Samsung WS28V53NS8XXEC User manual

COLOR TELEVISION RECEIVER

Chassis : KS3A(P)_50Hz(REV. 4)

Model : WS28V53NS8XXEC

WS28V55VS8XXEC

WS32V56VS8XXEC

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Reference Information

Specifications

Alignment and Adjustments

Troubleshooting

Exploded Views and Parts List

Electrical Parts List

Block Diagrams

Wiring Diagram

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protective

devices are replaced. Restore any missing

protective shields.

2. When reinstalling the chassis and its

assemblies, be sure to restore all protective

devices, including: nonmetallic control knobs

and compartment covers.

3. Make sure that there are no cabinet openings

through which people—particularly

children—might insert fingers and contact

dangerous voltages. Such openings include

the spacing between the picture tube and the

cabinet mask, excessively wide cabinet

ventilation slots, and improperly fitted back

covers.

If the measured resistance is less than 1.0

megohm or greater than 5.2 megohms, an

abnormality exists that must be corrected

before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):

Warning: Do not use an isolation

transformer during this test. Use a leakage-

current tester or a metering system that

complies with American National Standards

Institute (ANIS C101.1, Leakage Current for

Appliances), and Underwriters Laboratories

(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug

the AC line cord directly into the power

outlet. With the unit’s AC switch first in the

ON position and then OFF, measure the

current between a known earth ground (metal

water pipe, conduit, etc.) and all exposed

metal parts, including: antennas, handle

brackets, metal cabinets, screwheads and

control shafts. The current measured should

not exceed 0.5 milliamp. Reverse the power-

plug prongs in the AC outlet and repeat the

test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:

With the unit’s AC plug disconnected from the

AC source, connect an electrical jumper across

the two AC prongs. Connect one lead of the

ohmmeter to an AC prong. Connect the other

lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to

prohibit X-ray emissions. To ensure continued

X-ray protection, replace the picture tube only

with one that is the same type as the original.

Carefully reinstall the picture tube shields and

mounting hardware; these also provide X-ray

protection.

8. High Voltage Limits:

High voltage must be measured each time

servicing is done on the B+, horizontal

deflection or high voltage circuits.

Correct operation of the X-ray protection

circuits must be reconfirmed whenever they

are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include

the X–ray Protection Specifications Label, and

the Product Safety and X-ray Warning Note on

the service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGE

CURRENT

TESTER

DEVICE

UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

EARTH

GROUND

(READING SHOULD

NOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential

hazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified

limits by close-tolerance, safety-related

components and adjustments. If the high

voltage exceeds the specified limits, check

each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or

electrical design of this unit. Example: Do not

add auxiliary audio or video connectors. Such

alterations might create a safety hazard. Also,

any design changes or additions will void the

manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically

connected directly to one conductor of the AC

power cord. If an isolation transformer is not

used, these units may be safely serviced only

if the AC power plug is inserted so that the

chassis is connected to the ground side of the

AC source.

To confirm that the AC power plug is inserted

correctly, do the following: Using an AC

voltmeter, measure the voltage between the

chassis and a known earth ground. If the

reading is greater than 1.0V, remove the AC

power plug, reverse its polarity and reinsert.

Re-measure the voltage between the chassis

and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground,

regardless of the AC plug polarity. These units

can be safely serviced only if an isolation

transformer inserted between the receiver and

the power source.

13. Some TV chassis have a secondary ground

system in addition to the main chassis ground.

This secondary ground system is not

isolated from the AC power line. The two

ground systems are electrically separated by

insulating material that must not be defeated

or altered.

14. Components, parts and wiring that appear to

have overheated or that are otherwise

damaged should be replaced with parts that

meet the original specifications. Always

determine the cause of damage or

overheating, and correct any potential

hazards.

15. Observe the original lead dress, especially

near the following areas: Antenna wiring,

sharp edges, and especially the AC and high

voltage power supplies. Always inspect for

pinched, out-of-place, or frayed wiring. Do

not change the spacing between components

and the printed circuit board. Check the AC

power cord for damage. Make sure that leads

and components do not touch thermally hot

parts.

16. Picture Tube Implosion Warning:

The picture tube in this receiver employs

“integral implosion” protection. To ensure

continued implosion protection, make sure

that the replacement picture tube is the same

as the original.

17. Do not remove, install or handle the picture

tube without first putting on shatterproof

goggles equipped with side shields. Never

handle the picture tube by its neck. Some

“in-line” picture tubes are equipped with a

permanently attached deflection yoke; do not

try to remove such “permanently attached”

yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have

special safety-related characteristics which

might not be obvious from visual inspection.

These safety features and the protection they

give might be lost if the replacement

component differs from the original—even if

the replacement is rated for higher voltage,

wattage, etc.

Components that are critical for safety are

indicated in the circuit diagram by shading,

( ) or ( ).

Use replacement components that have the

same ratings, especially for flame resistance

and dielectric strength specifications.

A replacement part that does not have the

same safety characteristics as the original

might create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

1-2 Servicing Precautions

1. Servicing precautions are printed on the

cabinet. Follow them.

2. Always unplug the unit’s AC power cord from

the AC power source before attempting to:

(a) Remove or reinstall any component or

assembly, (b) Disconnect an electrical plug or

connector, (c) Connect a test component in

parallel with an electrolytic capacitor.

3. Some components are raised above the printed

circuit board for safety. An insulation tube or

tape is sometimes used. The internal wiring is

sometimes clamped to prevent contact with

thermally hot components. Reinstall all such

elements to their original position.

4. After servicing, always check that the screws,

components and wiring have been correctly

reinstalled. Make sure that the portion around

the serviced part has not been damaged.

5. Check the insulation between the blades of the

AC plug and accessible conductive parts

(examples: metal panels, input terminals and

earphone jacks).

6. Insulation Checking Procedure: Disconnect the

power cord from the AC source and turn the

power switch ON. Connect an insulation

resistance meter (500V) to the blades of the AC

plug.

The insulation resistance between each blade

of the AC plug and accessible conductive parts

(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.

Do not apply AC power to the unit (or any of

its assemblies) unless all solid-state heat sinks

are correctly installed.

8. Always connect a test instrument’s ground

lead to the instrument chassis ground before

connecting the positive lead; always remove

the instrument’s ground lead last.

Precautions

Samsung Electronics 1-3

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between

the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devices

are easily damaged by static electricity. Such

components are called Electrostatically

Sensitive Devices (ESDs); examples include

integrated circuits and some field-effect

transistors. The following techniques will

reduce the occurrence of component damage

caused by static electricity.

2. Immediately before handling any semicon

ductor components or assemblies, drain the

electrostatic charge from your body by

touching a known earth ground. Alternatively,

wear a discharging wrist-strap device. (Be

sure to remove it prior to applying power—

this is an electric shock precaution.)

3. After removing an ESD-equipped assembly,

place it on a conductive surface such as

aluminum foil to prevent accumulation of

electrostatic charge.

4. Do not use freon-propelled chemicals. These

can generate electrical charges that damage

ESDs.

5. Use only a grounded-tip soldering iron when

soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.

Many solder removal devices are not rated as

“anti-static”; these can accumulate sufficient

electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its

protective package until you are ready to

install it. Most replacement ESDs are

packaged with leads that are electrically

shorted together by conductive foam,

aluminum foil or other conductive materials.

8. Immediately before removing the protective

material from the leads of a replacement ESD,

touch the protective material to the chassis or

circuit assembly into which the device will be

installed.

9. Minimize body motions when handling

unpackaged replacement ESDs. Motions such

as brushing clothes together, or lifting a foot

from a carpeted floor can generate enough

static electricity to damage an ESD.

