Sprite BBC User manual

Brand
Sprite
Model
BBC
Type
User manual

Sprite BBC is a water filtration system designed to be attached to a bathtub spout. It comes with a one-year warranty and is intended for use with potable water systems only. The Sprite BBC is not intended to be used as a drinking water filter.

To install the Sprite BBC, clean and dry the bathtub spout, remove the red tape strip from the back of the harness, center the harness on the spout with the notch under the lip, and press the harness underneath the tape strip. Wrap the tabbed end of the white Velcro strap around the tub spout, hold the strap in place by pressing down on the tab, and secure the other end of the white Velcro strap to the tabbed end. Finish securing the system to the tub spout with the grey harness wrap, securing it in place with the black Velcro ends. Hang the crossbars of the Bath Ball onto the Harness Hooks.

Sprite BBC is a water filtration system designed to be attached to a bathtub spout. It comes with a one-year warranty and is intended for use with potable water systems only. The Sprite BBC is not intended to be used as a drinking water filter.

To install the Sprite BBC, clean and dry the bathtub spout, remove the red tape strip from the back of the harness, center the harness on the spout with the notch under the lip, and press the harness underneath the tape strip. Wrap the tabbed end of the white Velcro strap around the tub spout, hold the strap in place by pressing down on the tab, and secure the other end of the white Velcro strap to the tabbed end. Finish securing the system to the tub spout with the grey harness wrap, securing it in place with the black Velcro ends. Hang the crossbars of the Bath Ball onto the Harness Hooks.

BATH BALL INSTRUCTIONS
INSTALLATION
1. Clean and dry the bath-tub spout.
2. Remove the red tape-strip located at the back of the bath-ball harness.
3. Center the harness, with the notch under the lip, on the bath-tub spout.
4. Press the harness underneath the tape-strip. This will help to secure the system to
the tub-spout.
5. Wrap the tabbed end of the white Velcro strap around the tub-spout. Hold the strap
in place by pressing down on the tab.
6. Secure the other end of the white Velcro strap to the tabbed end. (Note the white
Velcro strap can be adjusted to accommodate the diameter of the spout.)
7. Finish securing the system to the tub-spout with the grey harness wrap, securing it
in place with the black Velcro ends.
8. Hang the cross-bars of the Bath-Ball onto the Harness Hooks.
OPERATION: Run water through Bath Ball.
Avoid overflowing.
CARTRIDGE REPLACEMENT
Replace Cartridge every 6 months or sooner with
model BBC. (Depending on individual water con-
ditions)
1. Remove Cartridge by unscrewing the Bot-
tom of the Bath-Ball Housing.
2. Remove paper seals from each end of the
new cartridge and insert into housing.
3. Screw on the Bottom Housing.
4. Hang Bath-Ball onto Hanger-Hooks.
NOTICE OF LIMITATIONS
The Bath Ball is designed for potable water systems only and NOT to be used as a
drinking water filter.
Visit the Spite Showers website at ww.SpriteShowers.com
Phone: 1-800-327-9137 (U.S. Toll Free)
Image for Installation Steps 2-6
Final Installation Image
←5. Tab
2. & 4.
Red-Tape Strip
6. Velcro →
←3. Notch
Harness Wrap
←
Open Here for
Cartridge Replacement
Harness Hook
→
Limited One Year Warranty to U.S. Customers
Sprite Industries warrants the filter housing only (not the car-
tridge) to be free of defects for a period of one (1) year when
used under normal operating conditions. It is the owner’s re-
sponsibility to keep proof of purchase of the unit and all re-
placement cartridges and to demonstrate that proper cartridge
replacement and filter maintenance was performed as speci-
fied in the owner’s instructions.
The provisions of this warranty shall not apply to any product
that has been submitted to: Abuse, neglect, over-tightening,
lack of or improper periodic filter replacement, repaired or al-
tered by anyone other than an authorized Sprite Industries
service representative, and will VOID the warranty in its entire-
ty.
This is exclusive remedy and liability for consequential damag-
es. There are no other warranties, expressed or implied, lim-
ited to the extent permitted by law.
Return merchandise to Sprite Industries Inc. for repair or re-
placement only, by following these steps:
1. Obtain a Return Merchandise Authorization number
(RMA #) by phoning (800) 327-9137 .
2. Transportation charges on units submitted for repair or
replacement under warranty are to be prepaid and sent
to:
Sprite Industries, Inc
RMA #__________
1791 Railroad St
Corona, CA 92880-2511
3. Please include current return address, telephone num-
ber and a brief description of the problem for pro-
cessing.
4. Enclose in a sealed bag to prevent leakage.
5. Valid proof of purchase must accompany the return.
A. Copy of Sales Receipt.
B. Copy of all cartridge replacements.
  • Page 1 1

Sprite BBC User manual

Brand
Sprite
Model
BBC
Type
User manual

Sprite BBC is a water filtration system designed to be attached to a bathtub spout. It comes with a one-year warranty and is intended for use with potable water systems only. The Sprite BBC is not intended to be used as a drinking water filter.

To install the Sprite BBC, clean and dry the bathtub spout, remove the red tape strip from the back of the harness, center the harness on the spout with the notch under the lip, and press the harness underneath the tape strip. Wrap the tabbed end of the white Velcro strap around the tub spout, hold the strap in place by pressing down on the tab, and secure the other end of the white Velcro strap to the tabbed end. Finish securing the system to the tub spout with the grey harness wrap, securing it in place with the black Velcro ends. Hang the crossbars of the Bath Ball onto the Harness Hooks.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents