Ricoh Aficio SP 1000SF User manual

Brand: Ricoh

Model: Aficio SP 1000SF

Category: Print & Scan

Type: User manual

This manual is also suitable for

TELECOM

Read this manual carefully before you use this machine and keep it handy for future reference.

For safe and correct use, be sure to read the Safety Information in this manual before using the machine.

Operating Instructions

LASER MFP

SP 1000SF

- I -

Contents

Security 1

Security directives 1

Laser safety 1

For Europe/Asia 1

For North America 2

Declaration of conformity 2

Notice to Users in EEA Countries 2

Notice to Users Accessing Analog PSTN

in EEA Countries 2

Symbols for the main power switch 2

Positions of Warning and Caution labels

on the machine 2

FCC Compliance 3

Note to users in the United States of America 3

Notice about the Telephone Consumer

Protection Act (Valid in USA only) 4

Note to users in Canada 4

Remarque concernant les utilisateurs au Canada 4

FCC Requirements 4

Notice to users (New Zealand) 5

Environment 6

Batteries and rechargeable batteries 6

The product 6

Users in the EU, Switzerland and Norway 6

All Other Users 6

Software use license 7

Definition 7

License 7

Property 7

Duration 7

Warranty 7

Responsibility 7

Development 7

Registered trademarks 8

Notice 8

Installation 9

Location conditions 9

Cautions of use 9

Safety information 10

Safety During Operation 10

Power Supply 11

For Fax or Telephone 11

Rules for use symbols 11

Terminal description 12

Command panel 13

Presentation 13

Entering Characters Using

the Alpanumerical keypad 13

Accessing terminal functions 14

Packaging contents 15

Device installation 15

Installing the document feeder 15

Loading paper 15

Loading paper in the paper tray 15

Handling of paper 15

Humidity control 15

Handling the unit 16

Operator shocks 16

Moving the unit 16

Handling the Toner Cartridge 16

Feed cassette paper insertion 16

Cartridge installation 16

Paper delivery stop 17

Starting your device 17

Device connection 17

Paper insertion in the manual input tray 18

Copy 19

Simple copy 19

ECO mode copy 19

Sophisticated copy 19

Special setup for the copy 19

Resolution setup 20

Zoom setup 20

Analysis origin setup 20

Contrast setup 20

Luminosity setup 20

Paper type setup 20

Paper tray selection 20

Sheet-feed analysis margins setup 21

Flat-bed analysis margins setup 21

Left and right printing margins setup 21

Top and bottom printing margins setup 21

Format paper setup 21

Fax 22

Fax transmission 22

Immediate transmission 22

Delayed transmission 22

Transmission with auto redial 22

Fax reception 22

Fax answering device 23

Saving an access code 23

Activating / Deactivating the answering device 23

Printing fax messages stored in the memory 23

Fax rerouting (Forwarding) 23

Activating rerouting 23

Setting the re-direction contact 23

Printing rerouted documents 24

Rerouting fax messages to a USB memory key 24

Activating rerouting 24

Printing rerouted documents 24

Transmission waiting queue 24

Performing immediate transmission

from the waiting queue 24

Consulting or modifying the waiting queue 24

Deleting a transmission in memory 24

Printing a document in waiting or in deposit 25

Printing the waiting queue 25

Cancelling a transmission in progress 25

Deposit and Polling 25

Placing a document in deposit 25

Polling a deposited document 25

Parameters/Setup 26

Date/Time 26

Your fax number/Your name 26

Type of network 26

Geographical settings 26

Country 26

Telecommunication Network 26

Language 27

SP 1000SF

- II -

Contents

Local prefix 27

Transmission report 27

Document feed type 27

Economy period 28

Reception Mode 28

Reception without paper 28

Number of copies 28

Fax or PC reception 28

Received faxes reduction mode 28

Technical Parameters 29

Printing the functions guide 30

Printing the logs 30

Print the list of setups 30

Lock the machine 30

Lock the keyboard 31

Lock the numbers 31

Read the counters 31

Sent pages counter 31

Received pages counter 31

Scanned pages counter 31

Printed pages counter 31

Display the consumables status 31

Calibrate your scanner 31

Directory 32

Creating Speed dial 32

Creating Group dial 32

Modifying a record 32

Deleting a record 32

Printing the directory 33

Saving/Restoring the directory

(Smart card option) 33

USB memory key 34

Use of the USB memory key 34

Print your documents 34

Print the list of files located in the key 34

Print the files located in the key 34

Delete your files located in the key 34

Analyse the USB memory key content 35

