Miller KB111430 Owner's manual

Brand: Miller

Model: KB111430

Type: Owner's manual

This manual is also suitable for

EDT-2400-2

Miller KB111430 is a trailer with a gross vehicle weight rating of 2400 lbs., and a payload capacity of 2100 lbs. As it features a tongue weight of around 10%, it is compatible with various Miller engine-driven welding generators. The trailer comes with leaf springs and a heavy-duty axle to ensure safe and stable transportation. It can be equipped with optional fenders, taillights, and a ball hitch for road use, or a clevis or lunette eye hitch for off-road use. Note that additional accessories or equipment may alter the trailer's tongue weight.

July 1992 FORM: OM-664B

Effective With Serial No. KB111430

MODEL: EDT-2400-2

OWNER’S MANUAL

MILLER ELECTRIC Mfg. Co.

A Miller Group Ltd., Company

P.O. Box 1079

Appleton, WI 54912 USA

Tel. 414-734-9821

IMPORTANT: Read and understand the entire contents of both this manual

and the power source manual used with this unit, with special emphasis on

the safety material throughout both manuals, before installing, operating, or

maintaining this equipment. This unit and these instructions are for use only

by persons trained and experienced in the safe operation of welding equip-

ment. Do not allow untrained persons to install, operate, or maintain this unit.

Contact your distributor if you do not fully understand these instructions.

ST-149 848 PRINTED IN U.S.A

OM-664B - 7/92

TABLE OF CONTENTS

Section No. Page No.

SECTION 1 − SAFETY

1-1. General 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Weight 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Tongue Weight 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. Hitches 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Locking Device − Ball Hitch Option Only 1. . . . . . . . . . . . . . . . . . . . . . . .

1-6. Safety Chains 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-7. Breakaway Brake Chain 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-8. Lights 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-9. Tires 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-10. Wheel Nuts 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 − SAFETY PRECAUTIONS AND SIGNAL WORDS

2-1. General Information And Safety 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-2. Safety Alert Symbol And Signal Words 3. . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 − SPECIFICATIONS

3-1. Description 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 − INSTALLATION

4-1. Installing Wheels 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Installing Fenders (Optional) 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-3. Connecting Trailer Lights (Optional) 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-4. Installing Trailer To Towing Vehicle 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-5. Installing Welding Generator 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 − OPERATION AND MAINTENANCE

5-1. Trailer-Supporting Jack 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. General Maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 − PARTS LIST

Figure 6-1. Complete Assembly 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LIST OF CHARTS AND TABLES

Table 1-1. Maximum Recommended Tongue Weights By

Trailer Classification For Trailer Design* 1. . . . . . . . . . . . . . . . . . .

Table 3-1. Specifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4-1. Welding Generator Base Mounting Holes

For 10% Tongue Load 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OM-664 Page 3

SECTION 2 − SAFETY PRECAUTIONS AND SIGNAL WORDS

2-1. GENERAL INFORMATION AND SAFETY

A. General

Information presented in this manual and on various la-

bels, tags, and plates on the unit pertains to equipment

design, installation, operation, maintenance, and

troubleshooting which should be read, understood, and

followed for the safe and effective use of this equipment.

B. Safety

The installation, operation, maintenance, and trouble-

shooting of trailers requires practices and procedures

which ensure personal safety and the safety of others.

Therefore, this equipment is to be installed, operated,

and maintained only by qualified persons in accordance

with this manual and all applicable trailer safety stan-

dards.

2-2. SAFETY ALERT SYMBOL AND SIGNAL

WORDS

The following safety alert symbol and signal words are

used throughout this manual to call attention to and

identify different levels of hazard and special instruc-

tions.

This safety alert symbol is used with the signal

words WARNING and CAUTION to call atten-

tion to the safety statements.

WARNING statements identify procedures or

practices which must be followed to avoid seri-

ous personal injury or loss of life.

CAUTION statements identify procedures or

practices which must be followed to avoid minor

personal injury or damage to this equipment.

IMPORTANT statements identify special instructions

necessary for the most efficient operation of this equip-

ment.

SECTION 3 − SPECIFICATIONS

Table 3-1. Specifications

Gross Axle

Weight Rating

200 lbs.

(900 kg.)

