Before you begin the installation, read all instructions.
Legal Warning
Certain uses of security camera
products and audio devices, such as
employee monitoring, surreptitious
viewing and recording of images and/or
audio, or the use, publication or
distribution of image and/or audio
recordings, are prohibited or restricted
by country, state and local laws.
Be sure to comply with the laws in your
country, state, and locality when using
Logitech Alert products and services.
1) Be sure that Logitech Alert Commander sotware is running on the PC
before beginning installation of camera.
• Shortly after connecting, your camera will appear in Alert Commander software. You can now move the camera to its desired location.
1 Logitech Outdoor Camera
2 Camera power supply
3 Power supply cable (yellow tips)
4 Mounting accessories
5 microSD™ card adapter
6 System Requirements Guide
Getting started with
Logitech
®
Alert
™
700e
Add-On Camera
!
Run Logitech Alert Commander
Logitech Alert Master System required.
!
1
2 3
4
5
6
2
Plug in Your Camera
When prompted to connect your camera:
1) Unscrew the hatch from the back of the camera and lift.
1a) Plug the yellow cable connector into the port.
1b) Screw the hatch firmly in place.
2) Unscrew the hatch from the power supply.
2a) Plug the yellow cable into the power supply port.
2b) Screw the hatch firmly in place.
2c) Mount the power supply unit to the wall.
2d) Plug the power connector into the plug slider and plug the power supply into an
outlet.
Wall/Ceiling Mounting Instructions
The wall mount allows you to easily fasten your camera to a wall, post,
overhang, or other surface.
1) Start by pre-drilling holes into the base surface and then fastening the
mouting base with the included screws.
2) Assemble the mounting arm and attach it to the base.
3) Attach the camera to the mounting arm.
1
1a 1b
2
2a
2b
2c
2d
1
2
3
or
!
RECOMMENDATION:
Mount the Outdoor Camera under an eave or
other overhang so that it is not exposed to direct
sunlight.
1
Power Supply Install Note
The power supply unit is weatherproof and can be installed outdoors. Use these tips to
ensure reliable power supply usage. Make sure the outdoor outlet is weatherproof. Do
NOT place on the ground.
1) Do NOT plug the power supply into a surge protector or power strip as they
interfere with the cameras. Surge protectors are built-in to the power supply and
protect the cameras.
2) Do NOT plug the power supply into the wall so that it lays horizontally or flat.
3) Do NOT mount the power supply upside down. Keep the cable connector port on
the bottom.
3
4
1
4) Avoid direct sunlight.
2
!
CAUTION: If left in sunlight, surface may be hot to the touch.
Quick-start
guide
Logitech
Alert
™
700e/750e
System Requirements
& Support Guide
© 2010 Logitech. All rights reserved. Logitech, the Logitech logo, and other Logitech marks are owned by Logitech and may be
registered. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors
that may appear in this manual. Information contained herein is subject to change without notice.
620-002016 rev005
www.logitech.com
FAQs
Where can I find more information?
Commander Help
You can press the F1 key from any screen in the Alert
Commander to access the online Help system.
Knowledge Base
Troubleshooting help is available at www.logitech.com/support
Customer Support
Call 1.888.469.4543
Refer to System Requirements Guide.
What do I do if I need a longer power supply cable?
Logitech CAT-5e cables have been specially designed to create a weatherproof
seal when attached to the camera and power supply. We do not recommend
using after market cables. Longer cables are available for purchase at
www.logitech.com/dvs/ (Accessories).
HELP
Motion LED
Reading the Diagnostic LEDs
Turning Off Motion and Diagnostic LEDs
You can turn off the motion and diagnostic LEDs in the
Settings > Camera dialog.
See F1 Help for instructions.
How do I know the camera is recording?
Which LED colors indicate “camera is working”?
Which LED colors indicate “camera is not working”?
Power Suppy
Diagnostic LEDs
What do these LEDs tell me?
Power Supply
Status LED
What do these LEDs tell me?
* See Camera Reset Instructions for assistance.
Want to see more FAQs?
Go to www.logitech.com/security/support
Camera Reset Instructions
Insert a paper clip into the reset hole located on the back of the camera and
press gently and then release.
If the camera does not appear after reset, go to Settings > Cameras >
Add/Find > Find Cameras. If the camera still does not operate, contact
technical support.
Resetting the camera will not delete video recorded on the microSD card.
Camera boot-up failed * (Red blinking)
microSD card read/write failure - No microSD
card * (Alternating Red / Yellow, blinking)
Camera is ready to record (Red)
Camera is recording (Red, blinking)
Connected to Internet (Green)
Connected to Alert Commander (Purple)
Connected to Alert Commander & Internet (Blue)
Upgrading Firmware (White)
Camera in standalone mode (Yellow)
Not connected to Alert Commander or Internet (Light Blue)
Traffic and data is flowing (Green)
Connection with Ethernet/LAN
(Yellow)
Link to Power Supply (Green)
Shows network traffic (Blue)
MMC/SD
MS/MS PRO
COMPACT FLASH I/II
SMARTMEDIA
microSD Logo is a trademark of SD-3C, LLC.
Using the microSD™ card adapter
NOTE: Unplug the camera before removing, replacing, or upgrading your
microSD card.
microSD card comes pre-installed.
To review the video on the microSD card, we recommend you using
Logitech Alert Commander.
To review the video on the microSD card without Logitech Alert
Commander:
1) Open the hatch on the bottom of the camera and remove the microSD
card from its port.
2) Plug the microSD card into the adapter.
3) Plug the adapter into the PC’s SD card slot.
• View video recordings using the free Apple QuickTime player or other
player that supports H.264 video playback. (To download QuickTime, visit
http://www.apple.com/quicktime/download/)
!
microSD card must be installed in the camera for recording to
occur.
1 2
3
Troubleshooting camera connection:
What if camera/video disappears?
1) Test another outlet for your camera, perhaps one closer to your PC.
2) Verify that the camera power supply and the network bridge are plugged
directly into a power outlet and not a power strip.
3) Check firewall settings or press the F1 key in Commander Software for
additional help.
4) Go to Settings > Cameras > Add/Find > Find Cameras.
5) Reset the camera. See instructions in “Camera Reset Instructions.”
Camera Diagnostic LED
Camera Diagnostic LED
Quick-start
guide
Logitech
Alert
™
700e/750e
System Requirements
& Support Guide
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Logitech ALERT 750E User manual
-
-
-
-
-
Ultimate Ears 980-000910 User manual
-
-
-
-
Other documents
-
Christie DWU700-GS User manual
-
Fujitsu VFY:S3650MF011DE Datasheet
-
Acer 2900 User manual
-
-
Precision Power EEEPC1000BLK001X - Eee PC 1000 Netbook User manual
-
Asus Eee PC 900 Linux User manual
-
IBM DISA e-collaboration User manual
-
dji RoboMaster S1 User manual
-
Chamberlain 754E Owner's manual