Precautions

1-4 Samsung Electronics

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

Reference Information

Samsung Electronics 2-1

2. Reference Information

2-1 Tables of Abbreviations and Acronyms

A

Ah

Å

dB

dBm

°C

°F

°K

F

G

GHz

g

H

Hz

h

ips

kWh

kg

kHz

kΩ

km

km/h

kV

kVA

kW

I

MHz

Ampere

Ampere-hour

Angstrom

Decibel

Decibel Referenced to One

Milliwatt

Degree Celsius

Degree Fahrenheit

degree Kelvin

Farad

Gauss

Gigahertz

Gram

Henry

Hertz

Hour

Inches Per Second

Kilowatt-hour

Kilogram

Kilohertz

Kilohm

Kilometer

Kilometer Per Hour

Kilovolt

Kilovolt-ampere

Kilowatt

Liter

Megahertz

MV

MW

MΩ

m

µA

µF

µH

µm

µs

µW

mA

mg

mH

mI

mm

ms

mV

nF

Ω

pF

Ib

rpm

rps

s

V

VA

W

Wh

Megavolt

Megawatt

Megohm

Meter

Microampere

Microfarad

Microhenry

Micrometer

Microsecond

Microwatt

Milliampere

Milligram

Millihenry

Milliliter

Millimeter

Millisecond

Millivolt

Nanofarad

Ohm

Picofarad

Pound

Revolutions Per Minute

Revolutions Per Second

Second (Time)

Volt

Volt-ampere

Watt

Watt-hour

Table 2-1 Abbreviations

Reference Information

2-2 Samsung Electronics

Table 2-2 Table of Acronyms

ABL

AC

ACC

AF

AFC

AFT

AGC

AM

ANSI

APC

A/V

AVC

BAL

BPF

B-Y

CATV

CB

CCD

CCTV

Ch

CRT

CW

DC

DVM

EIA

ESD

FBP

FBT

FF

FM

FS

GND

G-Y

H

HF

HI-FI

IC

IF

Automatic Brightness Limiter

Alternating Current

Automatic Chroma Control

Audio Frequency

Automatic Frequency Control

Automatic Fine Tuning

Automatic Gain Control

Amplitude Modulation

American National Standards Institute

Automatic Phase Control

Automatic Picture Control

Audio-Video

Automatic Volume Control

Balance

Bandpass Filter

Blue-Y

Community Antenna Television (Cable TV)

Citizens Band

Charge Coupled Device

Closed Circuit Television

Channel

Cathode Ray Tube

Continuous Wave

Direct Current

Digital Volt Meter

Electronics Industries Association

Electrostatic Discharge

Electrostatically Sensitive Device

Feedback Pulse

Flyback Transformer

Flip-Flop

Frequency Modulation

Fail Safe

Ground

Green-Y

High

High-Frequency

High Fidelity

Inductance-Capacitance

Integrated Circuit

Intermediate Frequency

I/O

L

LED

LF

MOSFET

MTS

NAB

NEC

NTSC

OSD

PCB

PLL

PWM

QIF

R

RC

RF

R-Y

SAP

SAW

SIF

SMPS

S/N

SW

TP

TTL

TV

UHF

UL

UV

VCD

VCO

VCXO

VHF

VIF

VR

VTR

VTVM

TR

Input/output

Left

Low

Light Emitting Diode

Low Frequency

Metal-Oxide-Semiconductor-Field-Effect-Tr

Multi-channel Television Sound

National Association of Broadcasters

National Electric Code

National Television Systems Committee

On Screen Display

Printed Circuit Board

Phase-Locked Loop

Pulse Width Modulation

Quadrature Intermediate Frequency

Right

Resistor & Capacitor

Radio Frequency

Red-Y

Second Audio Program

Surface Acoustic Wave(Filter)

Sound Intermediate Frequency

Switching Mode Power Supply

Signal/Noise

Switch

Test Point

Transistor Transistor Logic

Television

Ultra High Frequency

Underwriters Laboratories

Ultraviolet

Variable-Capacitance Diode

Voltage Controlled Oscillator

Voltage Controlled Crystal Oscillator

Very High Frequency

Video Intermediate Frequency

Variable Resistor

Video Tape Recorder

Vacuum Tube Voltmeter

Transistor

Table 2 - 3 IC Line - Up

NO

1

DESCRIPTION

Video Processor

Multistandard Sound Processor

MICOM, TTX(MTP)

EEPROM

Audio AMP

RGB Drive AMP Hybrid IC

Vertical IC

Horizontal Drive IC

E/W Drive IC

SPS Controllor

Bridge Diode

Photo Coupler

5V Controlled Regulator

Rectifier Diode

3.3V Regulator

6V Regulator

8V Controlled Regulator

3.3V Regulator

MICOM Reset IC

IIC Level Shifter

Reference Information

Samsung Electronics 2-3

2-2 IC Line Up

LOC. NO

IC201S

IC601

IC901

IC902

IC602

HIC201

HIC202

HIC203

HIC204

IC301

Q402

Q401

D414

IC401

Q404

IC801S

D801S

PC801S

IC802

D805

D806

D807

D802

IC201

IC804

IC803

IC903

IC904

Q909

Q910

BOARD

MAIN

SPEC

VDP3130Y

MSP3411G

SDA555X

KS24L161

TDA7297

DRGB001

LA7845

KSC2073-H2

KSD5703

FMP-3FU

KA393

IRF620

3S1265RB

3S1265RD

RBV606

PC123Y

KA78R05

FML-G12S

FMG-G2CS

KA78RM33

KA7806

KA78R08

KA78RM33

KIA7025AP

2N700

REMARK

Refer to Table 2-3-1

Refer to Table 2-3-2

Refer to Table 2-3-3

VM Option

HC401

HC801

2-4 Samsung Electronics

Table 2 - 3 IC Line - Up

NO

2

3

4

5

DESCRIPTION

Video Output AMP R.G.B Drive

Push-Pull (VM)

TR-Power (TILT)

OP-AMP (TILT)

OP-AMP

TR-Power

Video Switching IC with Adder Output

High-end Picture-In Picture IC

1-TUNER PIP

3.3V Regulator

LOC. NO

TU01S

TU02S

IC501

IC502

IC503

QF04

QF05

QG02

QG03

ICG01

ICH01

QH01

ICS01

ICP01

ICP02

SPEC

TCL3101PD09A9(S)

TDA5109

TDA6101Q

2SC2344

2SA1011

KSA940

KSD2073-H2

KA4558

2SC4636RB

TEA6425

SDA9489X

SDA9489

EZ1086CM

REMARK

Refer to Table 2-3-4

Refer to Table 2-3-5

FLAT

Option

BOARD

CRT

DOUBLE

FOCUS

V-S/W

PIP

Reference Information

SPEC

VDP3108B

VDP3112B

VDP3120B

VDP3130Y

FUNCTION

50Hz Basic

50Hz, 2H Comb Filter

50Hz, 2H Comb Filter, Horizontal Scaler

50Hz, 2H Comb Filter, DVD Input

REMARK

Table 2-3-1 VIDEO IC (IC201S)

SPEC

MSP3400D

MSP3410D

MSP3411G

FUNCTION

Multistandard, A2 Stereo

Multistandard, A2 Stereo, Nicam

Multistandard, A2 Stereo, Nicam, Vitual Dolby

REMARK

Table 2-3-2 SOUND IC (IC601)

Reference Information

Samsung Electronics 2-5

SPEC

TDA7297

FUNCTION

15W x 2CH, 10W x 2CH

REMARK

SPEC

TCLS3101PD09A(S)

TCPS3000P

TCPS3001PD09E(S)

TCPW3001PD09A(S)

TCL3101PD16A

FUNCTION

CS with LNA Function

CS

CZ, CW

CS

REMARK

Main(Old)

India

Main(New)

SPEC

TCPS3000PC09B(S)

TCPS3000PC16B

FUNCTION

CS

REMARK

Sub(Old()

Sub(New)

TCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function.

Table 2-3-3 SOUND AMP (IC602)

Table 2-3-4 1’st TUNER (TU01S)

Table 2-3-5 2’nd TUNER (TU02S)

Note

2-6 Samsung Electronics

MEMO

Specifications

Samsung Electronics 3-1

3. Specifications

Specifications are subject to change.

