Schumacher DSR115 Owner's manual

Brand: Schumacher

Model: DSR115

Category: Battery chargers

Type: Owner's manual

0099001807-02

DSR114

DSR115

MODELS / MODELOS / MODÈLES :

DSR114, DSR115

Jump Starter and DC Power Source

Arrancador y Fuente de Poder de CC

Aide de Démarrage et Source d’Énergie CC

OWNERS MANUAL / MANUAL DEL USUARIO / MANUEL D’UTILISATION

PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE EACH USE.

This manual will explain how to use your jump starter safely and effectively. Please

read and follow these instructions and precautions carefully.

POR FAVOR GUARDE ESTE MANUAL DEL PROPIETARIO Y LEER ANTES DE

CADA USO. En este manual se explica cómo utilizar el arrancador con seguridad

y ecacia. Por favor, lea y siga las siguientes instrucciones y precauciones.

ESSAYER DE GARDER LE MANUEL D’INSTRUCTIONS ET LE LIRE AVANT

CHAQUE UTILISATION. Ce manuel explique comment utiliser l’unité d’une façon

sûre et efcace. S’il vous plaît lisez et suivez ces instructions et précautions.

CONTAINS SEALED, NON-SPILLABLE LEAD-ACID BATTERY.

MUST BE DISPOSED OF PROPERLY.

CONTIENE UNA BATERÍA SELLADA DE ÁCIDO-PLOMO NO

DERRAMABLE QUE DEBE DESECHARSE APROPIADAMENTE.

CONTIENT UNE BATTERIE À L’ACIDE QUI DOIT ÊTREDISPOSÉ

CORRECTEMENT.

WARNING: Possible explosion hazard. Contact with battery acid may cause severe burns

and blindness. Keep out of reach of children.

ADVERTENCIA: Posible riesgo de una explosión. El contacto con una batería de ácido

puede causar quemaduras y ceguera. Manténgase alejado de los niños.

AVERTISSEMENT : Hasard d’explosion possible. Contact avec l’acide de batterie peut

provoquer sévère brûle et la cécité. Ne le laissez pas a la portée des enfants.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ......................................................................5

PERSONAL PRECAUTIONS .......................................................................................5

CONNECTING THE JUMP STARTER .........................................................................6

FEATURES ................................................................................................................... 7

CHARGING THE INTERNAL BATTERY OF THE JUMP STARTER ............................8

OPERATING INSTRUCTIONS ......................................................................................... 9

MAINTENANCE INSTRUCTIONS ..............................................................................10

MOVING AND STORAGE INSTRUCTIONS ..............................................................10

TROUBLESHOOTING ................................................................................................ 11

BEFORE RETURNING FOR REPAIRS ......................................................................12

SPECIFICATIONS ......................................................................................................13

REPLACEMENT PARTS/ACCESSORIES .................................................................13

LIMITED WARRANTY ................................................................................................14

WARRANTY CARD ....................................................................................................35

CONTENIDOS

INSTRUCCIONES IMPORTANTES DE SEGURIDAD ...............................................15

PRECAUCIONES PERSONALES ..............................................................................15

CONECTAR EL ARRANCADOR ................................................................................16

CARACTERÍSTICAS ..................................................................................................17

PARA CARGAR LA BATERIA INTERNA DEL ARRANCADOR ..................................18

INSTRUCCIONES DE OPERACIÓN ..........................................................................19

INSTRUCCIONES DE MANTENIMIENTO .................................................................21

INSTRUCCIONES PARA EL MANEJO Y ALMACENAMIENTO .................................21

LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS .....................................................21

ANTES DE DEVOLVER A REPARACIONES .............................................................23

ESPECIFICACIONES .................................................................................................23

REPUESTOS / ACCESORIOS ................................................................................... 24

GARANTÍA LIMITADA .................................................................................................24

TARJETA DE GARANTÍA ...........................................................................................35

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ IMPORTANTES ..........................................................25

PRÉCAUTIONS PERSONNELLES ............................................................................ 25

CONNECTE LE AIDE AU DÉMARRAGE ...................................................................26

CARACTÉRISTIQUES ...............................................................................................27

CHARGEMENT DE LA BATTERIE INTERNE DE L’AIDE AU DÉMARRAGE ............28

CONSIGNES D’UTILISATION .................................................................................... 29

INSTRUCTIONS D’ENTRETIEN ................................................................................31

INSTRUCTIONS DE STOCKAGE ET EMPLACEMENT ............................................31

DÉPANNAGE ..............................................................................................................31

AVANT DE RETOURNER POUR LES RÉPARATIONS .............................................33

SPÉCIFICATIONS ......................................................................................................33

PIÈCES DE RECHANGE / ACCESSOIRES...............................................................34

GARANTIE LIMITÉE ...................................................................................................34

CARTE DE GARANTIE ..............................................................................................36

• 5 •

1. IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

WARNING – RISK OF EXPLOSIVE GASES

WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS.

BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION.

IT IS IMPORTANT THAT YOU FOLLOW THESE INSTRUCTIONS EACH TIME

YOU USE THE UNIT.

To reduce the risk of battery explosion, follow these instructions and those published by

the battery manufacturer and the manufacturer of any equipment you intend to use in the

vicinity of a battery. Review cautionary markings on these products and on the engine.

WARNING!

RISK OF ELECTRIC SHOCK OR FIRE.

1.1 Read the entire manual before using this

product. Failure to do so could result in

serious injury or death.

1.2 Keep out of reach of children.

1.3 Do not put ngers or hands into any of the

jump starter’s outlets.

1.4 Do not expose the jump starter to rain

or snow.

1.5 Use only recommended attachments. Use

of an attachment not recommended or

sold by the jump starter manufacturer may

result in a risk of re, electric shock or

injury to persons or damage to property.

1.6 To reduce the risk of damage to the

electric plug or cord, pull by the plug

rather than the cord when disconnecting

the jump starter.

1.7 To reduce the risk of electric shock, unplug

the jump starter charger from the outlet

before attempting any maintenance or

cleaning. Simply turning off the controls will

not reduce this risk.

1.8 Do not operate the jump starter with

damaged cables or clips; replace the

damaged cable or clip immediately.

1.9 Do not operate the jump starter if it has

received a sharp blow, been dropped or

otherwise damaged in any way; take it to

a qualied service person.

1.10 Do not disassemble the jump starter;

take it to a qualied service person when

service or repair is required. Incorrect

reassembly may result in a risk of re or

electric shock.

WARNING! RISK OF EXPLOSIVE GASES.

1.11 To reduce the risk of a battery explosion,

follow these instructions and those

published by the battery manufacturer and

the manufacturer of any equipment you

intend to use in the vicinity of the battery.

Review the cautionary markings on these

products and on the engine.

1.12 This jump starter employs parts, such as

switches and circuit breakers, that tend

to produce arcs and sparks. If used in a

garage, locate this jump starter 18 inches

(46 cm) or more above oor level.

2. PERSONAL PRECAUTIONS

WARNING! RISK OF EXPLOSIVE

GASES. A SPARK NEAR THE BATTERY

MAY CAUSE A BATTERY EXPLOSION.

TO REDUCE THE RISK OF A SPARK

NEAR THE BATTERY:

2.1 NEVER smoke or allow a spark or ame

in the vicinity of a battery or engine.

2.2 Do not permit the internal battery of the

jump starter to freeze. Never charge a

frozen battery.

2.3 To prevent sparking, NEVER allow clips to

touch together or contact the same piece

of metal.

2.4 When charging the internal battery, work

in a well ventilated area and do not restrict

the ventilation in any way.

2.5 Be sure the area around the battery is

well ventilated while the jump starter is

being used.

2.6 Remove personal metal items such as

rings, bracelets, necklaces and watches

when working with a lead-acid battery. A

lead-acid battery can produce a short-

circuit current high enough to weld a ring

or the like to metal, causing a severe burn.

2.7 Be extra cautious, to reduce the risk of

dropping a metal tool onto the battery. It

might spark or short-circuit the battery or

other electrical part that may cause an

explosion.

2.8 Consider having someone nearby to

come to your aid when you work near a

lead-acid battery.

2.9 Have plenty of fresh water and soap

nearby in case battery acid contacts your

skin, clothing or eyes.

2.10 Wear complete eye and body protection,

including safety goggles, face shield and

• 6 •

protective clothing. Avoid touching your

eyes while working near the battery.

2.11 If battery acid contacts your skin or

clothing, immediately wash the area

with soap and water. If acid enters your

eye, immediately ood the eye with cold

running water for at least 10 minutes and

get medical attention right away.

2.12 If battery acid is accidentally swallowed,

drink milk, the whites of eggs or water.

DO NOT induce vomiting. Seek medical

attention immediately.

WARNING! RISK OF CONTACT WITH

BATTERY ACID. BATTERY ACID IS A

HIGHLY CORROSIVE SULFURIC ACID.

2.13 Clean the battery terminals before using

the jump starter. During cleaning, keep

airborne corrosion from coming into

contact with your eyes, nose and mouth.

Use baking soda and water to neutralize

the battery acid and help eliminate

airborne corrosion. Do not touch your

eyes, nose or mouth.

2.14 Add distilled water to each cell until the

battery acid reaches the level specied

by the battery manufacturer. Do not

overll. For a battery without removable

cell caps, such as valve regulated lead

acid batteries (VRLA), carefully follow the

manufacturer’s instructions.

2.15 Read, understand and follow all

instructions for the jump starter, battery,

vehicle and any equipment used near the

battery and jump starter.

2.16 Determine the voltage of the battery by

referring to the vehicle owner’s manual

and make sure that the output voltage of

the jump starter is correct.

2.17 Make sure that the jump starter cable

clips make tight connections.

2.18 WARNING: This product contains one

or more chemicals known to the State

of California to cause cancer and birth

defects or other reproductive harm.

3. CONNECTING THE JUMP STARTER

WARNING! A SPARK NEAR THE

BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK

OF A SPARK NEAR THE BATTERY:

3.1 Attach the output cables to the battery

and chassis as indicated below. Never

allow the output clips to touch each other.

3.2 Position the DC cables to reduce the risk of

damage by the hood, door and moving or

hot engine parts. NOTE: If it is necessary

to close the hood during the jump starting

process, ensure that the hood does not

touch the metal part of the battery clips or

cut the insulation of the cables.

3.3 Stay clear of fan blades, belts, pulleys

and other parts that can cause injury.

3.4 Check the polarity of the battery posts.

The POSITIVE (POS, P, +) battery post

usually has a larger diameter than the

NEGATIVE (NEG, N, -) post.

3.5 Determine which post of the battery is

grounded (connected) to the chassis.

If the negative post is grounded to the

chassis (as in most vehicles), see step

3.6. If the positive post is grounded to the

chassis, see step 3.7.

3.6 For a negative-grounded vehicle, connect

the POSITIVE (RED) clip from the jump

starter to the POSITIVE (POS, P, +)

ungrounded post of the battery. Connect

the NEGATIVE (BLACK) clip to the

vehicle chassis or engine block away from

the battery. Do not connect the clip to the

carburetor, fuel lines or sheet-metal body

parts. Connect to a heavy gauge metal

part of the frame or engine block.

3.7 For a positive-grounded vehicle, connect

the NEGATIVE (BLACK) clip from the

jump starter to the NEGATIVE (NEG, N, -)

ungrounded post of the battery. Connect

the POSITIVE (RED) clip to the vehicle

chassis or engine block away from the

battery. Do not connect the clip to the

carburetor, fuel lines or sheet-metal body

parts. Connect to a heavy gauge metal

part of the frame or engine block.

3.8 When disconnecting the jump starter, turn

all switches to off (if applicable), remove

the clip from the vehicle chassis, then

remove the clip from the battery terminal.

• 7 •

4. FEATURES

Jump Starter

1. Heavy-duty battery clamps

2. 12V DC socket

3. Jump starter ON/OFF switch

4. Digital display

5. Display button

6. USB port

7. USB button

2 3 4 5

Charger

1. Charging status LED

2. Bad Battery LED

3. Power LED

4.1 Digital Display

When connected to a battery, the digital

display can be used to indicate the battery’s

voltage. When not connected to a battery,

the digital display can be used to indicate

the percent of charge or the voltage of the

jump starter’s internal battery.

To check the internal battery’s charge

status, make sure the rotary switch is in

the OFF position, then press the display

button on the front of the jump starter.

The digital display will show the battery’s

percent of charge. A fully charged battery

will read 100%. Charge the internal battery

if the display shows it is under 100%.

NOTE: The internal battery’s percent of

charge is most accurate when the jump

starter has been disconnected from all

devices and charging sources for a few

hours.

To check the voltage level of the jump

starter’s internal battery, make sure the

clips are attached to their plastic storage

holders and not touching each other,

and then turn the rotary switch to the

12V position (12V or 24V position on

DSR115). The display will indicate the

battery’s voltage.