Save a document on a USB memory key 35

Activate/deactivate file automatic deletion

on a USB memory key 35

PC Features 37

Introduction 37

Configuration requirements 37

Installation 37

Install the software on your PC 37

Connections 39

USB Connection 39

Uninstall the software from your PC 39

Multifunction Terminal's Supervision 40

Checking the connection between the PC

and the multifunction machine 40

MF Director 40

Graphical presentation 40

Utilities and applications activation 40

MF Monitor 41

Graphical presentation 41

Display the consumable status 41

Scan To 41

Companion Suite Pro LL functionalities 41

Document analysis 41

Analysis with Scan To 41

Analysis from a TWAIN compatible software 42

Character recognition software (OCR) 42

Printing 42

Printing with the multifunction machine 42

Address book 42

Add a contact to the terminal address book 42

Add a group to the terminal address book 43

Manage the address book 43

Modify the information related to a contact 43

Modify a group 43

Delete a contact or a group from

the address book 43

Print the address book 44

Import or export a directory 44

Import a directory 44

Save your address book 44

Fax communications 44

Presentation of the Fax window 44

Send a fax 44

Send a fax from the hard disk or the terminal 44

Send a fax from application 45

Receive a fax 45

Follow-up of fax communications 46

The outbox 46

The send memory (items sent) 46

The outbox log 46

The inbox log 46

Fax parameters 46

Access to fax parameters 46

Description of the tab Log and Report 46

Description of the tab Fax Parameters 47

Cover sheet 47

Creating a cover sheet 47

Description of the tab Cover page 48

Creating a cover page template 48

Maintenance 50

Service 50

General information 50

Toner cartridge replacement 50

Issues with smart cards 51

Cleaning 51

Scanner reading system cleaning 51

Printer cleaning 51

Printer external cleaning 51

Printer issues 51

Error messages 51

Paper jam 52

Scanner issues 52

Miscellaneous issues 52

Communication errors 53

Transmission from the feeder 53

Transmission from memory 53

Communication error codes 53

General codes 53

Specifications 55

Physical specifications 55

Electrical specifications 55

Environmental specifications 55

Peripheral specifications 55

SP 1000SF

- 1 -

1 - Security - Certification - Environment - Licence

Security

Security directives

Before turning on your device, check that the outlet that you are going to plug it into conforms to the indications shown

on the information plate (voltage, current, power network frequency) located on your device. This device shall be

connected to a single phase power network. The device shall not be installed on bare ground.

Batteries and rechargeable batteries, packaging and electric and electronic equipment (EEE), shall be thrown away,

as specified by the Instructions of the ENVIRONMENT chapter of this manual.

Because of the device model, the power connector is the only way to disconnecting the device from the power network,

that is why it is imperative to apply the following safety measures: your device shall be connected to a power outlet

located nearby. The outlet shall be easily accessible.

Your device is delivered with a grounded power cord. It is imperative to connect a grounded connector to a grounded

outlet connected to the building earthing.

For installation conditions and safe use precautions, refer to chapter Installation, page 9.

Laser safety

For Europe/Asia

This machine is considered a class 1 laser device, safe for office/EDP use. The machine contains 1 class 3B laser

diode, 10.72 milliwatt, 760-780 nanometer wavelength for each emitter.

Direct (or indirect reflected ) eye contact with the laser beam might cause serious eye damage. Safety precautions and

interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.

The following label is attached on the rear side of the machine.

Repairs-maintenance: Repairs and maintenance should only be carried out by a

qualified technician. No user serviceable parts inside the machine. To reduce the risk

of electrical shock, you shall not proceed with these operations yourself, because by

opening or removing the lids, you could expose yourself to two hazards:

- The laser beam can cause irreversible eye damage.

- Avoid contact with powered parts because it can lead to electrical shock with

unfortunate consequences.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified in the

Operating Instructions might result in hazardous radiation exposure.

SP 1000SF

- 2 -

1 - Security - Certification - Environment - Licence

For North America

CDRH Regulations.

This equipment complies with requirements of 21 CFR subchapter J for class 1 laser products. This equipment contains

1 class 3B laser diode, 10.72 milliwatt, 760-780 nanometer wavelength for each emitter.

This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of

operation and maintenance.

Declaration of conformity

Notice to Users in EEA Countries

This product complies with the essential requirements and provisions of Directive 1999/5/EC of the European

Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and

the mutual recognition of their conformity.

Notice to Users Accessing Analog PSTN in EEA Countries

This product is designed to be able to access analog PSTN in all EEA countries. Local PSTN compatibility is dependent

on software switch settings. Please contact your service representative if relocating this product to another country. In

the event of problems, please contact your service representative in the first instance.

SP1000SF/ Aficio SP1000SF: The CE declaration of Comformity is available on the Internet at URL :

http://www.ricoh.co.jp/fax/ce_doc

Symbols for the main power switch

In accordance with IEC 60417, this machine uses the following symbols for the main power switch:

- means POWER ON.

- means POWER OFF.

Positions of Warning and Caution labels on the machine

This machine has labels for WARNING and CAUTION at the positions shown below. For safety, please

follow the instructions and handle the machine as indicated.

SP 1000SF

- 3 -

1 - Security - Certification - Environment - Licence

FCC Compliance

Note to users in the United States of America

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one more of the following

measures:

1 Reorient or relocate the receiving antenna.

2 Increase the separation between the equipment and receiver.

3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4 Consult the dealer or an experienced radio / TV technician for help.

SP 1000SF

- 4 -

1 - Security - Certification - Environment - Licence

Notice about the Telephone Consumer Protection Act (Valid in USA only)

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic

device, including FAX machines, to send any message unless such message clearly contains in a margin at the top or

bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification

of the business or other entity, or other individual sending the message and the telephone number of the sending

machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or

any other number for which charges exceed local or long-distance transmission charges.)

In order to program this information into your FAX machine, you should complete the following steps: Follow the FAX

HEADER programming procedure in the Parameter Setup chapter of the operating instructions to enter the business

identification and telephone number of the terminal or business. This information is transmitted with your document by

the FAX HEADER feature. In addition to the information, be sure to program the date and time into your machine.

Note to users in Canada

This Class B digital apparatus complies with Canadian ICES-003.

Remarque concernant les utilisateurs au Canada

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC Requirements

1 This equipment complies with Part 68 of the FCC rules and requirements adopted by the ACTA. On the cover

of this equipment is a label that contains, among other information, a product identifier in the format

US:AAAEQ##TXXXXX. If requested, this number must be provided to the telephone company.

2 This equipment uses the RJ11C USOC jack.

3 A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with

the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and

modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is

also compliant. See installation instructions for detail.

4 The REN is used to determine the number of devices that may be connected to a telephone line. Excessive

RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not

all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be

connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this

product is part of the product identifier that has the format US:AAAEQ##TXXXXX. The digits represented by ##

are the REN without a decimal point (e.g., 03 is a REN of 0.3).

5 If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice is not practical, the telephone

company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint

with the FCC if you believe it is necessary.

6 The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the telephone company will provide advance notice in order

for you to make necessary modifications to maintain uninterrupted service.

7 If trouble is experienced with this equipment, for repair or warranty information, please contact RICOH CORP.

CUSTOMER SUPPORT DEPT. at 1-800-FASTFIX. If the equipment is causing harm to the telephone network,

the telephone company may request that you disconnect the equipment until the problem is resolved.

8 In the event of operation problems (document jam, copy jam, communication error indication), refer to the solving

problems section in this manual.

9 Connection to party line service is subject to state tariffs. Contact the state public utility commission, public

service commission or corporation commission for information.

10 If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this

equipment does not disable your alarm equipment. If you have questions about what will disable alarm

equipment, consult your telephone company or a qualified installer.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

SP 1000SF

- 5 -

1 - Security - Certification - Environment - Licence

Notice to users (New Zealand)

• The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the

item complies with minimum conditions for connection to its network. It indicates no endorsement of the product

by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work

correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it

imply that any product is compatible with all of Telecom's network services.