Television

System

Antena Input

CS

Power

Consumption

Requirements

Frequency

Sound

Output

Effect

Jacks

Front

(AV2)

Back

PAL/SECAM-B/G,D/K,L,I, NTSC-M

130W (Applied When 29” Flat)

220V Only

Free Voltage

50/60Hz

15W x 2CH

10W x 2CH

5W x 2CH

Virtual Dolby

Turbo Sound

Pseudo Stereo

RCA Input

S-VHS

Head-Phone

RCA99(AV2 Input/Out)

2Scart Input/Output

DVD Input(YPbPr)

AV2 Monitor Audio Output

S-VHS

75ohms, Coaxial Cable

Not Present R815

Option

AV1 : Scart I/O, RGB Input,

RF Out

AV2 : Scart I/O, Monitor Out

Option

N

P

PF

PT

PW

MT

NT

WT

GW

Function

NICAM

2 TUNER PIP

2 TUNER PIP, NICAM, TTX

2 TUNER PIP, A2 STEREO, TTX

2 TUNER PIP, A2 STEREO

2 TUNER MULTI PIP, A2 STEREO,

NICAM, TTX

A2 STEREO, TTX

1 TUNER PIP, A2 STEREO, TTX

NOTE

“NICAM” means that

A2 STEREO + NICAM

Specifications for Model Name (Ex. CS29A6??8X/HAC)

29 Inch

21 Inch

3-2 Samsung Electronics

MEMO

Alignment and Adjustments

Samsung Electronics 4-1

4. Alignment and Adjustments

4-1 General Alignment Instructions

1. Usually, a color TV-VCR needs only slight

touch-up adjustment upon installation. Check

the basic characteristics such as height,

horizontal and vertical sync and focus.

2. Observe the picture for good black and white

details. There should be objectionable color

shading; if color shading is present,

demagnetize, perform purity and convergence

adjustments described below.

3. Use the specified test equipment or its

equivalent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a

sweep generator might overload the front-end

of the TV. When inserting signal markers, do

not allow the marker generator to distort test

results.

6. Connect the TV only to an AC power source

with voltage and frequency as specified on the

backcover nameplate.

7. Do not attempt to connect or disconnect any

wires while the TV is turned on. Make sure

that the power cord is disconnected before

replacing any parts.

8. To protect against shock hazard, use an

isolation transformer.

4-2 Automatic Degaussing

A degaussing coil is mounted around the

picture tube, so that external degaussing after

moving the TV should be unnecessary. But

the receiver must be properly degaussed upon

installation.

The degaussing coil operates for about 1

second after the power is switched ON. If the

set is moved or turned in a different direction,

the power should be OFF for at least 10

minutes.

If the chassis or parts of the cabinet become

magnetized, poor color purity will result. If

this happens, use an external degaussing coil.

Slowly move the degaussing coil around the

faceplate of the picture tube and the sides and

front of the receiver. Slowly withdraw the coil

to a distance of about 6 feet before turning

power OFF.

If color shading persists, perform the

following Color purity and Convergence

adjustments.

4-3 High voltage Check

CAUTION : There is no high voltage adjustment

on this chassis. The B+ power supply should be

+135 volts (with full color- bar input and normal

picture level).

1. Connect a digital voltmeter to the second

anode of the picture tube.

2. Turn on the TV. Set the Brightness and

Contrast controls to minimum (zero beam

current).

3. Adjust the Brightness and contrast controls to

both extremes. Ensure that the high voltage

does not exceed 32 KV under any conditions.

Alignment and Adjustments

4-2 Samsung Electronics

4-5 SCREEN Adjustment

1. Input Toshiba Pattern

2. Enter “Service Mode”.(Refer to “Service Mode”)

3. Select “G2-Adjust”.

4. Set the values as example(Refer to page4-24).

4-4 Dynamic Focus Adjustment

1. A dynamic focus adjustment should be done

after replacing the CRT PCB, FBT or CRT.

2. Input a crosshatch pattern.

3. Enter “ STANDARD “ in video mode.

4. Turn the Dynamic focus VR fully clockwise

(maximum).( )

5. Turn the Static focus VR fully

counterclockwise (maximum).( )

6. Slowly turn the static focus VR

counterclockwise. Adjust until the

vertical line in the middle of the screen

has maximum clarity.( )

7. Slowly turn the dynamic focus VR (clockwise)

and adjust the 3rd horizontal line for

maximum clarity.( )

8. Repeat 4-7, if necessary.

STATIC FOCUS VR

DYNAMIC FOCUS VR

H

V

SCREEN

❷

❶

❷

❶

❷

❶

❷

❶

ex) IBRM = 220

WDRV = 35

CDL = 220

COLR G B = 150 150 150

Alignment and Adjustments

Samsung Electronics 4-3

When you do not have Toshiba Pattern, follow this method.

1. Set the TV on the condition that AV mode no signal(black)

2. Enter the “Menu” and set the mode to blue screen off.

3. Enter the “Service Mode”.

4. Select “ G2-Adjust”.

5. Set the values as example(Refer to page4-24).

ex) IBRM = 220

WDRV = 35

CDL = 220

COLR G B = 150 150 150

6. Turn the SCREEN VR until the value of “ MRCR G B” is about 120. Do not mind that

the “OSD” Color is red.

■ After completing G2-Adjust, follow this procedure.

① Enter the “Video Adjust 1”.

➁ Choose any item in menu. (ex. Select “Red Cutoff”)

➂ Change the value of item you select, and recover the value.

For example, when the value of “Red Cutoff” is 127, change the value to 128 and restore

the value to 127.

If you do not follow this procedure, the picture may be abnormal.

For example, when the TV set is on, the picture becames brighter gradually.

Note 1.

5. Turn the SCREEN VR until “MRCR G B” and “MRWDG” are green and those value are about 100.

(The incorrect SCREEN Voltage may result that “MRCR G B” and “MRWDG” should be red)

Alignment and Adjustments

4-4 Samsung Electronics

4-6 E

2

PROM (IC902) Replacement

1. When IC902 is replaced, all adjustment data revert to the initial values.

So, all adjustment values when servicing should be readjusted.

2. After IC902 is replaced, connect the AC power supply cord.

3. Turn the power switch ON.

4. In stand-by, warm up the TV for at least 10 seconds.

5. Power on the TV.

4-7 White Balance Adjustment

■ Equipment : Color-Analyzer (CA-100)

■ Input Signal : Pattern signal (Toshiba pattern)

1. Select STANDARD from the menu.

2. Input an 100% White pattern.

3. Enter the “Service Mode”. (Refer to “4-8 Service Mode”)

4. Warm up the TV set at least for 30 minutes.

5. Input a Toshiba pattern signal.

6. Enter the “Video Adjust1”.

- Adjust “Sub Contrast” so that Y (luminance) becomes 40 ft ± 3.

- Use “Red Drive” and “ Blue Drive” to adjust High-Light (x : 290, y : 300)

- Adjust “Sub Bright” so that Y (luminance) becomes 1.3ft ± 0.3.

- Use “Red Cutoff” and “Blue Cutoff” to adjust Low-Light (x : 290, y : 300).

7. Adjust CA-100 so that the final adjustment value can be fixed.

8. Use the Channel Up/Down (▲/▼) buttons to move the cursor on the adjustment modes.

9. Use the Volume +/- buttons to change the adjustment value.

■ SMPS Controller differentiol List

LOC.

DZ808

C811

C828

1265RD

1265RB

SPEC

MTZ8.28

47NF

221.50V

SPEC

MTZ8.28

47NF

221.50V

LOC.

DZ808

C811

C828

■ Background : It is occurred to service confusion

■ Cause : CRT Socket PCB change as CRT changing from Double Focus to Single Focus

■ How to service

Code : It is different to CRT Socket Code per focus type

Case :

1. Using CRT Socket PCB for Single Focus at CRT for Double Focus

(1) Change the CRT Socket in PCB(Single → Double).

(2) Cut the red-colored focus wire of FBT in set.

(3) Connect the wires at Focus terminal like picture #1 for short circuit using red-colored focos

wire of FTB.

2. Using CRT Socket PCB for Double Focus at CRT for Single Focus

(1) Change the CRT Socket in PCB(Double → Single).

(2) Cut the red-colored focus wire of FBT in set like picture #2.

❈ You mus tape the isolation parts for safety.

