Operation
1
3
2
54
• Open the housing lid (see picture 1 + 2).
• Insert the smartphone into the clip (see picture 2). The upper clamp is spring-mounted. Use the smartphone
to push the upper clamp upwards until the smartphone rests on the lower clamp. Align the center of the
display exactly to the center of the clip.
• Use the upper rotary control to adjust the lenses according to the distance between your eyes (see
picture 3).
• Use the rotary knobs on the sides to adjust the focus (see picture 4).
• Turn the lens rings for ne adjustment of the focus (see picture 5).
Tips and notes
• Adjust the length of the head strap to the size of your head. There are hook-and-loop fasteners located
underneath the rectangular patches.
• Guide any required cables (e.g. headphones, charging cable) from outside through the recesses on the
side.
• Remove the front panel to expose the smartphone camera for augmented reality applications.
• If the pre-installed foam paddings come loose, install the replacement foam paddings.
Cleaning and care
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical solutions
since these can penetrate the housing or impair functionality.
• Remove the smartphone before cleaning the product.
• Use the included cleaning cloth for cleaning the lenses.
• Clean the product with a dry, bre-free cloth.
Disposal
At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines.
You thus full your statutory obligations and contribute to the protection of the environment.
Technical data
Material ........................................................................... ABS (housing), resin (lenses),
nylon + PU (head strap), PU (padding)
Lens distance ................................................................. 57 – 72 mm
Viewing angle ................................................................. 90º
Operating conditions ....................................................... -35 to +40 °C, 10 – 85 % RH
Storage conditions .......................................................... -10 to +50 °C, 5 – 90 % RH
Dimensions of suitable smartphones (W x H x D) .......... max. 81 x 154 x 10 mm
Dimensions (W x H x D) ................................................. 200 x 95 x 135 mm
Weight ............................................................................ 378 g
Operating instructions
Virtual Reality 3D glasses
Item no. 1462833
Intended use
The product is intended for viewing 3D applications (videos, games, or apps) on a smartphone.
For safety reasons, you must not convert and/or modify this product. If you use the product for purposes
other than those described above, the product may be damaged. Read the instructions carefully and keep
them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Virtual Reality glasses
• Cleaning cloth
• 2 x foam sticker sets (1 set being pre-installed)
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions from our website www.conrad.com/downloads or scan the printed
QR code. Follow the instructions on the website.
Description of symbols
The symbol with an exclamation mark in a triangle indicates important instructions contained in
these operating instructions that must be followed.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Do not use the product for viewing bright light sources, especially such as the sun. Viewing
unltered sunlight even for just a split of a second can cause permanent blindness.
• Risk of re! If used improperly, the product can act like a burning lens and concentrate sunrays
on one small spot, causing very high temperatures.
• Prolonged use can cause fatigue. Use the product appropriately.
• The product can cause epileptic seizures in some people.
• If your eyes are irritated, stop using the product. If that does not provide any relief, make sure
to consult a doctor.
• Use the product in a safe environment. Using the product can cause loss of balance. Make
sure your surroundings are safe or secured before wearing the product.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modications and repairs are to be performed exclusively by an expert or at a
qualied shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE. *1462833_V1_0716_02_IPL_m_en
1
2
3
4
Renkforce 2692574 User manual
Renkforce Controller PC, iOS, Android Owner's manual
Reely 1529670 Operating instructions
Speaka SP-TVM-601 User manual
VOLTCRAFT QCP-3000 Operating Instructions Manual
Conrad Alatech Cyclaid 10 BLE Operating Instructions Manual
VOLTCRAFT 10050 Operating Instructions Manual
