Keystone Visage Installation Instructions Manual

Brand: Keystone

Model: Visage

Type: Installation Instructions Manual

GRILL STATION

INSTALLATION INSTRUCTIONS

2 Keystone Step-by-StepKits

VISAGE GRILL STATION

Outdoor Grill Station Kit Placement

Outdoor grill station kit may be placed directly on a

stable patio surface or be supported by a concrete

or crushed stone leveling pad below grade. Below

grade leveling pad shown here. Adjust height as

desired.

Note: See foundation layout details sheet for further

foundation information.

Safety

Glasses

BASIC TOOLS

safety alterations finishing leveling general

Gloves Mallet Caulking

Gun

Concrete

Adhesive

Level Mallet Shovel Wheelbarrow Hand

Compactor

You will need:

55 - Visage - 16"/12"unit

57 - Visage - 16"/14"unit

10 - Tubes exterior grade concrete adhesive

Crushed Aggregate - 15.28 cf

Built-in Grill*

(31"w x 21"d x 10"h rough opening)

Access Door* (15¾"w x 19½"h rough opening)

Lower Counter Material - 91¼" x 25½"

Upper Counter Material - 91¼" x 16"

Steel Lintel (shown)*

(6"wide x 41"long x

⁄16"thick)

Note: All units are 6"h x 8"d.

*Modify rough opening sizes in both the block units

and counter top to accommodate different sized

appliances, if needed.

Concrete Saw

Wheel Grinder

Keystone Step-by-StepKits 3

www.KeystoneRetailProducts.com

VISAGE GRILL STATION

www.KeystoneRetailProducts.com

General Note:

In consideration of freeze / thaw issues

during the cold weather season it is

recommended that this outdoor built-in

grill station element be protected from

rain, snow and ice as necessary.

4 Keystone Step-by-StepKits

VISAGE GRILL STATION

Keystone Step-by-StepKits 5

www.KeystoneRetailProducts.com

COURSE BY COURSE INSTRUCTIONS

On Grade Installation Note:

If the grill station is to be built on top of a stable

patio or hardscape surface, eliminate the 1st

course and base leveling pad from the grill

station design.

Appliance Service Note:

Plan and install gas and other desired utilities

prior to and during construction as needed.

6 Keystone Step-by-Step Kits

COURSE BY COURSE INSTRUCTIONS

On Grade Installation Note:

If the grill station is to be built on top of a stable

patio or hardscape surface, eliminate the 1st

course and base leveling pad from the grill

station design.

Keystone Step-by-Step Kits 7

www.keystonewalls.com

COURSE BY COURSE INSTRUCTIONS

8 Keystone Step-by-Step Kits

COURSE BY COURSE INSTRUCTIONS

Block Cutting Note:

Using a concrete saw or wheel grinder tool w/

masonry disk, cut block units as needed. Block

units to be cut due to obstruction are labeled

with solid hatching. Block units to be cut to ﬁt are

labeled with angular hatching.

Block Cutting for Appliances Note:

See appliance manufacturer’s installation

instructions for correct block cutting to allow for

proper ﬁt for appliances.

Keystone Step-by-Step Kits 9

www.keystonewalls.com

COURSE BY COURSE INSTRUCTIONS

Block Cutting Note:

Using a concrete saw or wheel grinder tool w/

masonry disk, cut block units as needed. Block

units to be cut due to obstruction are labeled

with solid hatching. Block units to be cut to ﬁt are

labeled with angular hatching.

Block Cutting for Appliances Note:

See appliance manufacturer’s installation

instructions for correct block cutting to allow for

proper ﬁt for appliances.

10 Keystone Step-by-Step Kits

COURSE BY COURSE INSTRUCTIONS

Block Cutting Note:

Using a concrete saw or wheel grinder tool w/

masonry disk, cut block units as needed. Block

units to be cut due to obstruction are labeled

with solid hatching. Block units to be cut to ﬁt are

labeled with angular hatching.

Block Cutting for Appliances Note:

See appliance manufacturer’s installation

instructions for correct block cutting to allow for

proper ﬁt for appliances.

Keystone Step-by-Step Kits 11

www.keystonewalls.com

COURSE BY COURSE INSTRUCTIONS

Block Cutting Note:

Using a concrete saw or wheel grinder tool w/

masonry disk, cut block units as needed. Block

units to be cut due to obstruction are labeled

with solid hatching. Block units to be cut to ﬁt are

labeled with angular hatching.

Block Cutting for Appliances Note:

See appliance manufacturer’s installation

instructions for correct block cutting to allow for

proper ﬁt for appliances.

12 Keystone Step-by-Step Kits

COURSE BY COURSE INSTRUCTIONS

Block Cutting Note:

Using a concrete saw or wheel grinder tool w/

masonry disk, cut block units as needed. Block

units to be cut due to obstruction are labeled

with solid hatching. Block units to be cut to ﬁt are

labeled with angular hatching.

Block Cutting for Appliances Note:

See appliance manufacturer’s installation

instructions for correct block cutting to allow for

proper ﬁt for appliances.

Keystone Step-by-Step Kits 13

www.keystonewalls.com

COURSE BY COURSE INSTRUCTIONS

Block Steel Lintel Cutting Note:

Prior to installing steel lintel, use a wheel grinding

tool to notch out top of block creating a level

shelf to place steel lintel, such that lintel is ﬂush

with top of cut block. Block units to be cut for

steel lintel are shown with solid hatching.

14 Keystone Step-by-Step Kits

COURSE BY COURSE INSTRUCTIONS

Counter Top Cutting for Appliances Note:

See appliance manufacturer’s installation

instructions for correct counter top opening sizes.

Cut to allow for proper ﬁt for applicances. Unless

otherwise directed, use a concrete saw or wheel

grinder tool w/masonry disk to cut the counter

top as needed.

Counter Top Installation Note:

Depending on the type of counter top material

used, the counter top may be installed in multiple

pieces as needed. Joints shown with dashed lines

are suggested locations only.

Unless otherwise directed, install and secure

counter top material with a polyurethane

masonry adhesive or approved equal as per

manufacturer’s intallation instructions.

Keystone Step-by-Step Kits 15

www.keystonewalls.com

COURSE BY COURSE INSTRUCTIONS

Counter Top Cutting Note:

Unless otherwise directed, use a concrete saw or wheel

grinder tool w/masonry disk to cut the counter top as

needed.

Counter Top Installation Note:

Depending on the type of counter top material used, the

counter top may be installed in multiple pieces as needed.

Joints shown with dashed lines are suggested locations only.

Unless otherwise directed, install and secure counter top

material with a polyurethane masonry adhesive or approved

equal as per manufacturer’s intallation instructions.

Counter Top Support Note:

Provide under counter support as needed depending on

the over hang of the counter and the type of counter top

material used.

Keystone Retaining Wall Systems LLC

A Contech Company

4444 West 78th Street • Minneapolis, MN 55435

(952) 897-1040 • www.keystonewalls.com

We reserve the right to improve our products and make changes in the speciﬁcations and design without

notice. The information contained herein has been compiled by KEYSTONE and to the best of our knowledge,

accurately represents the KEYSTONE product use in the applications which are illustrated. Final determination

of the suitability for the use contemplated and its manner of use are the sole responsibility of the user.

Sbs Visage-Grill Station - 0416

Don’t forget to check out all of our Keystone Outdoor Living designs on keystonewalls.com.

Outdoor Kitchen Designs Fireplaces Columns Fire Pits Water Feature Bench

Keystone Visage Installation Instructions Manual

Keystone Visage Installation Instructions Manual

Keystone Visage Installation Instructions Manual

Related papers

Other documents