• This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which

it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.

• This equipment shall not be set up to make automatic calls to the Telecom “111” Emergency Service.

• If a charge for local calls is unacceptable, the “Dial” button should NOT be used for local calls. Only the 7-digits

of the local number should be dialled from your telephone. DO NOT dial the area code digit or the “0” prefix.

• This equipment may not provide for the effective hand-over of a call to another device connected to the same

line.

• This device may be subject to ringing or bell tinkle when calls are made from another device on the same line.

If this occurs, the problem SHOULD NOT be referred to the Telecom Faults Service.

• This equipment should not be used under any circumstances, which may constitute a nuisance to other Telecom

customers. For example, repeated attempts to make unsolicited sales offers to the same number or group of

numbers, such as when a block of numbers terminate on the same PABX.

• The call log incorporated in this equipment does not record all answered calls. The call log, therefore may not

agree with the Telecom account which may include calls not shown on the log.

• Not all telephones will respond to incoming ring when connected to the extension socket.

SP 1000SF

- 6 -

1 - Security - Certification - Environment - Licence

Environment

The preservation of the environment is of importance to the manufacturer. The manufacturer wishes to service the

installations with respect to the environment and has chosen to integrate the environmental performance in the whole

lifecycle of its products, throughout manufacturing, release, use and disposal.

Batteries and rechargeable batteries

If your product contains batteries or rechargeable batteries, these shall be disposed of at the designated

collecting centers.

The product

Users in the EU, Switzerland and Norway

Our Products contain high quality components and are designed to facilitate recycling.

Our products or product packaging are marked with the symbol below.

The symbol indicates that the product must not be treated as municipal waste. It must be disposed of

separately via the appropriate return and collection systems available. By following these instructions you

ensure that this product is treated correctly and help to reduce potential impacts on the environment and

human health, which could otherwise result from inappropriate handling. Recycling of products helps to

conserve natural resources and protect the environment.

For more detailed information on collection and recycling systems for this product, please contact the shop

where you purchased it, your local dealer or sales/service representatives.

All Other Users

If you wish to discard this product, please contact your local authorities, the shop where you bought this

product, your local dealer or sales/service representatives.

SP 1000SF

- 7 -

1 - Security - Certification - Environment - Licence

Software use license

CAREFULLY READ ALL THE TERMS AND CONDITIONS OF THE PRESENT LICENSE BEFORE OPENING THE

SEALED ENVELOPE CONTAINING THE SOFTWARE. OPENING THIS ENVELOPE INDICATES THAT YOU

ACCEPT THESE TERMS AND CONDITIONS.

In case you should not accept the terms of this license, the CD-ROM packaging should be returned to the retailer

unopened, along with the other components of the product.

Definition

The Software designates programs and associated documentation.

License

- This license allows you to use this Software on personal computers on a local network. You only have permission to

use this Software to print on one multifunction machine; you can not lend the Software or authorize anyone to use it.

- You are allowed to make a back up copy.

- This license is non-exclusive and non-transferable.

Property

The manufacturer or its providers hold the Software property right. You only become the owner of the CD-ROM. You

shall not modify, adapt, decompile, translate, create any derived piece, rent or sell the Software or the documentation.

Any rights not explicitly approved are reserved by the manufacturer or its providers.

Duration

This license remains valid until cancelled. You can cancel it by destroying the program and the documentation as well

as any other copies of them. This license will automatically be canceled in case you do not respect the terms of this

license. If the license is rendered invalid, you agree to destroy all copies of the program and the associate

documentation.

Warranty

The Software is provided "as is" with no warranties what so ever, whether expressed or implied, including without

limitation, any warranties of merchantability or fitness for a particular purpose; all the risks concerning the results and

performance of this Software are assumed by the buyer. In case the program should appear defective, all the repair

and service expenses will be covered by the buyer.

Nevertheless, the license holder benefits from the following warranty: we guarantee that the CD-ROM on which the

Software is recorded is free from hardware or manufacturing faults if used in normal conditions, the guarantee is valid

for ninety (90) days from the delivery date, the copy of the receipt being the proof of purchase. In case of a CD-ROM

fault that due to accident or misuse, the CD-ROM will not be replaced as per the warranty.