To check the voltage level of the vehicle’s

battery, make sure the switch in the OFF

position, then connect the clips to the

vehicle’s battery. The display will indicate

the battery’s voltage.

4.2 Charger LED Indicators

POWER (green) LED lit: The

charger is connected to AC power.

CHARGING STATUS LED (green)

pulsing slowly: The charger is

charging the jump starter’s internal

battery, or the battery is fully

charged and the charger is in

Maintain mode.

CHARGING STATUS LED

(yellow/orange) ashing rapidly:

The charger has detected a problem

with the battery. See Troubleshooting

for more information.

BAD BATTERY (red) LED lit:

The charger has detected a problem

with the battery. SeeTroubleshooting

for more information.

• 8 •

5. CHARGING THE INTERNAL BATTERY OF THE JUMP STARTER

IMPORTANT!

CHARGE IMMEDIATELY AFTER

PURCHASE, AFTER EACH USE AND

EVERY 30 DAYS, TO KEEP THE UNIT’S

INTERNAL BATTERY FULLY CHARGED

AND PROLONG BATTERY LIFE.

To check the internal battery’s charge

status, make sure the rotary switch is in the

OFF position, then press the display button

on the front of the jump starter. The digital

display will show the battery’s percent of

charge. A fully charged battery will read

100%. Charge the internal battery if the

display shows it is under 100%. Complete

charging may take up to 24 hours.

5.1 Grounding and AC Power Cord

Connections

IMPORTANT: Only use the charger that

was included with the jump starter to charge

the internal battery of the jump starter.

Using a different charger could result in

personal injury or property damage.

WARNING!

RISK OF ELECTRIC SHOCK OR FIRE.

This battery charger is for use on a

nominal 120V circuit. The plug must be

plugged into an outlet that is properly

installed in accordance with all local

codes and ordinances. The plug pins

must t the receptacle (outlet). Do not use

with an ungrounded system.

DANGER. Never alter the AC cord or plug

provided – if it does not t the outlet, have

a proper outlet installed by a qualied

electrician. An improper connection can

result in a risk of an electric shock or

electrocution.

An extension cord should not be used

unless absolutely necessary. Use of an

improper extension cord could result

in a risk of re and electric shock. If an

extension cord must be used, make sure:

• That the pins on the plug of the extension

cord are the same number, size and

shape as those of the plug on the charger.

• That the extension cord is properly wired

and in good electrical condition.

• That the wire size is large enough for the

AC ampere rating of the charger,

as specied:

Length of cord (feet) 25 50 100 150

AWG* size of cord 18 18 18 16

*AWG-American Wire Gauge

5.2 Charging the Jump Starter

with included Charger

1. Make sure the charger and jump starter

are placed on a dry, nonammable

surface. To charge the jump starter, plug

the charger into the charging port on the

front of the jump starter.

2. Conrm the AC outlet voltage matches

the input voltage of the charger.

3. Connect the charger to the AC wall

outlet and conrm that the green

POWER LED on the charger turns on.

4. Check that the green

CHARGING

STATUS LED on the charger is pulsing

slowly, to indicate that charge process

has started. To see the status of the

charge, check the percentage shown

on the jump starter display.

5. When the jump starter display shows

100 (%), the internal battery is fully

charged and the jump starter is ready

to use. Complete charging may take up

to 24 hours.

NOTE: The green

CHARGING

STATUS LED will remain pulsing after

the display shows 100%, as the charger

automatically goes into Maintain mode

and maintains the battery at full charge

without damaging it.

6. After the charge is complete, disconnect

the charger from the AC outlet, then

disconnect the charger from jump starter.

5.3 Charger Modes

Automatic charging mode

When an automatic charge is performed,

the charger switches to maintain mode

automatically after the battery is charged.

Aborted Charge

If charging cannot be completed normally,

charging will abort. When charging aborts,

the charger’s output is shut off. The BAD

BATTERY (red) LED will light. Do

not continue attempting to charge the

battery. Check the battery and replace, if

necessary.

Desulfation Mode

Desulfation could take 8 to 10 hours. If

desulfation fails, charging will abort. The

red BAD BATTERY

LED will light and

the yellow/orange CHARGING STATUS

LED will ash.

Completion of Charge

When the internal battery is fully charged,

the jump starter’s display will show “100”.

• 9 •

Maintain Mode (Float Mode Monitoring)

When the internal battery is fully charged

and the jump starter display shows “100”,

the charger has started maintain mode. In

this mode, the charger keeps the battery

fully charged by delivering a small current

when necessary. If the charger has to

provide its maximum maintain current for

a continuous 12 hour period, it will go into

abort mode (see Aborted Charge). This

is usually an indication of a bad battery;

have the jump starter checked.

5.4 Charging the Internal Battery

While Driving

You may also charge the internal battery

while driving, using a male-to-male charger

cable (part number 94500109 – sold

separately).

IMPORTANT: DO NOT CHARGE THE

INTERNAL BATTERY FOR MORE THAN

30 MINUTES OR LEAVE THE BATTERY

UNATTENDED. IT COULD EXPLODE,

CAUSING PROPERTY DAMAGE OR

PERSONAL INJURY.

1. Make sure the car is running.

2. Insert one end of the accessory cable

into the 12V DC power outlet.

3. Insert the other end of the accessory

cable into the vehicle’s accessory

outlet (lighter socket).

NOTE: Using this method to charge the

battery overrides the maintain mode and

the battery can be overcharged.

4. Monitor the progress of the charge by

pressing the Percentage of Charge

button on the front of the unit. Do not

leave the battery unattended or it could

explode, causing property damage and

personal injury. When the battery is fully

charged, disconnect the accessory cable

from the jump starter, and then from the

lighter socket of the vehicle.

NOTE: Completely disconnect the charger

cable when the engine is not running.

6. OPERATING INSTRUCTIONS

6.1 Jump Starting a Vehicle Engine

IMPORTANT: Using the jump starter

without a battery installed in the vehicle will

damage the vehicle’s electrical system.

IMPORTANT: Do not use the jump starter

while charging its internal battery.

1. Turn the vehicle’s ignition OFF before

making cable connections.

2. Make sure the rotary switch on the

front of the jump starter is in the OFF

position. Connect the jump starter to

the battery, following the precautions

listed in section 3.

WARNING! RISK OF EXPLOSION.

If you have connected the clips backward,

an audio alarm will sound. DO NOT turn

the rotary switch to the 12V (12V or 24V

for model DSR115) position. This could

cause serious damage to the jump starter

or the vehicle. Reverse the connections

and the audio alarm will stop.

3. If no audio alarm sounds, turn the

rotary switch to the 12V position (12V

or 24V position for model DSR115).

The clips are now powered.

4. Crank the engine. If the engine does not

start within 3-8 seconds, stop cranking

and wait at least 1 minute before

attempting to start the vehicle again.

(This permits the battery to cool down.)

5. After the engine starts, turn the rotary

switch to the OFF position. Disconnect

the black clip (-), then the red clip (+) in

that order, and clip them back onto the

jump starter storage holders.

6. Recharge the jump starter as soon as

possible after use.

NOTE: If the cables are connected to a

24 volt system when the switch is in the

12 volt position, the audio alarm will

sound continuously. TURN OFF the jump

starter immediately or internal battery

damage could occur.

NOTE: If the switch is in the 12V or 24V

position or the jump starter is connected to

a battery for more than ve minutes, four

beeps will sound. This is a reminder to turn

the jump starter off and/or disconnect it

from the vehicle’s battery when not in use.

WARNING! RISK OF EXPLOSION.

To prevent sparking, NEVER allow the

clips to touch together or to contact the

same piece of metal. Never attempt to

jump start a frozen battery.

6.2 Powering A 12V DC Device:

The jump starter is a power source for all

12V DC accessories that are equipped

with a 12V accessory plug. Use it for

power outages and shing or camping

trips. Estimated usage time is listed in the

following chart.

1. Make sure the device to be powered

is OFF before inserting a 12V DC

accessory plug into the 12V DC socket.

2. Ensure the battery clips are securely

clipped on the storage holders.

3. Open the protective cover of the 12V DC

power outlet on the front of the jump

starter.

4. Plug the 12V DC device into the 12V

DC power outlet, and turn on the 12V

DC device (if required).

5. If the 12V DC device draws more than

15A or has a short circuit, the internal

• 10 •

circuit breaker of the jump starter

will trip and disconnect the power to

the device. Disconnect the 12V DC

device. The breaker will automatically

reset a short time after an overload is

disconnected.

6. Recharge immediately after unplugging

the 12V DC device.

NOTE: The DC power outlet is wired

directly to the internal battery. Extended

operation of a 12V DC device may result

in excessive battery drain.