Alignment and Adjustments

Samsung Electronics 4-5

KS3A 29” Flat 50Hz, CRT Change(Double Focus

→→

Single Focu)

Note 2.

CRT Socket

For Double Focus

For Single Focus

Code No

3704-001032

3704-000114

Alignment and Adjustments

4-6 Samsung Electronics

4-8 Factory Adjustment

1. To enter the “Service Mode”, Press the remote-control keys in this sequence :

- If you do not have Factory remote-control

- If you have Factory remote-control

2. After the Service Mode is entered, the initial screen is as shown in the figure below.

*

Service

Deflection

Video Adjust 1

Video Adjust 2

Video Adjust 3

Option(81h 0Ch)

Reset

G2-Adjust

Others

3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters.

- When CRT, CRT PCB, FBT, E

2

PROM (sometimes MICOM) is replaced, the adjustment values

should be controlled.

- After the Service adjustment is completed, Do not select “Reset” in the service mode menu.

(After above procedure is done, power is on initially and the “Plug and Play” will be operated.)

PICTURE OFF PICTURE ON

DISPLAY

()

MENU

MUTE

PICTURE ON

DISPLAY

()

FACTORY

4-8-1 Service Mode

*

These hexa digits are check sum value which

depends on the MICOM.

If check sum value is changed, the value of

E

2

PROM Data newly initialed.

Note 3.

Alignment and Adjustments

Samsung Electronics 4-7

4-8-2 Memory Data

4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

OSD

V Amp

V Shift

V Slope

V SC

H EW

H Trapizium

H Parabola

H Symmetry

H Corner

H Shift

Zoom 4:3 Para

4:3~16:9 Para

Wide-4:3 Para

Wide-Zoom Para

Wide-Zoom2 Para

Zoom1 Amp

Zoom2 Amp

TTX Position

D-TTX Posi

RGB Shift

PIP Contrast

PIP Tint

PIP V.Move(VSPDEL)

PIP PAL V.Pos

PIP NTSC V.Pos

PIP H.Pos

PIP BLKLG

Function

Adjusts Vertical picture size. Adjust 4:4 upper and below picture size in

lion head pattern at factory.

Adjusts Vertical picture position

Adjusts Vertical Slope Correction

Adjusts Vertical s-correction

Horizontal east west width. Adjust 5:5 left and right picture size in lion

head pattern at factory.

Adjusts horizontal Trapezium.

Adjusts Horizontal Parabola.

Adjusts Picture upper and below horizontal Symmetry.

Adjusts Picture upper and below Horizontal Corner.After adjust the

Parabola, adjust H corner vertical Line upper and below has nonlinear.

Adjusts Horizontal Position.

Corrects the vertical linearity in Zoom mode of P-SIZE.

The data depends on CRT (see data above)

Corrects the vertical linearity in 16:9 mode of P-SIZE.

The data differs according to CRT (see data above).

Corrects the vertical linearity in wide mode of P-SIZE.

The data differs according to CRT (see data above).

Corrects the vertical linearity in wide mode of P-SIZE.

The data differs according to CRT (see data above).

Corrects the vertical linearity in wide mode of P-SIZE.

The data differs according to CRT (see data above).

Adjusts vertical amplitude in zoom1

Adjusts vertical amplitude in zoom2. Zoom2 mode is a manual zoom

mode

Sets TTX Position.

Double -TTX position.

Adjusts RGB input signal Horizontal position

Adjusts PIP contrast.

Adjusts PIP Tint. It is a function to control color phase of NTSC signal in

PIP

PIP vertical sync pulse delay. When changing data, PIP jitters at two

points.

In this case, the PIP VSPDEL is set to the center between two points.

Adjusts Vertical position of PIP in PAL system.

Adjusts Vertical position of PIP in NTSC system.

Adjusts Horizontal Position of the PIP.

PIP blanking level green(PIP low light white balance).

It is used to control low light white balance in PIP

Remark

Adjust

Fix

Adjust

Fix

Adjust

Fix

Adjust

Fix

Page is loading ...

Samsung WS28V53NS8XXEC User manual

This manual is also suitable for

Samsung WS28V53NS8XXEC User manual

Related papers

Other documents