INSTALLATION, OPERATION, & MAINTENANCE OF APOLLO
BARSTOCK VALVES
I965100.B 10/2013
PRE-INSTALLATION
Prior to installation, it is imperative that compatibility between valve construction materials and the media
being used is verified. Valve and/or nameplate markings should be reviewed to ensure that the valve is
properly rated for the intended service.
The valve should be examined visually and manually operated prior to installation. Particular attention
should be paid to pipe threads to make sure there are no foreign materials or defects.
INSTALLATION
It is extremely important to make certain that the valve and piping being installed are properly supported,
and that the valve and piping are properly aligned.
Globe valves have an arrow stamped on the side of the body indicating flow direction. Care must be taken
to ensure that the inlet end is against the line pressure.
Once installation is complete, it is recommended that the entire system be pressurized and inspected for
leakage. If leakage is detected, the valve and/or piping should be repaired or replaced prior to being placed
into service.
ROUTINE INSPECTION AND MAINTENANCE
Periodic inspection of critical leak path areas such as the body/bonnet joint, end connections, and around
the stem packing is required.
The most common area for leakage is around the stem packing due to normal wear. Stem leakage can
generally be stopped by adjusting the packing. This is accomplished by turning the packing nut in quarter-
turn increments until leakage stops. If leakage cannot be stopped by adjusting the packing nut, replacement
of the stem packing is required (refer to the Repair section).
REPLACEMENT PARTS
It is recommended to use only genuine Apollo replacement parts. These parts are usually available from
stock and are manufactured to the same specifications as those originally supplied with Apollo valves.
Information obtained from markings on the the valve body and nameplate is useful when ordering
replacement parts from your local Apollo distributor.
FIELD REPAIR
STEM LEAKAGE
The most common area of leakage is around the stem and packing. Adjusting the packing nut can normally
stop most leakage issues. If tightening the packing not does not stop the stem leakage, the stem packing
must be replaced.
All Apollo globe valves are equipped with backseats which are 100% tested prior to shipment. However,
once the valve is put into service, corrosion and foreign material can affect the sealing integrity of the
backseat. Therefore, REPACKING UNDER PRESSURE CAN BE HAZARDOUS. For this reason,
Conbraco strongly recommends that the system and valve be depressurized before attempting any repair
work. After isolating the valve from pressure, the following procedure should be used to repack the valve.
INSTALLATION, OPERATION, & MAINTENANCE OF APOLLO
BARSTOCK VALVES
I965100.B 10/2013
1. Remove the handwheel or handle nut (1), handwheel or handle (2), packing nut (3), and packing
gland (4) and packing washer (5), if applicable.
2. Remove the old stem packing (6). Care should be taken not to scratch or damage the stem or
stuffing box.
3. Clean and inspect the stem, stuffing box, and gland. Parts should be replaced if any heavy
scratches, nicks, or corrosion are found.
4. Install the new stem packing.
5. Replace the packing washer (5), if applicable, the packing gland (4), packing nut (3), handwheel
or handle (2), and handwheel or handle nut (1).
6. Tighten the packing nut until the packing is lightly compressed. Cycle the valve several times.
7. If slight stem leakage occurs after the system is pressurized, continue tightening the packing nut in
quarter-turn increments until the leakage stops.
Handwheel Nut (1)
Handwheel (2)
Packing Nut (3)
Packing Gland (4)
Optional Packing
Washer (5)
Stem Packing (6)
Stem (7)
Hub (8)
Body (9)
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Apollo Conbraco 6GB110B1LF Installation guide
-
-
-
-
Apollo 73A14515A Installation guide
-
Apollo 9610801 Installation guide
-
-
Apollo Valves 88A24501 Installation guide
-
Apollo Conbraco 82LF24501 Installation guide
-
Other documents
-
Crane Valve/Crane Energy Flow Sol 431UB*004 Installation guide
-
Milwaukee Valve 515 - 100 Installation guide
-
Hancock Forged Steel Gate, Globe and Check Valves IOM Owner's manual
-
Emerson 24000SB User manual
-
Vogt Valves AAB85VV001001 Installation guide
-
Fasani Pressure Seal Globe Valves - Style B Owner's manual
-
Sempell Pressure Seal Globe Valves - Style A Owner's manual
-
NIBCO NHA300F Installation guide
-
Hancock Cast Steel Gate, Globe and Check Valves IOM Owner's manual
-
Yarway Forged Steel Gate Valves, Series 950 IOM Owner's manual