12V DC ESTIMATED RUN-TIMES

APPLIANCE

TYPE

EST.

WATTAGE

EST.

RUN TIME

DSR114

EST.

RUN TIME

DSR114

Cell phone,

uorescent light

4 watts 66 hrs. 132 hrs.

Radio, fan,

depth nder

9 watts 29.3 hrs. 58.6 hrs.

Camcorder 15 watts 17.6 hrs. 35.2 hrs.

Electric tool 24 watts 11 hrs. 22 hrs.

Electric cooler 48 watts 5.5 hrs. 11 hrs.

Car vacuum,

air compressor

80 watts 3.3 hrs. 6.6 hrs.

NOTE: Estimated run-times. Actual time may vary.

Times are based on the internal battery being fully charged.

6.3 USING THE USB PORT

The USB port provides up to 2.1A at 5V DC.

1. Ensure the battery clips are securely

clipped on the storage holders.

2. Press the USB button on the front of

the unit.

3. Plug the device into the USB port on

the front of the unit.

4. Turn the USB device on.

5. Reverse these steps when nished

using the USB port.

6. Charge the jump starter as soon as

possible after using the USB port.

7. MAINTENANCE INSTRUCTIONS

7.1 After use and before performing

maintenance, unplug and disconnect

the jump starter.

7.2 Use a dry cloth to wipe all battery corrosion

and other dirt or oil from the battery clips,

cords and the jump starter case.

7.3 Ensure that all of the jump starter

components are in place and in good

working condition.

7.4 All servicing should be performed by

qualied service personnel.

8. MOVING AND STORAGE INSTRUCTIONS

8.1 Store inside, in a cool, dry place.

8.2 Do not store the clips on the handle,

clipped together, on or around metal, or

clipped to cables. The clips on the jump

starter are live when the switch is in the

ON position and will produce arcing or

sparking if they come in contact with each

other. To prevent accidental arcing, always

place the switch in the OFF position and

keep the clips on the storage holders when

not using it to jump start a vehicle.

8.3 If the jump starter is moved around the

shop or transported to another location,

take care to avoid/prevent damage to the

cords, clips and jump starter. Failure to

do so could result in personal injury or

property damage.

IMPORTANT: Do not use and/or store the

jump starter in or on any area or surface

where damage could occur if the internal

battery should unexpectedly leak acid.

8.4 IMPORTANT:

• CHARGE IMMEDIATELY AFTER

PURCHASE

• KEEP FULLY CHARGED

Charge the jump starter’s internal battery

immediately after purchase, after every

use and every 30 days.

All batteries are affected by temperature.

The ideal storage temperature is at

70°F. The internal battery will gradually

self-discharge (lose power) over time,

especially in warm environments. Leaving

the battery in a discharged state may

result in permanent battery damage. To

ensure satisfactory performance and

avoid permanent damage, charge the

internal battery every month.

• 11 •

9. TROUBLESHOOTING

Jump Starter

PROBLEM POSSIBLE CAUSE SOLUTION

The jump starter won’t

jump start my car.

Clamps are not making a good

connection to the battery.

The jump starter’s battery is not

charged.

The vehicle’s battery is defective.

Check for poor connection to

battery and frame. Make sure

connection points are clean.

Check the battery charge status

by pressing the Display button

on the front of the unit. The

display will show the percentage

of charge.

Have the battery checked.

The jump starter won’t

power my 12V device.

The 12V device is not

turned on.

The jump starter’s battery is not

charged.

The 12V device draws more

than 15A or has a short circuit.

Turn on the 12V device.

Check the battery charge status

by pressing the Display button

on the front of the unit. The

display will show the percentage

of charge.

Disconnect the 12V device. The

internal breaker will automatically

reset after a minute or two. Try

using the 12V device again.

The battery in the jump

starter won’t hold a

charge.

The battery is bad (will not

accept a charge).

Replace the battery.

The jump starter’s alarm

is on.

Connections are reversed. Disconnect the jump starter and

reverse the clamps.

• 12 •

Charger

PROBLEM REASON SOLUTION

The green

POWER

LED does not light when

charger is properly

connected.

AC outlet is dead.

Poor electrical connection.

Check for open fuse or circuit

breaker supplying AC outlet.

Check power cord and extension

cord for a loose tting plug.

The red BAD

BATTERY LED is lit.

The battery is sulfated.

Lack of progress is detected and

battery voltage is below 14.2V.