Gross Vehicle

Weight Rating

2400 lbs.

(1080 kg.)

Net

Pay Load

2100 lbs.

(945 kg.)

Track (center to

center of tires)

53-1/2 in.

(1359 mm)

Road

Clearance

9 in.

(229 mm)

Height

Of Bed

21 in.

(533 mm)

Standard

Tires

F78-14

Shipping

Weight

280 lbs.

(127 kg.)

OM-664 Page 4

ST-149 848

**108-1/2 in.

(2756 mm)

*63-1/4 in.

(1607 mm)

40-3/8 in.

(1026 mm)

21 in.

(533 mm)

9 in.

(229 mm)

*62 in. (1575 mm)

without optional fenders

**102-1/2 in. (2604 mm)

without optional hitch

Figure 3-1. Dimensional View

OM-664 Page 5

3-1. DESCRIPTION

The EDT-2400-2 trailer is a two-wheel trailer with leaf

springs and heavy duty axle. It is designed to provide the

recommended trailer tongue weight with all MILLER en-

gine-driven Welding Generators listed in Table 4-1.

The EDT-2400-2 can be fitted with optional fenders, tail-

lights and ball hitch for over the road use. An optional

clevis or lunette eye hitch is available for off road use.

This trailer is not designed to mount welding accesso-

ries, tool boxes, etc. because the additional weight

would change the trailer tongue weight.

SECTION 4 − INSTALLATION

♦ Clevis

ST-149 846-A

Ground Lead

Wheel

Axle Assembly

Torque To

60 ft-lbs

(81 N·m)

♦ OPTIONAL

♦ Taillight

♦ Fender

♦ Taillight

♦ Fender

♦ Ball Hitch

RIGHT

Eye

♦ Lunette

Torque To

75 ft-lbs

(102 N·m)

REAR

LEFT

Torque To

20 ft-lbs

(27 N·m)

Taillight

Mounting

Bracket

Light

Reflector

Star

Washer

Trailer

Tongue

Torque To 75 ft-lbs

(102 N·m)

FRONT

Hitch

♦ Safety Pin

Figure 4-1. Trailer Assembly

IMPORTANT: The word FRONT, when used with refer-

ence to the trailer, means the tongue/hitch end of the

trailer. The words LEFT and RIGHT are with respect to

the operator standing at the rear of the trailer and facing

the towing vehicle.

IMPORTANT: Place engine end of generator toward

hitch end (front) of trailer.

4-1. INSTALLING WHEELS (Figure 4-1)

1. Read WARNING block at beginning of Section

4-4, and use jack to support trailer as instructed in

Section 5-1.

2. Install and secure shackle arms onto the end of

each spring on axle assembly using the 9/16 in.

hardware. Be sure not to compress ends of

brackets.

2. Install axle assembly to spring brackets on trailer

frame shackle arms using 9/16 in. hardware. The

securing hardware should be run up tight against

the spring brackets without compressing the

ends of the brackets.

3. Install the wheels on the hubs using the wheel

nuts on the hub. Tighten wheel nuts to 60 ft-lbs

(81 N·m).

OM-664 Page 6

4-2. INSTALLING FENDERS (Optional) (Figure

4-1)

1. Read WARNING block at beginning of Section

4-4, and use jack to support trailer as instructed in

Section 5-1.

2. Install and secure fenders onto trailer frame us-

ing supplied 3/8-16 x 1-1/4 in. hex-head cap

screws and associated hardware (see Figure

4-1). Tighten hardware to approximately 20 ft-lbs

(27 N·m).

4-3. CONNECTING TRAILER LIGHTS (Optional)

(Figures 4-2 And 4-3)

A. Lead Connections To Trailer Lights

CAUTION: INCORRECT WIRING PROCE-

DURE can cause electric shock and equip-

ment damage.

• Disconnect vehicle wiring harness plug from

trailer wiring connector, if applicable.

• Use tab connector only with insulated wires.

• Do not strip insulation.

• Use only recommended tool: 9 in. (229 mm)

lineman’s pliers.

1. Read WARNING block at beginning of Section

4-4, and use jack to support trailer as instructed in

Section 5-1.

2. Locate wiring harness in shipping box.

3. Splice the supplied lead containing a ring terminal

to white ground lead extending from plug of wiring

harness. Splice leads together using supplied tab

connector (see Figure 4-2).

4. Install and secure ring terminal on lead to tongue

plate using 1/4-20 hardware.

5. Install right taillight as follows:

a. Route brown and green leads from wiring har-

ness through steel clamps on inside, right side

of trailer frame channel, and out end of channel.

b. Slip a 12 in. (305 mm) piece of sleeving over the

leads, and route leads through back of right tail-

light mounting bracket.

c. Insert stripped end of brown lead fully into the

TAIL hole in rear of taillight, and insert stripped

end of green lead fully into STOP hole in rear of

taillight.

IMPORTANT: When leads are installed, they are auto-

matically secured to the lights.

d. Install taillight onto right taillight mounting

bracket with TOP of light up. Secure taillight us-

ing 1/4 in. hardware.

e. Route stripped end of either short lead

(supplied) through access hole in right trailer

frame channel, and insert it fully into top MARK-

ER BROWN hole in rear of side light/reflector.

f. Splice remaining end of short lead to brown lead

from wiring harness using supplied tab connec-

tor (see Figure 4-2).

g. Install and secure right side light/reflector onto

trailer frame, placing a star washer between the

frame and light/reflector (see Figure 4-1). Se-

cure light/reflector with supplied No. 10 hard-

ware.

6. Install left taillight as follows:

a. Route brown and yellow leads from wiring har-

ness through steel clamps on inside, left side of

trailer frame channel, and out end of channel.

b. Slip a 12 in. (305 mm) piece of sleeving over the

leads, and route leads through back of left tail-

light mounting bracket.

c. Insert stripped end of brown lead fully into the

TAIL hole in rear of taillight, and insert stripped

end of yellow lead fully into STOP hole in rear of

taillight.

d. Install taillight onto left taillight mounting brack-

et with TOP of light up. Secure taillight using 1/4

in. hardware.

e. Route stripped end of remaining short lead

(supplied) through access hole in left trailer

frame channel, and insert it fully into top MARK-

ER BROWN hole in rear of side light/reflector.

f. Splice remaining end of short lead to brown lead

from wiring harness using supplied tab connec-

tor (see Figure 4-2).

g. Install and secure left side light/reflector onto

trailer frame, placing a star washer between the

frame and light/reflector (see Figure 4-1). Se-

cure light/reflector with supplied No. 10 hard-

ware.

S-0448

Step 1. Place unstripped run wire inside run channel.

Step 2. Insert unstripped tap wire into connector until

it hits stop inside connector.

Step 3. Make connection with pliers by driving con-

tact down flush with top of connector.

Step 4. Close hinged top cover until latched.

Step 1. Step 2. Step 3. Step 4.

Tap Wire

Run Wire

Contact

9 in. (229 mm)

Lineman’s Pliers

Figure 4-2. Lead Installation Into Tab Connector

OM-664 Page 7

SB-000 297-E

Fender

Lamp

Units

LEFT

RIGHT

Yellow Brown

LeadLead

Clearance

Lamps

Brown Green

LeadLead

Short

Leads

To Trailer To Vehicle

Ground Lead

(Ground To

Trailer Frame)

Tab Connector

White (Ground) Lead

Ground

(White)

Taillights

(Brown)

Left Stop/

Signal Lamps

(Yellow)

Right Stop/

Signal Lamps

(Green)

Figure 4-3. Lead Connections To Towing Vehicle

B. Lead Connections From Trailer Wiring Harness

To Towing Vehicle (Figure 4-3)

Connect leads from trailer wiring harness to the towing

vehicle according to the following color code:

GREEN - Connect to towing vehicle right stop/signal

light.

YELLOW - Connect to towing vehicle left stop/signal

light.

BROWN - Connect to towing vehicle taillights.

WHITE - Connect to towing vehicle chassis

(ground).

4-4. INSTALLING TRAILER TO TOWING VE-

HICLE (Figure 4-1)

WARNING: FALLING EQUIPMENT can

cause serious personal injury and equip-

ment damage.

• Use equipment of adequate capacity to lift the

unit.

• Use adequate blocks or lifting device to sup-

port hitch end while pivoting trailer jack into

position (see Section 5-1).

• Use trailer jack to obtain desired height and to

support tongue weight while installing hitch.

A. Ball Hitch (Optional)

1. Use jack to support trailer as instructed in Section

5-1.

2. Use holes in side of trailer tongue to install and

secure 2 in. (51 mm) ball hitch to top of trailer

tongue with 1/2-13 x 3-1/2 in. hardware. Tighten

hardware to 75 ft-lbs (102 N·m).

3. Set trailer hitch onto ball and push lever down. In-

sert safety pin through hole in lever to secure the

hitch. (To remove trailer, remove safety pin and

release lever).

4. Cross safety chains one over the other, and at-

tach safety chains to towing vehicle. Block trailer

wheels to prevent trailer from moving.

B. Clevis Eye Hitch (Optional)

1. Use jack to support trailer as instructed in Section

5-1.

2. Install one clevis bar to top of trailer tongue and

other clevis bar to bottom of trailer tongue using

1/2-13 x 4 1/2 in. hardware. Tighten hardware to

75 ft-lbs (102 N·m).

3. Attach and secure trailer hitch to towing vehicle.

4. Cross safety chains one over the other, and at-

tach safety chains to towing vehicle. Block trailer

wheels to prevent trailer from moving.

C. Lunette Eye Hitch (Optional)

1. Use jack to support trailer as instructed in Section

5-1.

2. Install and secure lunette eye hitch to top of trailer

tongue using 1/2-13 x 3-1/2 in. hardware. Tighten

hardware to 75 ft-lbs (102 N·m).

3. Install and secure trailer hitch onto towing ve-

hicle.

4. Cross safety chains one over the other, and at-

tach safety chains to towing vehicle. Block trailer

wheels to prevent trailer from moving.

OM-664 Page 8

4-5. INSTALLING WELDING GENERATOR

CAUTION: UNCONTROLLED TILTING OF

TRAILER can result in personal injury or

equipment damage.

• Use equipment of adequate capacity to lift the

unit.

• Install welding generator onto trailer with en-

gine end toward hitch end of trailer.

• Distribute weight so that trailer tongue weight

is approximately 10% of the gross trailer

weight.

1. Use jack to support trailer as instructed in Section

5-1.

2. Align mounting holes in welding generator with

proper holes in trailer frame. See Table 4-1.

When using the trailer with welding generators

not listed in Table 4-1, distribute weight so trailer

tongue weight is approximately 10% of the gross

trailer weight.

3. Secure generator to frame with 3/8 in. grade 5

hardware, and tighten hardware to 30 ft-lbs (41

N·m).

Table 4-1. Welding Generator Base Mounting Holes For 10% Tongue Load

Model

All Big 20 & Big 40 Models

Big Blue 250D

Big Blue 400D

Trailblazer 44 & 55D+

Trailblazer 44 & 55G+

(Dimensional from generator end)

8-1/4 in. (209.6 mm) & 45 in. (1143.0 mm)

7-5/8 in. (193.7 mm) & 44-3/8 in. (1127.1 mm)

10-1/2 in (266.7 mm) & 47-1/4 in. (1200.2 mm)

17 in. (431.8 mm) & 53-3/4 in (1365.3 mm)

15 in. (381.0 mm) & 51-3/4 in. (1314.5 mm)

Welding Generator Base Mounting Holes

+All Trailblazer models use the same base rails. Be sure to install the D

and G models using the correct mounting holes.

SECTION 5 − OPERATION AND MAINTENANCE

5-1. TRAILER-SUPPORTING JACK

The trailer-supporting jack, located on the front, left cor-

ner of the trailer chassis, supports the trailer in a hori-

zontal position in the absence of a towing vehicle. To use

the trailer-supporting jack, lower the jack to its vertical

position as follows:

1. Pull the spring-loaded jack securing pin until the

jack is free to pivot.

2. Pivot the jack down the the vertical position. The

jack securing pin should lock the jack in a vertical

position.

IMPORTANT: Rotating the jack handle clockwise will

raise the trailer tongue. Rotating the handle counter-

clockwise will lower the trailer tongue.

3. When not in use, return the jack to its horizontal

position by pulling the jack securing pin until the

jack is free to pivot.

IMPORTANT: Whenever performing any maintenance,

lubrication, or adjustment, watch for any indication of

excessive wear, damage or malfunction. Check for free

rotation of assemblies mounted on bushings or bear-

ings. Do not operate the trailer if any component is dam-

aged or malfunctioning.

5-2. GENERAL MAINTENANCE

A. General

Lubricate all moving parts on the trailer at least once

each year using SAE 20WQ oil. If trailer is exposed to

elements or frequent off-the-road use, lubricate trailer

parts more often.

B. Wheel Bearings

Check wheel bearing every 12,000 miles, and repack

bearings if necessary. Bearings should be repacked

with a good quality lithium-based extreme pressure

grease.

OM-664 Page 9

SECTION 6 − PARTS LIST

37 36

35 34

32 31 30

2324252627

21 20

145

678

ST-149 847-A

Figure 6-1. Complete Assembly

OM-664 Page 10

Description Quantity

Part

No.

Figure 6-1. Complete Assembly

Item

No.

1 087 937 FENDER, RH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 034 136 LAMP, 12V (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 034 137 LAMP, 12V w/license light (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 601 865 NUT, stl hex full fnsh .250-20 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 602 207 WASHER, lock stl split .250 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 601 966 SCREW, cap stl hexhd .375-16 x 1.250 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 602 213 WASHER, lock stl split .375 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 601 872 NUT, stl hex full fnsh .375-16 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 087 938 FENDER, LH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 127 672 LOCK NUT 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 127 671 SHACKLE ARMS 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 088 873 SPRING BOLTS 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 088 874 HUB ASSEMBLY, w/bearings (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 088 877 SEAL, grease 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 088 875 INNER CONE & ROLLER ASSEMBLY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 088 876 OUTER CONE & ROLLER ASSEMBLY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 088 878 CAP, grease 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 088 879 WHEEL NUT, .500-20 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 110 876 WHEEL, w/tire F78-14 & white spoke rim (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 110 803 RIM, 14.000 in x 5.500 wide 5 hole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 022 675 TIRE, tubeless F78-14 4 ply 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 088 862 AXLE ASSEMBLY, (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 088 866 NUT, spindle 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 088 867 COTTER PIN 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 088 868 SPINDLE WASHER 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 088 865 SPRING PLATE 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 088 863 U-BOLTS, .500-13 x 5.625 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

088 864 NUT, U-bolt .500-13 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 088 869 SPRING, leaf (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29 088 870 NYLON BUSHING 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 010 423 CONNECTOR, tab 14-18 wire 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31 602 110 SCREW, mach stl rdh 10-24 x .750 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

602 203 WASHER, lock stl split No. 10 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

601 861 NUT, stl hex mscr 10-24 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32 034 479 LIGHT & REFLECTOR, amber 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33 087 936 FRAME, trailer (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34 087 638 JACK, swivel 2000/5000 lb 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35 130 227 CHAIN, safety 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36 601 978 SCREW, cap stl hexhd .500-13 x 3.500 (coupler hitch & lunette eye) 2. . . . . . . . . . . . . . . . . . . . .

36 149 638 SCREW, cap stl hexhd .500-13 x 4.500 (clevis hitch) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37 602 246 WASHER, flat stl std .500 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38 150 393 PIN, lynch .312dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39 087 639 COUPLER, hitch 2 in ball 3500 lb cap 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 088 058 NUT, stl slflkg hex light .500-13 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

41 087 949 BAR, hitch clevis 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42 605 710 CONNECTOR, trailer lights 4 prong 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43 605 709 HARNESS, wiring 15ft 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

605 569 TUBING, gl acrylic .289-.311 ID No. 2 (order by ft) 2ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44 601 954 SCREW, cap stl hexhd .250-20 x .750 (ground) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

602 208 WASHER, lock stl ext tooth .250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

602 240 WASHER, flat stl std .250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

602 207 WASHER, lock stl split .250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

601 865 NUT, stl hex full fnsh .250-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45 087 952 LUNETTE EYE, 2.625 ID 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

605 783 SCREW, cap stl hexhd .625-18 x 2.000 (mtg generator) 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

034 121 WASHER, beveled .625 hole 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

601 851 NUT, stl slflkg hex reg .625-18 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.