ATD Tools Atd-7328 Owner's manual

Brand
ATD Tools
Model
Atd-7328
Category
Motor vehicle accessories & components
Type
Owner's manual
The safety alert symbol is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible injury or property damage.
!
ATD7328_rev_0119
Capacity: 22 Tons
ATD-7328
Owner’s Manual
Visit us at www.atdtools.com
Features:
Low pickup height and maximum lift height
Large steel wheels for easy positioning
Sturdy, one-piece handle
Self-returning spring for ease and convenience
0LQLPXP+HLJKWƎ
0D[LPXP+HLJKWƎZLWKDGDSWHU
([WHQVLRQ6FUHZƎ
+DQGOH/HQJWKƎ
6L]HƎL[Ǝ:
Hydraulic Range: 4-5/8”
Shipping :eight: 97 lbs.
Read this manual and follow all Safety Rules and Operating Instructions before using this product.
22-Ton Low Profile Axle Jack
2
SAFETY AND GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this device
before using. The owner and/or operator shall have an understanding of the device, its operating characteristics and
safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use and
repair of this product may require special skills and knowledge. Instructions and safety information shall be read to
and discussed with the operator in the operator's native language, making sure that the operator comprehends their
contents, before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this device,
remove from service immediately.
Inspect before each use. Do not use if abnormal conditions such as cracked welds, damaged, loose or missing parts
are noted. Any equipment that appears damaged in any way, is found to be worn, or operates abnormally shall be
removed from service until repaired. If the equipment has been or is suspected to have been subjected to an abnormal
load or shock, immediately discontinue use until inspected by a factory authorized repair facility FRQWDFW distributor
or manufacturer for list of authorized repair IDFLOLWLHV It is recommended that an annual
inspection be made by an
authorized repair facility. Labels and Operator's Manuals are available from the manufacturer.
PRODUCT DESCRIPTION
Hydraulic Axle Jacks are designed to lift, but not support, rated capacity partial vehicle loads consisting of
one end of a vehicle. Immediately after lifting, support loads with a pair of appropriately rated jack stands.
PREPARATION
Reference replacement parts pages 6 and 7 for parts location & assembly sequence. Assemble, align and insert the
handle assembly and handle position bar into the handle sleeve, then tighten the bolt on handle sleeve to prevent
accidental removal of handle while in use.
Before Use
1.
Verify that the product and application are compatible, if in doubt call ATD Tools, Inc. Technical Service at 888-332-6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. TRIDPLOLDUL]H\RXUVHOIZLWKEDVLFRSHUDWLRQORFDWHDQGWXUQWKHUHOHDVHYDOYHKDQGOHNQRE
a. Clockwise
CLOSED’ release valve position used to raise
the load.
b. Counter-clockwise, no more than 1 full turn from closed position. This is the ‘OPEN’ release valve position used
to lower the load. The further the release valve is turned counter-clockwise, the faster the load descends.
5. Pour a teaspoon of good quality air tool lubricant into the air supply inlet of the lift control valve. Connect to air supply,
then squeeze the lift control valve for 3 seconds to evenly distribute lubricant.
NOTICE:
tape or compound is used on connections. To ensure dependable, trouble free operation an inline air dryer and oiler
is recommended.
6. Ensure that jack rolls freely. Raise and lower the unloaded ram throughout the lifting range before putting into
service to ensure the jack operates smoothly. Replace worn or damaged parts and assemblies with ATD Tools, Inc.
authorized replacement parts only.
Bleeding/Venting Trapped Air
2. Open release valve.
3. Activate air motor to vent air.
4. Remove set screw and use a screw driver to hold down check ball while, very slowly pumping air motor until oil
exiting from screw hole is steady without bubbles.
5HLQVWDOOVHWVFUHZDSSUR[LPDWHO\WZRWXUQVLQWRKROHGRQRWIXOO\WLJKWHQ
6. Activate air motor a few additional times to vent air, while slowly tightening set screw. Ram should start to raise as
screw is fully tightened.
3
Figure 1 - Typical Truck Jack Nomenclature
Handle Knob
(release valve)
Saddle
Carrying
Handle
Oil Filler
Screw
:KHHO
Handle Sleeve
Handle Position
Release
Air Supply Inlet,
1/4 NPT
Lift Control
Valve
Handle
Extension Screw
Adapter Holder
Adapter, 2-1/2"
SPECIFICATIONS
Model Capacity Jack Size (L x W)
Min.
Height
Max.
Height
Hyd.
Range
Extension
Screw
ATD-7328 22 Ton 22-7/8" x 12-1/2" 8-1/4" 22" 4-5/8" 3-7/8"
(With adapter)
4
!
WARNING: Be sure all tools and personnel are clear before
lowering load. Slowly open the release valve!
The more you turn the handle knob counter-clockwise, the faster the load will come down. Maintain
control of the rate of speed at which the load lowers at all times!
1. Raise load high enough to clear the jack stands.
2.
5HPRYHMDFNVWDQGVFDUHIXOO\always used in pairs).
3. Slowly turn handle knob counter-clockwise, but no more than 1 full turn and slowly lower the load.
4. After removing jack from under the vehicle, fully retract the jack to reduce ram exposure to rust and contamination.
!
!
To avoid crushing and related injuries:

Never work on, under or around a load supported
only by hydraulic jack.

Always use adequately rated jack stands.
&KRFNHDFKXQOLIWHGWLUHLQERWKGLUHFWLRQV
Do not use this device to lift, level, lower, support or
move a house, mobile home, travel trailer, camper or
any building structure.
Be alert and sober when using this product. Do not
X
!
The wheels provided with this jack are for positioning the jack under a load ONLY! The wheels are
not load wheels. Do not try to dolly or move the vehicle with the jack!
OPERATION VHH)LJ
Lifting
Note: The jack is equipped with handle position lock. To adjust the handle, release lock device by pulling the lever
up, lever is spring loaded and will lock into desired position. Ensure lever locking mechanism is fully engaged before
lifting.
1. Connect adequate air source to the air supply inlet.
2. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock
each unlifted wheel in both directions to prevent inadvertent vehicle movement.
3.
Close the release valve by turning the handle knob clockwise un
4. Center jack saddle under lift point, then squeeze the lift control valve until saddle contacts the lift point. To lift,
continue squeezing the lift control valve until load reaches desired height. Simply release your grip on the lift
control valve to end lift event.
5. Transfer the load immediately to appropriately rated jack stands.
WARNING: Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only
WARNING: NEVER use hydraulic jack as a stand alone
device! ALWAYS transfer the lifted load
IMMEDIATELY to a pair of appropriately rated jack stands. Use one pair of jack stands per vehicle.
Rated capacity is per pair only! Do not exceed rated capacity.
Lowering
6WXGy, understand, and follow all
instructions
before operating this device.
'RQRWH[FHHGUDWHGFDSDFLWy.
8VHRQO\RQKDUGOHYHOVXUIDFH
/LIWLQJGHYLFHRQOy. Immediately after lifting,
support the vehicle with appropriate means.
'RQRWPRYHRUGROO\WKHYHKLFOHZKLOHRQWKH
jack.
the vehicle manufacturer.
1RDOWHUDWLRQVVKDOOEHPDGHWRWKLVSURGXFW
)DLOXUHWRKHHGWKHVHPDUNLQJVPD\UHVXOWLQ
personal injury and/or property damage.
WARNING WARNING
5
MAINTENANCE
Important:
potential for sudden and immediate loss of load. :e recommend premium hydraulic oil or equivalent.
Adding/ Changing Oil
d supply at least once per year.
screw.
r.
NOTICE:
l regulations.
3. Set jack in its upright, level position.
4. Fill with oil. Proper oil level is just below the rim of the
5. Perform Bleeding/Venting Trapped Air SURFHGXUHSDJH
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that
wheels move freely and the pump functions smoothly. To help ensure trouble free operation, an inline air dryer and
oiler is recommended.
Cleaning
Periodically check the ram for signs of rust or corrosion. Clean as needed and wipe with an oily cloth.
Note: Never use sandpaper or abrasive material on ram surfaces!
Storage
:KHQQRWLQXVHVWRUHWKHMDFNZLWKVDGGOHIXOO\ORZHUHG
TROUBLESHOOTING
Symptom Possible Causes Corrective Action
Jack will not lift load
5HOHDVHYDOYHQRWWLJKWO\FORVHG
/RDGLVWRRKHDY\
Air supply inadequate
(QVXUHUHOHDVHYDOYHWLJKWO\FORVHG
&RQVLGHUKLJKHUFDSDFLW\MDFN
(QVXUHDGHTXDWHDLUVXSSO\
Jack will lift, but not maintain
pressure
Release valve not tightly closed
+\GUDXOLFXQLWPDOIXQFWLRQ
Ensure release valve tightly closed
'LVFRQWLQXHXVHFRQWDFW$7'7RROV
Technical Service at 888-332-6419.
Jack will not lower after unloading
/LQNDJHVELQGLQJ &OHDQDQGOXEULFDWHPRYLQJSDUWV
Poor lift performance )OXLGOHYHOORZ
Air trapped in system
Follow Bleeding/Venting Trapped
Air procedure on page 2
:LOOQRWOLIWWRIXOOH[WHQVLRQ )OXLGOHYHOORZ
REPLACEMENT PARTS
