apron ................................................................ 70

One-Shot Oiler ..................................................71

Longitudinal Leadscrew ..................................... 72

Ball Oilers .........................................................72

End Gears .........................................................73

Coolant System Service .....................................74

Hazards.............................................................74

Adding Fluid .....................................................75

Changing Coolant ..............................................75

Machine Storage ................................................ 76

SERVICE ..............................................................77

Backlash Adjustment ........................................ 77

Compound Rest .................................................77

Cross Slide ........................................................ 77

Leadscrew End Play Adjustment ......................78

Gib Adjustment .................................................. 78

Half Nut Adjustment .........................................80

V-Belts ................................................................ 80

Spindle Clutch Adjustment ............................... 81

Leadscrew Shear Pin Replacement ..................84

Gap Insert Removal & Installation ..................86

Gap Removal ..................................................... 86

Gap Installation ................................................ 87

TROUBLESHOOTING .........................................88

ELECTRICAL ........................................................91

Electrical Safety Instructions ...........................91

Correcting Phase Polarity ................................. 92

Wiring Overview ................................................93

Component Location Index................................94

Electrical Cabinet Wiring ..................................95

Spindle Motor ..................................................... 97

Coolant Pump ..................................................... 97

Control Panel .....................................................98

Additional Components ..................................... 99

Power Supply Connection .................................. 99

PARTS ................................................................100

Headstock Housing .......................................... 100

Headstock Gears ..............................................103

Gearbox ............................................................ 107

End Gears .........................................................115

Motor & Headstock Oil System ....................... 116

Saddle & Cross Slide .......................................118

Tool Post & Compound Rest ............................ 121

Bed & Shafts .................................................... 122

Stands & Panels

(SB1046PF-47PF, SB1056F-58F) ................... 124

Stand & Panels (SB1048PF) ........................... 126

Brake ................................................................128

Tailstock ........................................................... 129

Thread Dial ...................................................... 130

Micrometer Stop...............................................130

Steady Rest ...................................................... 131

Follow Rest ....................................................... 131

Electrical Cabinet & Control Panel ................ 132

Accessories ....................................................... 133

Front Machine Labels ......................................134

Rear Machine Labels .......................................135

WARRANTY .......................................................137

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-3-

INTRODUCTION

About This Machine

Foreword

"The screw cutting engine lathe is the oldest and

most important of machine tools and from it all

other machine tools have been developed. It was

the lathe that made possible the building of the

steamboat, the locomotive, the electric motor, the

automobile and all kinds of machinery used in

industry. Without the lathe our great industrial

progress of the last century would have been

impossible." —How To Run a Lathe, 15th

Edition, South Bend Lathe.

The lathe represented in this manual is a

modern day version of the screw cutting lathes

that trace their roots back to the 1700's, which

were themselves technological improvements of

the bow lathe that can be traced back thousands

of years to the ancient Egyptians.

Now, almost 300 years later, these modern

"screw cutting" lathes are not just a piece of

refined machinery, but a culmination of human

ingenuity and knowledge embodied into the

design and synergy of thousands of interworking

parts—some of which represent the life's work

and dreams of many inventors, mechanical

engineers, and world-class machinists—including

the likes of Leonardo da Vinci, Henry Maudsley,

and the founders of South Bend Lathe, John and

Miles O'Brien.

And now the torch is passed to you—to take

the oldest and most important type of machine

tool—and carry on the tradition. As the operator

of a South Bend Lathe, you now join the ranks

of some very famous and important customers,

such as Henry Ford, who used the machines he

purchased to help him change the world.

Capabilities

These Turn-Nado

®

Gearhead Lathes are built

for daily use in a busy industrial setting.

Loaded with many nice features and high-

precision parts, these lathes excel at making fine

tools, dies, thread gauges, jigs, and precision

test gauges—however, they are by no means

delicate. Thick castings, heavy weight, and

quality construction throughout provide the

necessary brawn for demanding production and

manufacturing tasks.

Features

These 16-Speed Gearhead Lathes are packed

with standard features and equipment, such

as a complete coolant system, easy-to-clean

chip drawer, one-shot way lubrication system,

included steady and follow rests, chuck guard,

adjustable work lamp, foot brake, powered

cross feed, 3- and 4-jaw chucks, faceplate, and

premium Allen-Bradley contactors, thermal

relays, and fuse system.

Spindle speeds are controlled by convenient

headstock levers, which allow the operator to

quickly set the spindle speed within the available

range of 20–1600 RPM.

The beds of these lathes are constructed with

Meehanite castings that are hardened and

precision-ground in the traditional three V-way

prismatic design—long used on South Bend

Lathes for its accuracy, durability, and rigidity.

The headstocks feature quick-change gear levers

and the carriages include an adjustable clutch

that disables automatic carriage feed when it

contacts the included feed stop or in the event of

a crash.

These lathes

feature a spindle clutch that allows

the operator to switch between forward and reverse

without shutting down the motor—a great time saver

.

To further ensure a high degree of accuracy,

these lathes are equipped with high-quality

German spindle bearings and a Fagor 2-Axis

DRO. The spindles are D1-8 camlock with an

MT#7 taper and 3.15" bore. The tailstocks have

an MT#5 taper and 6.5" of quill travel.

-4-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

General Identiﬁcation

K. Tailstock w/MT#5 Quill

L. Rod Support (SB1047PF, -48PF, -58F only)

M. Leadscrew

N. Feed Rod

O. Spindle Rod

P. Chip Drawer

Q . Safety Foot Brake

R. Carriage

S. Micrometer Stop

T. Headstock Spindle Lever

A. Quick-Change Gearbox Controls

B. Headstock Controls

C. D1-8 Camlock MT#7 Spindle

D. Chuck Guard w/Safety Switch

E. Follow Rest

F. 4-Way Tool Post

G. Halogen Work Lamp

H. Steady Rest

I. Coolant Nozzle & Valve

J. Fagor DRO Control Panel

Serious personal injury could occur if

you connect the machine to power before

completing the setup process. DO NOT

connect power until instructed to do so later

in this manual.

Untrained users have an increased risk

of seriously injuring themselves with this

machine. Do not operate this machine until

you have understood this entire manual and

received proper training.

Figure 1. General identification (Model SB1058F shown).

A

B

C

D

E

F

G

H

I

K

J

L

M

N

O

P

Q

R

ST

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-5-

INTRODUCTION

Refer to Figures 2–9 and the following

descriptions to become familiar with the features

and basic controls of this lathe. This knowledge

will be necessary to properly set up the lathe for

the test run and spindle break-in.

Controls &

Components

Master Power Switch

The rotary switch shown in Figure 2 toggles

incoming power ON and OFF to the lathe

controls. It also prevents the electrical cabinet

door from being opened when the switch is ON.

To reduce the risk of

serious injury when using

this machine, read and

understand this entire

manual before beginning any

lathe operations.

Turning the master power switch to OFF is not

a safe alternative to completely disconnecting

the machine from power when wiring,

servicing, or making repairs.

Headstock

A. Quick Change Gearbox Levers: Controls the

leadscrew and feed rod speed for threading

and feed operations.

B. Headstock Feed Direction Lever: Controls

the direction that the leadscrew and feed rod

rotate.

C. Gearbox Range Lever: Shifts the quick-

change gearbox into low range, neutral, or

high range.

D. Spindle Speed Lever: Selects one of the four

spindle speeds within the available range.

E. Spindle Speed Range Lever: Selects one of

four spindle speed ranges.

F. Threading and Feed Charts: Displays the

necessary configurations of the gearbox

levers and end gears for different threading

or feeding options.

Figure 2. Location of the master power switch.

Master Power

Switch

Figure 3. Headstock controls.

A

C

F

B

D

E

-6-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

Control Panel

G. Power Light: Illuminates when lathe controls

are receiving power.

H. Coolant Pump OFF & ON Buttons: Control

the coolant pump motor.

I. Spindle Motor OFF & ON Buttons: Controls

the spindle motor.

J. STOP Button: Stops all machine functions.

Twist clockwise to reset.

Carriage

K. Carriage Handwheel: Moves the carriage

along the bed. Can be disengaged during

power feed operations to prevent an

entanglement hazard.

L. Cross Slide Handwheel: Moves the cross

slide toward and away from the workpiece.

M. Compound Rest Handwheel: Moves the tool

toward and away from the workpiece at the

preset angle of the compound rest.

N. 4-Way Tool Post: Mounts up to four cutting

tools at once that can be individually indexed

to the workpiece.

O. Coolant Flow Control Lever: Controls the

flow of coolant from the nozzle.

P. One-Shot Oiler: Draws oil from the apron

reservoir to lubricate the carriage ways

through various oil ports.

Q . Half Nut Lever: Engages/disengages the half

nut for threading operations.

R. Carriage Lock: Secures the carriage in place

when the carriage should not move.

S. Thread Dial and Chart: Dial indicates when

to engage the half nut during threading

operations. Chart indicates on which thread

dial reading to engage the half nut for

specific inch thread pitches.

T. Spindle Lever: Starts, stops and reverses

direction of spindle rotation.

U. Feed ON/OFF Lever: Engages/disengages

power feed.

V. Apron Feed Direction Knob: Changes

direction of carriage or the cross slide feed

without having to stop the lathe and move

the headstock feed direction lever.

W. Feed Selection Knob: Selects the carriage or

cross slide for power feed.

K

M

Figure 5. Carriage controls.

L

N

R

S

O

P

Q

U

V

W

T

Figure 4. Control panel.

G

H I J

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-7-

INTRODUCTION

Carriage Feed Clutch Knob

X. Carriage Feed Clutch Knob: Adjusts how

easily the carriage clutch will disengage

automatic feeding when the carriage

contacts a feed stop or in the event of a

crash. Tightening this knob all the way

disables the carriage clutch completely.

Tailstock

Figure 6. Adjustable carriage feed clutch knob.

X

AB. Tailstock Handwheel: Moves the quill toward

or away from the spindle. The graduated

dial has 0.001" increments with one full

revolution equaling 0.200" of quill travel.

AC. Tailstock Gib Screws: Adjust the tapered gib

to control tailstock offset accuracy.

AD. Tailstock Offset Screws: Adjust the

tailstock offset left or right from the spindle

centerline.

Figure 7. Tailstock controls.

Y

Z

AA

AB

AC

AD

Y. Quill: The quill has an MT#5 taper, metric

and inch scale, and a drift slot to remove

tight-fitting tooling.

Z. Quill Lock Lever: Secures the quill in

position.

AA. Tailstock Lock Lever: Secures the tailstock in

position along the bedway.

AE. Tailstock Clamp Bolt: Adjusts the clamping

pressure applied by the tailstock lock lever.

AF. Offset Scale: Indicates the relative distance

of tailstock offset from the spindle centerline.

AG Offset Lock Bolt: Clamps together the upper

and lower halves of the tailstock after the

offset is adjusted.

AH. Tailstock Stop Pin: Prevents the tailstock

from sliding off of the ways.

Figure 8. Tailstock controls.

AE

AF

AG

AH

-8-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

Safety Foot Brake

This lathe is equipped with a foot brake (see

Figure 9) to quickly stop the spindle instead of

allowing it to coast to a stop on its own.

Pressing the foot brake disengages the spindle

clutch from the motor drive train inside the

headstock.

After the foot brake is used, the spindle lever is

used to re-start spindle rotation.

Figure 9. Foot brake and spindle levers.

Foot Brake

Spindle Levers

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-9-

INTRODUCTION

Model Number SB1046PF SB1047PF SB1048PF

Product Dimensions

Weight 5830 lbs. 6600 lbs. 8140 lbs.

Width (side-to-side)/Depth

(front-to-back)/Height

110

1

⁄2" x 27" x 54

3

⁄4" 130

1

⁄4" x 27" x 54

3

⁄4" 169

3

⁄4" x 27" x 54

3

⁄4"

Foot Print (Width/Depth) 122

1

⁄4" x 71

3

⁄4" 141

3

⁄4" x 71

3

⁄4" 182" x 71

3

⁄4"

Shipping Dimensions

Type Wood Slat Crate

Weight 6182 lbs. 7040 lbs. 8712 lbs.

Width (side-to-side)/Depth

(front-to-back)/Height

121" x 45" x 69" 141" x 45" x 69" 183" x 45" x 69"

Electrical

Power Requirement 440V, 3-Phase, 60Hz

Full-Load Current Rating 19.23A

Minimum Circuit Size 30A

Switch Magnetic with Thermal Protection

Switch Voltage 440V

Plug Included No

Recommended Connection Type Hardwire to Locking Disconnect Switch

MODEL SB1046PF, SB1047PF, SB1048PF

21" TURN-NADO

®

GEARHEAD LATHE w/DRO

P.O. Box 2027, Bellingham, WA 98227 U.S.A.