Responsibility

If the CD-ROM is not working properly, send it to the retailer together with a copy of the receipt. It is the retailer's sole

responsibility to replace the CD-ROM. Nobody, not even the manufacturer who is involved in the creation, realization,

merchantability and delivery of this program would be responsible for direct, indirect or immaterial damages, such as,

but not limited to, loss of information, loss of time, execution loss, loss of revenue, loss of customers, due to the use or

inability to use the program.

Development

With a constant concern for improvement, the manufacturer reserves the right to modify the Software specifications

without any notice. In case of modification, your user right does not give you access to free updates.

SP 1000SF

- 8 -

1 - Security - Certification - Environment - Licence

Registered trademarks

Companion Suite Pro is a registered trademark of Sagem Communication.

Adobe® and the Adobe® products referred to here are registered trademarks of Adobe Systems Incorporated.

PaperPort9SE is a registered trademark of ScanSoft.

Microsoft® Windows® 98, Microsoft® Windows® Millennium®, Microsoft® Windows NT®, Microsoft® Windows

2000®, Microsoft® Windows XP®, and any other Microsoft® product referred to here are registered trademarks of

Microsoft Corporation registered and/or used in the United States and/or in other countries.

All the other brands or products referred to as examples or in order to give additional information are registered

trademarks of their respective owners.

The screenshots presented in this operating instructions have been created with Windows XP. If you use another

operating system, the screenshots displayed may be different from the ones presented in this booklet.

Notice

Do not copy or print any item for which reproduction is prohibited by law.

Copying or printing the following items is generally prohibited by local law: bank notes, revenue stamps, bonds, stock

certificates, bank drafts, checks, passports, driver's licenses.

The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its completeness or

accuracy.

If you have any questions concerning the legality of copying or printing certain items, consult with your legal advisor.

SP 1000SF

- 9 -

2 - Installation

Installation

Location conditions

By choosing an appropriate location, you preserve the longevity of the machine. Check that the selected location has

the following characteristics:

- Choose a well ventilated location.

- Make sure not to obstruct the ventilation grids located on the left and right sides of the device. During the

installation, make sure to place the machine thirty centimeters away from the surrounding objects so all the lids

can be easily opened.

- Make sure that this location does not present any ammonia nor any other organic gasses emission hazard.

- The ground outlet (refer to the security notices presented in the Security chapter) to which you plan to connect

the machine shall be located close to this one and have an easy access.

- Make sure that the machine is not directly exposed to sun light.

- Make sure not to place the machine in an area exposed to an air flow generated by an air conditioning, heating or

ventilation system, nor in an area subject to big temperature or humidity jumps.

- Choose a solid and horizontal surface on which the machine will not be exposed to intense vibrations.

- Keep the machine away from any object that could obstruct its ventilation ports.

- Do not place the machine close to hangings or any other flammable objects.

- Choose a location where the water and other splashes of liquid are limited.

- Make sure that this location is dry, clean and dust free.

Cautions of use

Take into account the important precautions below when using the machine.

Running environment:

- Temperature : 10 °C to 27 °C with an ambient humidity included between 15 to 80% (up to 32°C with an ambient

humidity included between 15 to 54%).

Terminal:

The section below describes the precautions to be taken when using the machine:

- Never turn the machine off and never open the lids while printing.

- Never use gas or flammable liquids, or objects generating magnetic field close to the machine.

- When you unplug the power cord, always hold the connector without pulling the cord. A damaged cord presents

a potential fire hazard or an electric shock hazard.

- Never touch the power cord with wet hands. You risk getting an electric shock.

- Always unplug the power cord before moving the machine. Otherwise, you could risk having the cord damaged

and create a fire hazard or an electric shock hazard.

- Always unplug the power cord when you plan not to use the machine for a long period of time.

- Never put objects on the power cord, never pull it and never fold it. This could cause a fire hazard or an electric

shock hazard.

- Always make sure that the machine is not sitting on the power cord or any other electric device communication

cables. Make sure also that neither cord nor cable is introduced to the machine inner mechanism. This would

expose you to a machine malfunction risk or to a fire hazard.

- Make sure that the printer is unplugged from the power outlet before connecting or disconnecting an interface

cable to the printer (use a shielded interface cable).

- Never try to remove any fixed pane or hood. The machine contains high voltage circuits. Any contact with these

circuits can cause an electric shock risk.

- Never try to modify the machine. This could cause a fire hazard or an electric shock hazard.

- Always make sure that paper clips, staples or other small metallic items do not get inside the machine via the

ventilation ports or other ports. Such items create fire hazards or electric shock hazards.

- Prevent water and any other liquid from spilling on the machine or near to it. Any contact of the machine with water

or liquid can cause a fire hazard or an electric shock hazard.

SP 1000SF

- 10 -

2 - Installation

- If liquid or metallic item gets accidentally inside the machine, turn it off immediately, unplug the power cord and

contact your retailer. Otherwise, you would face a fire hazard or an electric shock hazard.

- In case of heat, smoke, unusual smell or abnormal noise emissions, turn the machine off, unplug the power cord

immediately and contact your retailer. Otherwise, you would face a fire hazard or an electric shock hazard.

- Avoid using the machine during an "electric storm", this can cause an electric shock hazard due to lightning.

Paper for printing: if you use paper already printed by your machine or another printer, the printing quality may not be

optimal.

Safety information

When using your product, the following safety precautions should always be followed.

Safety During Operation

In this information slip, the following important symbols are used:

WARNING

- Connect the power cord directly into a wall outlet and never use an extension cord.

- Disconnect the power plug (by pulling the plug, not the cable) if the power cable or plug becomes frayed or

otherwise damaged.

- To avoid hazardous electric shock or laser radiation exposure, do not remove any covers or screws other than

those specified in the Operating Instructions.

- Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any of the following

conditions exists:

• You spill something into the product.

• You suspect that your product needs service or repair.

• Your product’s cover has been damaged.

- Do not incinerate spilled toner or used toner. Toner dust might ignite when exposed to an open flame.

- Disposal can take place at our authorized dealer or at appropriate collection sites.

- Dispose of the used toner cartridge (or bottle) in accordance with the local regulation.

CAUTION

- Protect the product from dampness or wet weather, such as rain, snow, and so on.

- Unplug the power cord from the wall outlet before you move the product. While moving the product, you should

take care that the power cord will not be damaged under the product.

- When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).

- Do not allow paper clips, staples, or other small metallic objects to fall inside the product.

- Keep toner (used or unused), toner cartridge (or bottle), ink (used or unused) or ink cartridge out of reach of

children.

- Be careful not to cut yourself on any sharp edges when you reach inside the product to remove misfed sheets of

paper or masters.

CAUTION

Make sure to place the machine in well ventilated premises. When operating, the printer generates

a small amount of ozone. An unpleasant smell can come from the printer if it is used intensively in

not well ventilated premises. For a secure use, make sure you place the machine in well ventilated

premises.

WARNING:

Indicates a potentially hazardous situation which, if instructions are not followed, could result in

death or serious injury.

CAUTION:

Indicates a potentially hazardous situation which, if instructions are not followed, may result in

minor or moderate injury or damage to property.

SP 1000SF

- 11 -

2 - Installation

- For environmental reasons, do not dispose of the product or expended supply wastes at household waste

collection point. Disposal can take place at our authorized dealer or at appropriate collection sites.

- Our products are engineered to meet the high standards of quality and functionality, and we recommend that you

only use the expendable supplies available at an authorized dealer.

Power Supply

The socket-outlet shall be installed near the product and shall be easily accessible.

For Fax or Telephone

- Do not use this product near water, for example near bath tub, wash bowl, kitchen sink or laundry tub, in a wet

basement or near a swimming pool.

- Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of an

electric shock from lightning.

- Do not use a telephone in the vicinity of a gas leak to report the leak.

Rules for use symbols

WARNING

Indicates important safety notes.

Ignoring these notes could result in serious injury or death. Be sure to read these notes. They can be found in the

“Safety Information” section of this manual.

CAUTION

Indicates important safety notes.

Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read

these notes. They can be found in the “Safety Information” section of this manual.

Important

Indicates points to pay attention to when using the machine, and explanations

of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure to read these explanations.

Note

Indicates supplementary explanations of the machine's functions, and instructions on resolving user errors.