The battery’s initial voltage is

below 12.2V and the total input

is less than 1.5 Ah.

The battery voltage drops

below 12.2V during Maintain

Mode.

The charger is in desulfation

mode. Continue charging for

several hours. If not successful,

have the battery checked.

The battery may be overheated. If

so, allow the battery to cool. The

battery may be too large or have a

short circuit. Have battery checked

or replaced.

The battery capacity is too low,

or the battery is too old. Have it

checked or replaced.

The battery won’t hold a charge.

May be caused by a drain on

the battery or the battery could

be bad. Make sure there are no

loads on the battery. If there are

remove them. If there are none,

have the battery checked or

replaced.

The red BAD

BATTERY LED is lit and

the yellow/orange

CHARGING STATUS

LED is ashing rapidly.

The battery voltage is still below

10V after 2 hours of charging.

(or)

In maintain mode, the output

current is more than 1.5A for 12

hours.

Desulfation was unsuccessful.

The battery may be defective.

Make sure there are no loads on

the battery. If there are, remove

them. If there are none, have the

battery checked or replaced.

The battery may be defective.

Have battery checked or replaced.

10. BEFORE RETURNING FOR REPAIRS

If these solutions do not eliminate the problem,

or for more information about troubleshooting,

contact customer service for assistance:

[email protected]

www.batterychargers.com

or call 1-800-621-5485

Monday-Friday 7:00am to 5:00pm CST

For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485.

DO NOT SHIP UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION

(RMA) number from Customer Service at Schumacher Electric Corporation.

• 13 •

11. SPECIFICATIONS

DSR114

Internal Battery Type .....................................Sealed, Maintenance Free, AGM, Lead-Acid

Nominal Voltage ......................................................................................................12V DC

Capacity ......................................................................................................................22Ah

DC Power Output (Maximum Continuous Load)............................................. 12V DC/15A

Peak Amps .................................................................................................................. 2200

Cranking Amps.............................................................................................................. 525

Cold Cranking Amps ..................................................................................................... 350

Battery Hookup Cables ......................................................................4 AWG, 60˝ (152 cm)

Dimensions (H x W x D)........................................ 16.7˝ x 12.9˝ x 5.5˝ (42.5 x 33 x 14 cm)

Weight ..................................................................................................... 18.73 lbs (8.5 kg)

DSR115

Internal Battery Type .....................................Sealed, Maintenance Free, AGM, Lead-Acid

Nominal Voltage .............................................................................................. 12V/24V DC

Capacity ................................................................................................................ (2) 22Ah

DC Power Output (Maximum Continuous Load)............................................. 12V DC/15A

Peak Amps .................................................................................................................. 4400

Cranking Amps..................................................................................750 (12V) / 475 (24V)

Cold Cranking Amps .........................................................................525 (12V) / 350 (24V)

Battery Hookup Cables ......................................................................2 AWG, 60˝ (152 cm)

Dimensions (H x W x D)........................................ 16.7˝ x 12.9˝ x 7.4˝ (42.5 x 33 x 19 cm)

Weight ...................................................................................................... 39.68 lbs (18 kg)

Charger

Input voltage ..................................................................................120V AC @ 60Hz, 0.5A

Output voltage.........................................................................................................12V DC

Output current rating ....................................................................................................... 2A

12. REPLACEMENT PARTS/ACCESSORIES

Male-to-male accessory cable ............................................................................ 94500109

DSR2 Charger ........................................................................................... 2299003063CZ

Replacement battery (DSR115 uses 2) ........................................................5799000010Z

• 14 •

13. LIMITED WARRANTY

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT

PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE ORIGINAL

RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY IS NOT

TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this jump starter for one

(1) year from the date of purchase at retail against defective material or workmanship that

may occur under normal use and care. If your unit is not free from defective material or

workmanship, Manufacturer’s obligation under this warranty is solely to repair or replace

your product, with a new or reconditioned unit, at the option of the Manufacturer. It is the

obligation of the purchaser to forward the unit, along with proof of purchase and mailing

charges prepaid to the Manufacturer or its authorized representatives in order for repair

or replacement to occur.

Manufacturer does not provide any warranty for any accessories used with this product

that are not manufactured by Schumacher Electric Corporation and approved for use with

this product. This Limited Warranty is void if the product is misused, subjected to careless

handling, repaired, or modied by anyone other than Manufacturer or if this unit is resold

through an unauthorized retailer.

Manufacturer makes no other warranties, including, but not limited to, express, implied or

statutory warranties, including without limitation, any implied warranty of merchantability or

implied warranty of tness for a particular purpose. Further, Manufacturer shall not be liable

for any incidental, special or consequential damage claims incurred by purchasers, users

or others associated with this product, including, but not limited to, lost prots, revenues,

anticipated sales, business opportunities, goodwill, business interruption and any other injury

or damage. Any and all such warranties, other than the limited warranty included herein,

are hereby expressly disclaimed and excluded. Some states do not allow the exclusion or

limitation of incidental or consequential damages or length of implied warranty, so the above

limitations or exclusions may not apply to you. This warranty gives you specic legal rights

and it is possible you may have other rights which vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE

MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME OR

MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN THIS

WARRANTY.

Schumacher

and the Schumacher logo are registered trademarks

of Schumacher Electric Corporation.

Page is loading ...

• 35 •

1 YEAR LIMITED

WARRANTY PROGRAM

REGISTRATION

MODEL: _____________________DESCRIPTION: ________________________

This is the only express limited warranty, and the manufacturer neither assumes

nor authorizes anyone to assume or make any other obligation. There is no other

warranty, other than what is described in the product owner’s manual.

The warranty card should be submitted within 30 days of purchase. The customer

must keep the ORIGINAL receipt because it will be required for any warranty claims.

This warranty is not transferable. Send warranty card only.

DO NOT SEND UNIT TO THIS ADDRESS FOR REPAIR.

Mail this card to: Schumacher Electric Corporation

801 Business Center Drive

Mount Prospect, IL 60056-2179

Name ______________________________________________________________

Street Address _______________________________________________________

City ________________________________State _________ Zip Code _________

Phone _____________________Email ___________________________________

Store Name Where Purchased ___________________ Date of Purchase _________

Store Location ____________________ UPC Number ________________________

Serial Number ______________________________________ (SEE PRODUCT)

For faster warranty activation, go to www.batterychargers.com to register your product online.

PROGRAMA DE REGISTRO

DE 1-AÑO DE GARANTÍA

LIMITADA

MODELO: ____________________DESCRIPCIÓN: ________________________

Esta es la única garantía limitada expresa, y el productor no autoriza ni otorga

a alguien a realizar alguna otra obligación. No existe ninguna otra garantía

más que la descrita en el manual del dueño.

La tarjeta de garantía debe enviarse durante los primeros 30 días después de la

compra. El cliente debe mantener el recibo de compra ORIGINAL como

comprobante, el cual le otorga todo derecho a cualquier reclamo de garantía.

Esta garantía no es transferible. Envie tarjeta de garantía solamente.

NO ENVÍE LA UNIDAD A ESTA DIRECCIÓN PARA SU REPARACIÓN.

Enviar esta tarjeta a: Schumacher Electric Corporation

801 Business Center Drive

Mount Prospect, IL 60056-2179

Nombre ____________________________________________________________

Dirección ___________________________________________________________

Ciudad __________________________Estado ____________ C.P. _____________

Tel: ________________________ Correo electrónico _________________________

Nombre de la Tienda donde se Compró ____________ Fecha de compra _________

Localización de la Tienda ____________ Numero de Serie ____________________

Código de barras ___________________________ (CONSULTE EL PRODUCTO)

Para una activación más rápida, visite nuestra página de internet en www.batterychargers.com

¡AHORRE EN EL ENVÍO! ¡ACTIVE SU GARANTÍA EN LÍNEA-LA FORMA MAS RÁPIDA Y FÁCIL!

Visite nuestra página en www.batterychargers.com para registrar su producto en línea.

WARRANTY CARD / TARJETA DE GARANTÍA

SAVE ON POSTAGE! ACTIVATE YOUR WARRANTY ONLINE – THE QUICK AND EASY WAY!

Go to www.batterychargers.com to register your product online.

WARRANTY CARD

TARJETA DE GARANTÍA

Page is loading ...

Schumacher DSR115 Owner's manual

Brand: Schumacher

Model: DSR115

Category: Battery chargers

Type: Owner's manual

Download PDF

report

in other languages

français: Schumacher DSR115 Le manuel du propriétaire
español: Schumacher DSR115 El manual del propietario

Schumacher DSR115 Owner's manual

Schumacher DSR115 Owner's manual

in other languages

Related papers

Other documents