PHONE: (360) 734-1540 • © South Bend Lathe Co.

www.southbendlathe.com

Product Speciﬁcations

-10-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

Model Number SB1046PF SB1047PF SB1048PF

Main Motor

Type TEFC Induction

Horsepower 15 HP

Voltage 440V

Phase 3-Phase

Amps 19A

Speed 1720 RPM

Cycle 60 Hz

Power Transfer V-Belt & Gear

Bearings Shielded & Permanently Sealed

Coolant Motor

Type TEFC Induction

Horsepower

1

⁄8 HP

Voltage 440V

Phase 3-Phase

Amps 0.23A

Speed 3450 RPM

Cycle 60 Hz

Power Transfer Direct Drive

Bearings Shielded & Permanently Sealed

Operation Information

Swing Over Bed 21 in.

Distance Between Centers 60 in. 80 in. 120 in.

Swing Over Cross Slide 14.01 in.

Swing Over Saddle 21 in.

Swing Over Gap 31.10 in.

Maximum Tool Bit Size 1 in.

Compound Travel 5.39 in.

Carriage Travel 59 in. 79 in. 119 in.

Cross Slide Travel 11 in.

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-11-

INTRODUCTION

Model Number SB1046PF SB1047PF SB1048PF

Headstock Information

Spindle Bore 3.15 in.

Spindle Taper MT#7

Number of Spindle Speeds 16

Range of Spindle Speeds 20–1600 RPM

Spindle Type D1-8 Camlock

Spindle Bearings Tapered Roller

Tailstock Information

Tailstock Quill Travel 6.5 in.

Tailstock Taper MT#5

Tailstock Barrel Diameter 3 in.

Threading Information

Number of Longitudinal Feeds 15

Range of Longitudinal Feeds 0.0015–0.0400 in./rev.

Number of Cross Feeds 15

Range of Cross Feeds 0.00075–0.0200 in./rev

Number of Inch Threads 38

Range of Inch Threads 2–72 TPI

Number of Metric Threads 40

Range of Metric Threads 0.4–14 mm

Number of Modular Pitches 18

Range of Modular Pitches 0.3–3.5 MP

Number of Diametral Pitches 21

Range of Diametral Pitches 8–44 DP

Dimensions

Bed Width 13.58 in.

Leadscrew Diameter 1

3

⁄8 in.

Leadscrew TPI 4 TPI

Leadscrew Length 85.39 in. 105.08 in. 145.43 in.

Steady Rest Capacity

5

⁄8–7

1

⁄16 in.

Follow Rest Capacity

5

⁄8–5

1

⁄8 in.

Faceplate Size 14 in.

Floor to Center Height 46.65 in.

Height With Leveling Jacks 47.9 in.

-12-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

Model Number SB1046PF SB1047PF SB1048PF

Construction

Headstock Cast Iron

Headstock Gears Flame-Hardened Steel

Bed Meehanite Castings with Induction-Hardened Ways

Stand Cast Iron

Paint Urethane

Other

Country of Origin Taiwan (Some Components Made in USA & Germany)

Warranty 1 Year

Serial Number Location ID Label on Front of Headstock

Assembly Time Approximately 1 Hour

Sound Rating at Idle 76 dB

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-13-

INTRODUCTION

Model Number SB1056F SB1057F SB1058F

Product Dimensions

Weight 4400 lbs. 5170 lbs. 5940 lbs.

Width (side-to-side)/Depth

(front-to-back)/Height

90

3

⁄4" x 27" x 54

3

⁄4" 110

1

⁄2" x 27" x 54

3

⁄4" 130

1

⁄4" x 27" x 54

3

⁄4"

Foot Print (Width/Depth) 102

1

⁄2" x 71

3

⁄4" 122

1

⁄4" x 71

3

⁄4" 141

3

⁄4" x 71

3

⁄4"

Shipping Dimensions

Type Wood Slat Crate

Weight 4708 lbs. 5522 lbs. 6380 lbs.

Width (side-to-side)/Depth

(front-to-back)/Height

100" x 45" x 69" 121" x 45" x 69" 141" x 45" x 69"

Electrical

Power Requirement 440V, 3-Phase, 60Hz

Full-Load Current Rating 19.23A

Minimum Circuit Size 30A

Switch Magnetic with Thermal Protection

Switch Voltage 440V

Plug Included No

Recommended Connection Type Hardwire to Locking Disconnect Switch

MODEL SB1056F, SB1057F, SB1058F

18" TURN-NADO

®

GEARHEAD LATHE w/DRO

P.O. Box 2027, Bellingham, WA 98227 U.S.A.

PHONE: (360) 734-1540 • © South Bend Lathe Co.

www.southbendlathe.com

Product Speciﬁcations

-14-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

Model Number SB1056F SB1057F SB1058F

Main Motor

Type TEFC Induction

Horsepower 15 HP

Voltage 440V

Phase 3-Phase

Amps 19A

Speed 1720 RPM

Cycle 60 Hz

Power Transfer V-Belt & Gear

Bearings Shielded & Permanently Sealed

Coolant Motor

Type TEFC Induction

Horsepower

1

⁄8 HP

Voltage 440V

Phase 3-Phase

Amps 0.23A

Speed 3450 RPM

Cycle 60 Hz

Power Transfer Direct Drive

Bearings Shielded & Permanently Sealed

Operation Information

Swing Over Bed 18.11 in.

Distance Between Centers 40 in. 60 in. 80 in.

Swing Over Cross Slide 11.02 in

Swing Over Saddle 18 in.

Swing Over Gap 27.95 in.

Maximum Tool Bit Size 1 in.

Compound Travel 5.39 in.

Carriage Travel 39 in. 59 in. 79 in.

Cross Slide Travel 11 in.

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-15-

INTRODUCTION

Model Number SB1056F SB1057F SB1058F

Headstock Information

Spindle Bore 3.15 in.

Spindle Taper MT#7

Number of Spindle Speeds 16

Range of Spindle Speeds 20–1600 RPM

Spindle Type D1-8 Camlock

Spindle Bearings Tapered Roller

Tailstock Information

Tailstock Quill Travel 6.5 in.

Tailstock Taper MT#5

Tailstock Barrel Diameter 3 in.

Threading Information

Number of Longitudinal Feeds 15

Range of Longitudinal Feeds 0.0015–0.0400 in./rev.

Number of Cross Feeds 15

Range of Cross Feeds 0.00075–0.0200 in./rev

Number of Inch Threads 38

Range of Inch Threads 2–72 TPI

Number of Metric Threads 40

Range of Metric Threads 0.4–14 mm

Number of Modular Pitches 18

Range of Modular Pitches 0.3–3.5 MP

Number of Diametral Pitches 21

Range of Diametral Pitches 8–44 DP

Dimensions

Bed Width 13.58 in.

Leadscrew Diameter 1

3

⁄8 in.

Leadscrew TPI 4 TPI

Leadscrew Length 65.71 in. 85.39 in. 105.08 in.

Steady Rest Capacity

5

⁄8–7

1

⁄16 in.

Follow Rest Capacity

5

⁄8–5

1

⁄8 in.

Faceplate Size 14 in.

Feed Rod Diameter 0.93 in

Floor to Center Height 45.08 in.

Height With Leveling Jacks 46.25 in

-16 -

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

INTRODUCTION

Model Number SB1056F SB1057F SB1058F

Construction

Headstock Cast Iron

Headstock Gears Flame-Hardened Steel

Bed Meehanite Castings with Induction-Hardened Ways

Stand Cast Iron

Paint Urethane

Other

Country of Origin Taiwan (Some Components Made in USA & Germany)

Warranty 1 Year

Serial Number Location ID Label on Front of Headstock

Assembly Time Approximately 1 Hour

Sound Rating at Idle 76 dB

For Machines Mfg. Since 3/11 Turn-Nado

®

Gearhead Lathes

-17-

SAFETY

Understanding Risks of Machinery

Operating all machinery and machining equipment can be dangerous or relatively safe depending

on how it is installed and maintained, and the operator's experience, common sense, risk awareness,

working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).

The owner of this machinery or equipment is ultimately responsible for its safe use. This

responsibility includes proper installation in a safe environment, personnel training and usage

authorization, regular inspection and maintenance, manual availability and comprehension,

application of safety devices, integrity of cutting tools or accessories, and the usage of approved

personal protective equipment by all operators and bystanders.

The manufacturer of this machinery or equipment will not be held liable for injury or property

damage from negligence, improper training, machine modiﬁcations, or misuse. Failure to read,

understand, and follow the manual and safety labels may result in serious personal injury, including

amputation, broken bones, electrocution, or death.

The signals used in this manual to identify hazard levels are deﬁned as follows:

Death or catastrophic

harm WILL occur.

Moderate injury or ﬁre

MAY occur.

Death or catastrophic

harm COULD occur.

Machine or property

damage may occur.

Basic Machine Safety

Owner’s Manual: All machinery and machining

equipment presents serious injury hazards

to untrained users. To reduce the risk of

injury, anyone who uses THIS item MUST

read and understand this entire manual

before starting.

Personal Protective Equipment:

Operating or

servicing this item may expose the user

to ﬂying debris, dust, smoke, dangerous

chemicals, or loud noises. These hazards

can result in eye injury, blindness, long-

term respiratory damage, poisoning,

cancer, reproductive harm or hearing loss.

Reduce your risks from these hazards

by wearing approved eye protection,

respirator, gloves, or hearing protection.

Trained/Supervised Operators Only: Untrained

users can seriously injure themselves

or bystanders. Only allow trained and

properly supervised personnel to operate

this item. Make sure safe operation

instructions are clearly understood. If

electrically powered, use padlocks and

master switches, and remove start switch

keys to prevent unauthorized use or

accidental starting.

Guards/Covers:

Accidental contact with

moving parts during operation may cause

severe entanglement, impact, cutting,

or crushing injuries. Reduce this risk by

keeping any included guards/covers/doors

installed, fully functional, and positioned

for maximum protection.

-18-

For Machines Mfg. Since 3/11

Turn-Nado

®

Gearhead Lathes

SAFETY

Entanglement: Loose clothing, gloves, neckties,

jewelry or long hair may get caught in

moving parts, causing entanglement,

amputation, crushing, or strangulation.

Reduce this risk by removing/securing

these items so they cannot contact moving

parts.

Mental Alertness: Operating this item with

reduced mental alertness increases the

risk of accidental injury. Do not let a

temporary influence or distraction lead to a

permanent disability! Never operate when

under the influence of drugs/alcohol, when

tired, or otherwise distracted.

Safe Environment:

Operating electrically

powered equipment in a wet environment

may result in electrocution; operating near

highly ﬂammable materials may result in a

ﬁre or explosion. Only operate this item in

a dry location that is free from ﬂammable

materials.

Electrical Connection: With electically powered

equipment, improper connections to the

power source may result in electrocution

or fire. Always adhere to all electrical

requirements and applicable codes when

connecting to the power source. Have all

work inspected by a qualified electrician to

minimize risk.

Disconnect Power: Adjusting or servicing

electrically powered equipment while it

is connected to the power source greatly

increases the risk of injury from accidental

startup. Always disconnect power

BEFORE any service or adjustments,

including changing blades or other tooling.

Secure Workpiece/Tooling:

Loose workpieces,

cutting tools, or rotating spindles can

become dangerous projectiles if not

secured or if they hit another object during

operation. Reduce the risk of this hazard

by verifying that all fastening devices are

properly secured and items attached to

spindles have enough clearance to safely

rotate.

Chuck Keys or Adjusting Tools:

Tools used to

adjust spindles, chucks, or any moving/

rotating parts will become dangerous

projectiles if left in place when the machine

is started. Reduce this risk by developing

the habit of always removing these tools

immediately after using them.

Work Area:

Clutter and dark shadows increase

the risks of accidental injury. Only operate

this item in a clean, non-glaring, and well-

lighted work area.

Properly Functioning Equipment:

Poorly

maintained, damaged, or malfunctioning

equipment has higher risks of causing

serious personal injury compared to

those that are properly maintained.

To reduce this risk, always maintain

this item to the highest standards and

promptly repair/service a damaged or

malfunctioning component. Always follow

the maintenance instructions included in

this documentation.

Unattended Operation:

Electrically powered

equipment that is left unattended while

running cannot be controlled and is

dangerous to bystanders. Always turn the

power OFF before walking away.

Health Hazards: Certain cutting fluids and

lubricants, or dust/smoke created when

cutting, may contain chemicals known to

the State of California to cause cancer,

respiratory problems, birth defects,

or other reproductive harm. Minimize

exposure to these chemicals by wearing

approved personal protective equipment

and operating in a well ventilated area.

Difﬁcult Operations:

Attempting difficult

operations with which you are unfamiliar

increases the risk of injury. If you

experience difficulties performing the

intended operation, STOP! Seek an

alternative method to accomplish the

same task, ask a qualified expert how the

operation should be performed, or contact

our Technical Support for assistance.

Page is loading ...

Grizzly SB1056F Owner's manual

Grizzly SB1056F Owner's manual

Related papers

Other documents