SP 1000SF

- 12 -

2 - Installation

Terminal description

Front side

Back side

Document feeder

Command panel

Paper output

Paper tray

Master USB

Manual paper feed

setup guides

(USB key)

Smart card

insertion point

Fold-down

stopper for

paper delivery

connection

Manual

input tray

Front cover

Slave USB connection

(for PC)

Power supply cord

connection

Paper jam cover

EXT. socket - connection

for external devices

LINE socket - telephone

cable connection

Master USB connection

(USB key)

On/Off switch

Can be used for same function as USB connection on front side.

SP 1000SF

- 13 -

2 - Installation

Command panel

Presentation

Entering Characters Using the Alpanumerical keypad

As you perform various tasks, you need to enter names and numbers. For example, when you set up your machine,

you enter your name (or your company’s name) and telephone number. When you store one-, two-, or three-digit speed

dial or group dial numbers, you may also enter the corresponding names.

To enter alphanumeric characters when you are prompted to enter a letter, locate the button labeled with the character

you want. Press the button until the correct letter appears on the display.

Examples :

- to enter the name "John", press : 1 time, 6 times, 5 times and 5 times.

- to enter "!", press : 17 times.

If you make a mistake while entering a number or name, press the C button to delete the last digit or character. Then

enter the correct number or character.

5711121314151617

810

1. Screen.

2. Alphanumerical keypad.

3. One-Touch keypad (buttons 1 to 20).

4. Button : document analysis to the PC or a

media (USB key).

5. Button : local copy.

6. Button : stops the current PC printing.

7. Button : sending a fax.

8. Button :

access to directory and quick dial

numbers.

9. Button

line manual connection, listen for tone

during fax sending.

10. Button :

multiple contact sending (fax).

11. Button : Validation.

12. Button OK: confirms the displayed selection.

13. Button : menu access and navigation down the

menus.

14. Button C: back to the previous menu and input

correction.

15. Button : navigation up the menus.

16. Button : stops the current operation.

17. Button ECO: sets up the activation delay.

18. Button : colour analysis mode selection.

19. Button : analysis resolution setup.

20. Button : contrast setup.

21. Icon :

resolution

"Copy

Quality text

/ Fax

Sfine

22. Icon : resolution "

Photo

23. Icon : resolution "Copy :

Auto

/ Fax :

Fine

24. Icon : color mode.

25. Icon : activity on the telephone line.

26. Icon : Fax mode.

27. Icon : external answering device mode

SP 1000SF

- 14 -

2 - Installation

The following table gives all available characters.

Accessing terminal functions

All terminal functions and settings are available via the menu and are associated to a specific menu command. For

example, C

ONTRAST copy settings are identified in the menu with the command 845.

Two methods are available to access menu items : a step by step method or a shortcut method.

To access the C

ONTRAST settings with the Step by step method :

1 Press on  to access the menu.

2 Use the  or  buttons to browse the menu and select 8-A

DVANCED FCT. Confirm with OK.

3 Use the  or  buttons to browse the A

DVANCED FUNCTIONS menu and select 84-COPY. Confirm with OK.

4 Use the  or  buttons to browse the C

OPY menu and select 845-CONTRAST. Confirm with OK.

To access the C

ONTRAST settings with the shortcut method :

1 Press on  to access the menu.

2 Enter 845 with the alphanumerical keypad to directly access the C

ONTRAST item.

Key Assigned numbers, letters, or characters Key Assigned numbers, letters, or characters

1 P, Q, R, S, p, q, r, s, 7

A, B, C, a, b, c, 2 T, U, V, t, u, v, 8

D, E, F, d, e, f, 3 W, X, Y, Z, w, x, y, z, 9

G, H, I, g, h, I, 4 Space 0 @ . + - / & $ %

J, K, L, j, k, l, 5

# _ , ; : ? ( ) [ ] < > { } ~ = ! ' " \ |

€

M, N, O, m, n, o, 6 *

SP 1000SF

- 15 -

2 - Installation

Packaging contents

The packaging contains the items listed below:

Multifunction device

1 toner cartridge

1 installation guide and 1 PC installation CD ROM

1 Safety Guide, Command Guide (For Europe and

North America only)

1 power cord

1 telephone cord (Only North America,China,Korea)

1 USB cord

Device installation

1 Unpack the device.

2 Install the device respecting the security notices

stated at the beginning of this booklet.

3 Remove all stickers from the machine.

4 Remove the plastic protection film from the screen.

Installing the document feeder

1 Secure the document feeder by fitting the two clips

(B) in the notches (A) provided for this purpose.

Loading paper

Loading paper in the paper tray

(1) Paper to be used must be inserted face down, and

abutting the side fence and back fence. Not abutting

the paper may cause feed failure, skewing or paper

jams.

(2) Amount of loaded paper must not exceed the loading

mark. If the loading mark is exceeded, this may cause

feed failure, skewing, or paper jams.

(3) Adding paper to the pile may cause double feeding,

and should be avoided.

(4) When withdrawing the cassette from the main unit,

always hold it with both hands.

Handling of paper

(1) Curling must be corrected before loading.

(2) Curls must not exceed 10 mm.

(3) Care must be taken with storage to prevent feed faults

and image defects due to leaving the paper in

conditions of high humidity.

Adding paper to the pile, or splitting the pile may cause

feeding problems, and must be avoided.

Humidity control

(1) Paper which has become damp, or paper which has

been left unused for a very long time, must not be

used.

(2) After opening the paper, it must be kept in a plastic

bag.

SP 1000SF

- 16 -

2 - Installation

(3) Paper with waved ends, paper which is creased, paper

with crumples, and any other non-normal paper must

not be used.

Handling the unit

Operator shocks

During printing, shocks must not be applied to the paper

feed cassette, tray, cover, and other parts of the machine.

Moving the unit

When moving the unit on a desk, it must be lifted, and not

dragged.

Handling the Toner Cartridge

(1) Must not be stood on the side, or held upside down.

(2) Must not be shaken strongly.

Feed cassette paper insertion

Your device accepts a number of formats and types of

papers.

1 Remove the paper feed cassette completely.

2 Push the lower panel down until it clicks.

3 Setup the back side feed cassette stop by pushing

the "PUSH" lever (A).

Then adjust the lateral paper guides to the paper

format by pushing lever (B) located on the left

guide. Adjust the length paper guide to the paper

format by pushing lever (C).

4 Take a paper stack, pull the paper off and align it

on a flat surface.

5 Put the paper stack in the feed cassette

(200 sheets for 80 g/m² paper for instance).

6 Put the feed cassette back in its location.

Cartridge installation

1 Stand in front of the machine.

2 Push the left and right sides of the cover and pull it

at the same time towards you.

3 Remove the starter toner cartridge from its bag.

Gently roll the cartridge 5 or 6 times to distribute the

toner evenly inside the cartridge.

Thoroughly rolling the cartridge will assure the

maximum copies per cartridge.

Important

See chapter Specifications for the

various formats and types of paper.

PUSH

7¼5½

SP 1000SF

- 17 -

2 - Installation

4 Hold it by its handle.

5 Insert the cartridge in its slot by pushing it until it

clicks (last move down) as shown on the picture

below.

6 Close the cover.

Paper delivery stop

Adjust the paper delivery stop, depending on the format of

the document to be printed. Do not forget to raise the flap

to prevent the sheets from falling down.

Starting your device

Device connection

1 Plug the end of the telephone line into the terminal

socket and the other end into the wall telephone

socket.

2 Connect the power cord to the device.

3 Make sure that the On/Off switch is off (O position).

Plug the power cord to outlet on the wall.

4 Press the On/Off button to turn on the device

(I position).

5 By default, the machine is set to operate in England

and in English. To modify this parameter, refer to

Country, page 26.

6 Set the date and time, refer to Date/Time, page 26.

WARNING

Before plugging the power cord, it is

imperative to refer to the Security

directives, page 1.

WARNING

The power cord is used as a 230 V

power unit cut off. As a precaution,

the outlet shall be located close to

the device and be of easy access in

case of danger.

Page is loading ...

Ricoh Aficio SP 1000SF User manual

Ricoh Aficio SP 1000SF User manual

This manual is also suitable for

Ricoh Aficio SP 1000SF User manual

Related papers

Other documents