Sunbeam Bedding MF2000 User manual

Brand: Sunbeam Bedding

Model: MF2000

Category: Thermostats

Type: User manual

This manual is also suitable for

MF1500

Micro Furnace

Ceramic Disc Heaters

Instruction Booklet

This book covers the use and care of the following Micro Furnace heaters:

MF2000 2000W Micro Furnace Ceramic Disc Heater

MF1500 1500W Micro Furnace Ceramic Disc Heater

Please read these instructions carefully

and retain for future reference.

Sunbeam’s Safety Precautions 1

Safety Precautions for your heater 2

Sunbeam’s Total Safety System 3

Features of your 2000W Micro Furnace 4

Features of your 1500W Micro Furnace 6

Using your heater 8

Care and cleaning 9

Contents

Sunbeam are very safety conscious when

designing and manufacturing consumer products,

but it is essential that the product user also

exercise care when using an electrical appliance.

Listed below are precautions which are essential

for the safe use of an electrical appliance:

• Read carefully and save all the instructions

provided with an appliance.

• Always turn the power off at the power outlet

before you insert or remove a plug. Remove

by grasping the plug - do not pull on the cord.

• Turn the power off and remove the plug

when the appliance is not in use and

before cleaning.

• Do not use your appliance with an extension

cord unless this cord has been checked

and tested by a qualified technician or

service person.

• Always use your appliance from a power

outlet of the voltage (A.C. only) marked

on the appliance.

• Close supervision is necessary when your

appliance is being used near children or

infirm persons.

• Never leave an appliance unattended while

in use.

• Young children should be supervised to ensure

that they do not play with the appliance.

• Do not use an appliance for any purpose

other than its intended use.

• Do not place an appliance on or near a hot gas

flame, electric element or on a heated oven.

Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang

over the edge of a table or bench top or touch

any hot surface.

• For safety reasons and to avoid maintenance

by unskilled persons, some appliances are

‘sealed’ using tamperproof screws. Such

appliances should always be returned to the

nearest Sunbeam Appointed Service Centre

for adjustment or repair if required.

• Do not operate any electrical appliance with a

damaged cord or after the appliance has been

dropped or damaged in any manner. If damage

is suspected, return the appliance to the

nearest Sunbeam Appointed Service Centre

for examination, repair or adjustment.

• For additional protection, Sunbeam

recommend the use of a residual current

device (RCD) with a tripping current not

exceeding 30mA in the electrical circuit

supplying power to your appliances.

• Do not immerse the appliance in water

or any other liquid unless recommended.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

• This heater becomes hot during use. To avoid

burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this

heater. Keep combustible materials such as

furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (90cm) away from the

front of the heater and keep them away from

the sides and rear.

• Extreme caution is necessary when any heater

is used by or near children or invalids and

whenever the heater is left unattended.

• Always unplug the heater when not in use.

• Do not use outdoors.

• Do not run the cord of the heater under

carpeting. Do not cover the cord with throw

rugs, runners or other floor coverings. Arrange

the cord away from traffic areas where it will

not be tripped over.

• Do not locate the heater immediately below a

socket outlet.

• Do not use this heater in the immediate

surrounds of a bath, shower, laundry area or

swimming pool.

• Do not insert or allow foreign objects to enter

any ventilation or exhaust openings as this may

cause electric shock or fire, or damage to the

heater.

• To prevent a possible fire, do not block air

intakes or exhaust in any manner. Do not use

on soft surfaces, such as beds, where opening

may become blocked.

• A heater has hot and arcing or sparing parts

inside. Do not use it in areas where petrol,

paint or flammable liquids are used or stored.

Important instructions – retain for

future use.

Safety auto shut off

Your Sunbeam Micro Furnace Heater is

equipped with a safety system that detects

any abnormally high temperatures within

the heater and automatically shuts it off to

prevent overheating. This first stage of the

safety system requires the user to manually

reset the heater for it to resume operation.

For instructions on how to reset your

heater, see page 6.

Thermal back-up fuse

In addition to this automatic cut off, your

heater contains a thermal back-up fuse to

provide additional back-up protection. If

the heater is in an overheat situation, the

back-up fuse will open, stopping the power

flow to the ceramic heating discs and fan.

This fuse cannot be reset, so in the event

that the back-up fuse is activated, the

heater will need to be replaced.

Sunbeam’s Total Safety System

Electronic thermostat

The electronic thermostat works with the

external temperature sensor to maintain your

selected temperature. It constantly monitors

the room’s temperature and continuously

varies the heat output to maintain your

desired comfort level.

Ceramic disc heating system

Each ceramic disc contains 1200 honeycomb

shaped holes that heat all of the air that

passes through them, generating up to 40%

more warmth than conventional coil or

ceramic chip heaters.

External temperature sensor

The temperature sensor is located at the rear

of the unit, not inside the heater itself, to

ensure accurate temperature measurement.

It detects even the slightest change in the

room’s temperature, and communicates

this to the electronic thermostat.

Tip over cut-out

Should your heater accidentally be

knocked over, the instant tip over cut will

automatically interrupt power to the heating

element and fan. The heater will not resume

operation until it is replaced in the upright

position.

Power/Mode light

The power light illuminates amber to indicate

that the heater is connected to the power

outlet and is set to AUTO mode. It

illuminates green when the heater is set to

MANUAL mode.

Features of your 2000W

Micro Furnace heater

Temperature light

The temperature light illuminates red once

the selected temperature level is reached.

Removable dust filter

The filter collects dirt and dust from the air

circulating through the heater. It is

removable for easy cleaning.

Mode/Standby button

Use the standby button to select the desired

operating mode. Pressing the standby button

once selects the AUTO mode, twice selects

the MANUAL mode, and pressing a third

time selects the STANDBY mode.

AUTO mode

Select AUTO mode for thermostatically

controlled operation.

MANUAL mode

Select MANUAL mode for constant heat

output at your desired heat level, from

setting 1 to 5.

LED screen

The LED screen displays the ambient room

temperature, and the selected setting during

adjustment.

+ and - buttons

Use the + and – buttons to adjust the

selected temperature when in AUTO mode,

or to select the desired heat setting when in

MANUAL mode.

Mode dial

Use the mode dial to select the desired operating

mode: FAN to circulate cool air; HEAT to operate the

heater, or OFF.

Thermostat dial

Use the thermostat dial to select the desired

temperature, from 10°C to 27°C. Once the selected

temperature level is reached, the thermostat will

contantly adjust the heat output to maintain it.

Tip over cut-out

Should your heater accidentally be knocked over, the

instant tip over cut will automatically interrupt power

to the heating element and fan. The heater will not

resume operation until it is replaced in the upright

position.

Electronic thermostat

The electronic thermostat constantly monitors the

room’s temperature and adjusts the heat output to

maintain your selected temperature.

Features of your 1500W

Micro Furnace heater

Power light

Illuminates to indicate that the heater is

connected to the power outlet and is

switched on.

Temp limit light

Illuminates to indicate that the room has

reached the selected temperature.

Removable dust filter

The filter collects dirt and dust from the air

circulating through the heater. It is

removable for easy cleaning.

Ceramic disc heating

Each ceramic disc contains 1200

honeycomb shaped holes that heat all of the

air that passes through them, generating up

to 40% more warmth than conventional coil

or ceramic chip heaters.

1. Place the heater on a flat level surface,

approximately 1 metre from any wall or

other objects such as furniture, curtains,

plants or combustible material, and ensure

that the air intake and outlet are clear of

obstructions.

Note: For most efficient heating, place the

heater on the floor where the air is cooler,

near an outside door, the bottom of a

staircase, or where colder air is most likely

to be entering the room.

2. Insert the plug into a 230-240V power

outlet and turn the power on. The red

power light will illuminate and the screen

will display the ambient room temperature.

3. Press the Standby button to select the

desired operating mode. Press it once to

select the AUTO mode, or twice to select

MANUAL mode.

4. In AUTO mode, use the + and – buttons to

select the desired temperature.

The selected temperature (in degrees

celsius) will flash several times to indicate

that it is set. The screen will then return

to displaying the current room

temperature. The thermostat will continue

to vary the heat output to maintain your

selected temperature.

5. In MANUAL mode, use the + and –

buttons to select the desired heat setting,

from H1 to H5. The selected setting will

flash several times to indicate that it is

set. The screen will then return to

displaying the room temperature. The

heater will operate constantly at the

selected heat level, without monitoring the

room temperature.

6. To switch between operating modes or turn

the heater off, press the standby button.

7. Switch the power off at the power outlet

and unplug the heater when not in use.

Using your heater

MF2000 Micro Furnace Ceramic Disc Heater

1. Place the heater on a flat level surface,

approximately 1 metre from any wall or

other objects such as furniture, curtains,

plants or combustible material, and ensure

that the air intake and outlet are clear of

obstructions.

Note: For most efficient heating, place the

heater on the floor where the air is cooler,

near an outside door, the bottom of a

staircase, or where colder air is most likely

to be entering the room.

2. Insert the plug into a 230-240V power

outlet and turn the power on. The power

light will illuminate.

3. To operate the heater, select HEAT on

the mode dial. Rotate the thermostat dial

to select the desired temperature setting.

Once the selected temperature level has

been reached, the thermostat will

constantly vary the heat output to

maintain it.

4. To operate the fan, select FAN on the

mode dial. Rotate the thermosat dial to

minimum.

5. To switch the heater off, select OFF on the

mode dial.

6. Switch the power off at the power outlet

and unplug the heater when not in use.

Using your heater (continued)

MF1500 Micro Furnace Ceramic Disc Heater

Ensure the heater is switched off and

disconnected from the power outlet before

cleaning.

Carefully wipe the exterior of the heater with

a soft damp cloth and dry thoroughly.

Cleaning the dust filter

The dust filter collects dirt and dust from the

air circulating through the heater.

To clean the filter, remove from the unit and

rinse under warm water. Allow to dry

completely before replacing on the heater.

Storage

Store your heater in a cool dry place when

not in use. Store the heater in its carton if

possible.

Care and cleaning

Consumer Hotline

Australia

1800 025 059

New Zealand

(09) 912 0747

www.sunbeam.com.au

is a registered trademark of Sunbeam

Corporation Limited.

is a registered trademark of Pelko Electric

Company and is used under licence by Sunbeam

Corporation Limited.

Made in China. Due to minor changes in design or

otherwise, the product you buy may differ from the one

shown in this leaflet.

Backed by Sunbeam‘s 3 Year Replacement Guarantee and

National Service Network.

SUNBEAM CORPORATION LIMITED 2004.

(INCORPORATED IN N.S.W.) A.C.N. 000 006 771

Sunbeam Corporation is a division of GUD Holdings Ltd.

For more information or advice on this or any other

Sunbeam appliance, visit www.sunbeam.com.au or

contact the Sunbeam Consumer Service Line.

Australia 1800 025 059

New Zealand (09) 912 0747.

Sunbeam Bedding MF2000 User manual

Brand: Sunbeam Bedding

Model: MF2000

Category: Thermostats

Type: User manual

This manual is also suitable for

MF1500

Download PDF

report

Sunbeam Bedding MF2000 User manual

This manual is also suitable for

Sunbeam Bedding MF2000 User manual

Related papers

Other documents