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. :KHQ ordering parts, please give the Model number, part number and parts
description.
6
Figure 2 - Replacement Parts Illustration for Model ATD-7328
Item Part No. Description Qty
1 A09-4-2200-106 Handle Assembly 1
2 506-9-0280-104 Handle Grip 2
3 421-6-2202-209 Knob 1
4 601-4-0040-034 Spring Pin 1
5 653-1-0100-308 Bolt 1
6 605-3-0100-203 :asher, Lock 5
7 A09-6-1301-109 Handle Sleeve 1
8 A09-6-3221-101 Cover Plate 1
9 609-1-0050-10911 Screw 4
10 A09-4-3400-109 :KHHO 2
11 511-3-0130-010 :asher 2
12 667-5-0127-005 C-clip 2
13 G53-3-2000-205 Air Motor 1
14 653-1-0100-106 Bolt 4
15 515-3-0140-103 Copper Gasket 1
16 A22-4-2040-107 Air Hose Assembly 1
17 507-9-0064-013 Air Hose 1
18 A27-3-2050-109 Lift Control Valve 1
19 A24-6-8101-107
Air Coupler, Male,
1/4 NPT
1
20 A07-3-3300-307 Release Valve Cable 1
Item Part No. Description Qty
21 A09-5-1701-105 Release Valve 1
22 554-7-0062-007 Oil Seal 1
23 649-1-0050-019 Screw 1
24 653-1-0080-02511 Screw 2
25 661-2-0080-023 Nut 2
26 324-4-1900-208
Filler Screw
1
27 523-2-0196-016 Spring 4
28 A07-5-1101-101 Extension Screw 1
29 A07-5-1108-105 Saddle 1
30 A07-5-1802-101 Spring Plate 1
31 A07-4-2900-100
Air Filter
1
32 A09-3-9901-206
Repair Kit
(includes
#15, #22 & A~K)
-
33 A27-3-2200-102 Piston, Air Motor #13 1
34 A09-1-1005-105
+\GUDXOLF8QLWdoes
127LQFOXGH
DQG
1
35
A09-6-3230-102
:KHHO Axle 2
36 A09-6-3124-104 Base Plate 1
37 A09-6-1104-107 Adapter Holder 1
38 A07-6-1109-103 Adapter, 2-1/2" 1
B
B
38
1
6
37
24
8
5
6
2
5
4
3
2
36
9
14
6
2
3
2
0
1
3
1
5
35
1
0
1
2
E
2
2
2
1
3
4
D
F
2
7
C
A
B
2
9
30
2
8
7
1
8
31
1
9
1
7
33
2
6
G
H
J
K
I
Replacement Parts for model ATD-7328:
7
WARRANTY
1 YEAR LIMITED WARRANTY
THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
PURCHASED FROM: _______________________________________
DATE PURCHASED: ________________________________________
INVOICE/RECEIPT NUMBER: _________________________________________
[Affix receipt or invoice here for safe keeping]
Your ATD-7328 is warranted for a period of 12 months from the original purchase date.
)RUDSHULRGRIRQH\HDUIURP\RXUSXUFKDVHGDWH ATD TRROV,QFZLOOUHSDLURUUHSODFHDWLWVRSWLRQZLWKRXWFKDUJH\RXU ATD
product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced dur-
ing normal use of the product. This limited warranty is your exclusive remedy.
under warranty, freight prepaid, to your supplier for warranty determination.
be void. :e are not responsible for damage to ornamental designs you place on this ATD product and such ornamentation should
not cover any warnings or instructions or they may void the war
It also does not cover normal wear items such as but not limited to
brushes, batteries, drill bits, drill chucks, pads or blades.
Subject to the law in your state:
 Your sole and exclusive remedy is repair or replacement of the defective product as described above.
 The repair and replacement of this product under the express limited warranty described above is your exclusive remedy and
is provided in lieu of all other warranties, express or implied. All other warranties, including implied warranties and warranties of
ed and, if disclaimer is prohibited, these warranties are limited to one
year from your date of purchase of this product.
Some states’ laws do not allow limited durations on certain implied warranties and some states’ laws do not allow limitations on
incidental or consequential damages. You should consult the law in your state to determine how your rights may vary.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

ATD Tools Atd-7328 Owner's manual

Brand
ATD Tools
Model
Atd-7328
Category
Motor vehicle accessories & components
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents