FMI C21TO Operating instructions

FMI
Brand
FMI
Model
C21TO
Type
Operating instructions

This manual is also suitable for

FMI C21TO is a corner mantel and base assembly designed for use with FMI 21'' or 23'' electric and gas fireplace systems. The mantel is constructed from durable materials and features a classic design that will complement any décor. The base assembly provides a sturdy foundation for the mantel and fireplace, and the included trim strips help to conceal any gaps between the mantel and the wall. The FMI C21TO is easy to assemble and install, and it comes with all the necessary hardware and instructions.

FMI C21TO is a corner mantel and base assembly designed for use with FMI 21'' or 23'' electric and gas fireplace systems. The mantel is constructed from durable materials and features a classic design that will complement any décor. The base assembly provides a sturdy foundation for the mantel and fireplace, and the included trim strips help to conceal any gaps between the mantel and the wall. The FMI C21TO is easy to assemble and install, and it comes with all the necessary hardware and instructions.

For more information, visit www.fmiproducts.com
C21TP and C21TO
Corner Mantel and Base
ASSEMBLY AND INSTALLATION INSTRUCTIONS
IMPORTANT: Read entire instruction sheet be-
fore assembling or installing mantel kit.
These mantels are only approved for use with
any FMI PRODUCTS, LLC 21'' or 23'' electric and
gas replace systems. Do not use mantel with
any other product.
This mantel kit contains the following:
• Mantel pieces - unassembled and numbered as follows:
#1 Base
#2 Right Side Assembly
#3 Left Side Assembly
#4 Header
#5 Top
#6 Base Support
#7 Vertical Support
Right Top Trim Strip
Left Top Trim Strip
• Hardware Package
22 - 1 1/4" Wood Screws 114325-01
8 - 1" Finishing Nails 114295-04
* Extra hardware may be included
Tools required:
• Power Screwdriver with #2 Phillips Bit
• Hammer
• Nail Set
If any wood pieces are missing or damaged, contact the dealer
where you purchased this mantel for replacement. If hardware
is missing or damaged, contact FMI PRODUCTS, LLC at
1-866-328-4537 for referral information. You can also visit
FMI PRODUCTS, LLC’s web site at www.fmiproducts.com.
Note: Gather all mantel pieces together before assembling
mantel.
WARNING: Only use 1¼" screws to assemble
mantel. Damage to mantel will result if other
screws are used for this purpose.
ASSEMBLING MANTEL
IMPORTANT: More than one person is required
to lift assembled mantel. Lift mantel by leg
assemblies. Lifting by header or mantel top
could damage mantel.
Use the following illustrations to assemble mantel. Use only
screws provided.
www.fmiproducts.com
123752-01B
2
Figure 1 - Installing Base Support
Figure 3 - Installing Mantel Base
Figure 4 - Installing Mantel Top
Figure 2 - Installing Header
1¼'' Screws
Base Support #6
Base #1
IMPORTANT: Align mantel left to right on base before installing.
Corner of mantel legs must be ush with back of mantel
base before installation (see Figure 5). Use a tape measure
to insure accuracy.
Header #4
Right Leg
Assembly #2
Left Leg
Assembly
#3
1¼'' Screws
Header
Assembly
Block
Left Leg
Assembly #3
Right Leg
Assembly #2
1¼'' Screws
Base #1
Mantel Top #5
Assembly
Blocks
Assembly
Blocks
Corner
of Mantel
Legs Must
be Flush
with edge
of Mantel
Top
Mantel Legs
Flush with
Mantel Base
1¼''
Screws
IMPORTANT: Align mantel top left to right before installing.
Backcornerofmantellegmustbeushwithedgeofmantel
top before installation.
www.fmiproducts.com
123752-01B
3
Figure 6 - Installing Fireplace into Mantel Assembly
IMPORTANT: Vertical support must be installed before re-
place is installed from front of mantel. Do not put any weight
on mantel top until vertical support has been installed.
Vertical Support Installation
Install vertical support (see Figure 5).
INSTALLING MANTEL WITH GAS FIREPLACE
1. Mantelmustbeinstalledushwithwall.Removebase-
board. Baseboard will prevent proper installation of man-
telandbase.Baseboardmustbealteredtotmantel.
2. Place hearth base against wall at installation location. Cut
anaccessholeinhearthbasetorungaslinetoreplace.
Make sure to locate access hole so cabinet mantel will
cover it when installed.
Note:Youcansecurebasetooorusingwoodscrews.
Countersink screw heads and putty over.
3. Route exible gas line through access hole in hearth
base.
4. Attach exible gas lineto replace gas regulator. See
Connecting to Gas Supply in owner’s manual.
5. Check all gas connections for leaks. See Checking Gas
Connectionsinreplaceowner’smanual.
6. Carefullyinsertreplaceintocabinetmantel(seeFigure
6).Usecautionwhenpositioningreplaceonbase.Base
may scratch easily.
Figure 5 - Installing Vertical Support
Base Support #6
Vertical
Support
#7
1¼'' Screws
1¼'' Screws
Top Center
Support
INSTALLING MANTEL WITH ELECTRIC
FIREPLACE
1. Mantelmustbeinstalledushwithwall.Removebase-
board. Baseboard will prevent proper installation of mantel
andbase.Baseboardmustbealteredtotmantel.
2. Place hearth base against wall at installation location.
3. Plugthepowercord,locatedintherearofthereplace,
into a 120 volt electric outlet.
4. Positionelectricreplaceinsidemantel(seeFigure7).
Usecautionwhen positioningreplaceonbase. Base
may scratch easily.
123752-01
Rev. B
09/11
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537
www.fmiproducts.com
Figure 8 - Installing Mantel Trim
Finishing Nails
Trim Strips
COMPLETING MANTEL INSTALLATION
1. Carefully push mantel and base into position in corner
andushagainstbothwalls.Checkoperationofreplace
before proceeding.
2. Place right trim strip on right side of top and left trim on left
side of top. Align both pieces so any gaps between mantel
and wall are covered as well as possible and front of trim
stripsareushwithsideoftop.Withonepersonholding
trimstripsinplace,naileachstriptomantleusingnishing
nails included in hardware kit and nail set.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

FMI C21TO Operating instructions

FMI
Brand
FMI
Model
C21TO
Type
Operating instructions
This manual is also suitable for

FMI C21TO is a corner mantel and base assembly designed for use with FMI 21'' or 23'' electric and gas fireplace systems. The mantel is constructed from durable materials and features a classic design that will complement any décor. The base assembly provides a sturdy foundation for the mantel and fireplace, and the included trim strips help to conceal any gaps between the mantel and the wall. The FMI C21TO is easy to assemble and install, and it comes with all the necessary hardware and instructions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents