Black & Decker KX2001 Owner's manual

Category
Power tools
Type
Owner's manual

This manual is also suitable for

3
ENGLISH
(Original instructions)
Intended use
Your Black & Decker heat gun has been designed for various
heating applications such as paint stripping. This product is
intended for consumer use and indoor use only.
Safety instructions
General power tool safety warn-
ings
@
Warning! Read all safety
warnings and all instruc-
tions.
Failure to follow the warn-
ings and instructions listed below
may result in electric shock, re and/
or serious injury.
Save all warnings and instruc-
tions for future reference.
The term
"power tool" in all of the warnings listed below
refers to your mains operated (corded) power
tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well
lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in
explosive atmospheres, such
as in the presence of
ammable liquids, gases or
dust.
Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders
away while operating a power
tool.
Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match
the outlet. Never modify the
plug in any way. Do not use
any adapter plugs with earthed
(grounded) power tools.
Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with
earthed or grounded surfaces
such as pipes, radiators,
ranges and refrigerators.
There is
an increased risk of electric shock if your
body is earthed or grounded.
c. Do not expose power tools to
rain or wet conditions.
Water
entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never
use the cord for carrying,
pulling or unplugging the
power tool. Keep cord away
from heat, oil, sharp edges or
moving parts.
Damaged or entangled
cords increase the risk of electric shock.
e. When operating a power tool
outdoors, use an extension
cord suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f. If operating a power tool in a
damp location is unavoidable,
use a residual current device
(RCD) protected supply.
Use of an
RCD reduces the risk of electric shock.
4
ENGLISH
(Original instructions)
3. Personal safety
a. Stay alert, watch what you are
doing and use common sense
when operating a power tool.
Do not use a power tool while
you are tired or under the
inuence of drugs, alcohol or
medication.
A moment of inattention
while operating power tools may result in
serious personal injury.
b. Use personal protective
equipment. Always wear eye
protection.
Protective equipment such
as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting.
Ensure the switch is in the
off-position before connecting
to power source and/or battery
pack, picking up or carrying
the tool.
Carrying power tools with your
nger on the switch or energising power
tools that have the switch on invites
accidents.
d. Remove any adjusting key or
wrench before turning the
power tool on.
A wrench or a key left
attached to a rotating part of the power tool
may result in personal injury.
e. Do not overreach. Keep proper
footing and balance at all
times.
This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear
loose clothing or jewellery.
Keep your hair, clothing and
gloves away from moving
parts.
Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the
connection of dust extraction
and collection facilities, ensure
these are connected and
properly used.
Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool.
Use the correct power tool for
your application.
The correct power
tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if
the switch does not turn it on
and off.
Any power tool that cannot be
controlled with the switch is dangerous and
must be repaired.
c. Disconnect the plug from the
power source and/or the
battery pack from the power
tool before making any
adjustments, changing
accessories, or storing power
tools.
Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
5
ENGLISH
(Original instructions)
d. Store idle power tools out of
the reach of children and do
not allow persons unfamiliar
with the power tool or these
instructions to operate the
power tool.
Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of
parts and any other condition
that may affect the power tools
operation. If damaged, have
the power tool repaired before
use.
Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and
clean.
Properly maintained cutting tools
with sharp cutting edges are less likely to
bind and are easier to control.
g. Use the power tool,
accessories and tool bits etc.
in accordance with these
instructions, taking into
account the working
conditions and the work to be
performed.
Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5. Service
a. Have your power tool serviced
by a qualied repair person
using only identical
replacement parts.
This will ensure
that the safety of the power tool is
maintained.
Additional power tool safety
warnings
@
Warning!
Additional safety
instructions for heat guns.
Warning:
Do not use outdoors, indoor use
only.
Warning:
This appliance must be placed on
its stand when not in use.
Warning:
A re may result if the appliance
is not used with care, therefore be careful when
using the appliance in places where there are
combustible materials.
u
Do not apply heat to the same place for a
long time.
u
Do not use in presence of an explosive
atmosphere.
u
Be aware that heat may be conducted to
combustible materials that are out of sight.
u
Place the appliance on its stand after use
and allow it to cool down before storage.
u
Do not leave the appliance unattended
when it is switched on.
u
Do not obstruct either the air intake slots or
the nozzle outlet as this may cause exces-
sive heat build up resulting in damage to the
appliance.
u
Do not direct the hot air ow at other people
or animals.
u
Do not touch the nozzle as it becomes very
hot during use and remains hot for up to 30
minutes after use.
u
Do not place the nozzle against any object
during or immediately after use.
u
Do not poke anything down the nozzle as it
could give you an electric shock.
6
ENGLISH
(Original instructions)
u
Do not look down the nozzle while the appli-
ance is switched on.
u
Do not use the appliance as a hair dryer!
The air temperature is far higher than a hair
dryer.
u
Ensure adequate ventilation during use as
toxic fumes may be produced.
u
Do not use the appliance in a damp atmos-
phere.
u
When stripping paint, ensure that the
work area is enclosed. Wear a dust mask
specically designed for protection against
lead paint dust and fumes and ensure that
persons within or entering the work area are
also protected.
u
Do not burn paint, as it could cause a re
hazard.
u
Do not allow paint to adhere to the nozzle as
it could ignite after some time.
u
Switch off the appliance and allow it to cool
before tting any accessory.
Stripping lead-based paint
u
Extreme care should be taken when
stripping paint. The peelings, residue and
vapours of paint may contain lead, which is
poisonous. Any pre-1960 building may in the
past have been painted with paint contain-
ing lead. This paint may be covered with
additional layers of paint. Once deposited on
surfaces, hand to mouth contact can result
in the ingestion of lead.
u
Exposures to even low levels of lead can
cause irreversible brain and nervous system
damage. The greatest danger of lead poi-
soning is to children and pregnant women.
u
Before starting work, it is important to
determine whether the paint to be stripped
contains lead. This can be done using a
test kit or by a professional decorator. Do
not smoke, eat or drink in a work area that
could or may be contaminated by lead. Lead
based paints should only be removed by
a professional and should not be removed
using a heat gun.
Safety of others
u
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and knowl-
edge if they have been given supervision or
instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by children without super-
vision.
u
Children should be supervised to ensure
that they do not play with the appliance.
Residual risks.
Additional residual risks may arise
when using the tool which may not
be included in the enclosed safety
warnings. These risks can arise
from misuse, prolonged use etc.
Even with the application of the
relevant safety regulations and the
implementation of safety devices,
certain residual risks can not be
avoided. These include:
u
Injuries caused by touching any rotating/
moving parts.
u
Injuries caused when changing any parts,
blades or accessories.
7
ENGLISH
(Original instructions)
u
Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
u
Impairment of hearing.
u
Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech
and MDF.)
Labels on tool
The following pictograms are
shown on the tool:
;
Warning!
To reduce the risk of
injury, the user must read the instruc-
tion manual.
Electrical safety
#
This tool is double insulated; there-
fore no earth wire is required. Always
check that the power supply cor-
responds to the voltage on the rating
plate.
u
If the supply cord is damaged, it must be
replaced by the manufacturer or an author-
ised Black & Decker Service Centre in order
to avoid a hazard.
Extension cables
u
A 2 or 3 core cable may be used as the
appliance is double insulated and of class II
construction.
u
Up to 30m (100 ft) can be used without loss
of power.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Heat control knob
3. Nozzle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting an accessory (g. C, D, E & F)
A selected range of accessories can be obtained from your
local retailer.
w Cone nozzle (5): Concentrates the air stream on a
smaller area.
w Fish tail (6): Spreads the air stream over a wider area
w Spoon reector (7): For soldering pipes.
w Glass protector (8): For the protection of glass during
paint stripping.
w Scraper (9): For the removal and stripping paint and
varnish.
u Fit the connecting piece of the accessory over the nozzle
(2).
Use
Setting the temperature (g. A)
u To increase the temperature setting, turn the heat control
knob (2) clockwise.
u To reduce the temperature setting, turn the heat control
knob anti-clockwise.
Switching on and off
u To switch the tool on at the low air speed, low heat, set the
on/off switch to position I.
u To switch the tool on at the high air speed, high heat, set
the on/off switch to position II.
u To switch the tool off, set the on/off switch to position O.
Using the tool
Your tool is tted with a thermostat for your safety. Using the
tool continuously for very long periods or other severe duty
cycles may cause the tool to overheat and the element to stop
working. It is therefore recommended that you allow the tool to
cool down at regular intervals during use.
u Allow the tool to heat up for a few seconds before use.
u At rst use some smoke may emit from the nozzle. This is
normal and will soon decrease.
u Use a low temperature setting for drying paint and varnish,
removing stickers, shrinking insulation tubes, and thawing
frozen pipes.
8
ENGLISH
(Original instructions)
u Use a medium temperature setting for welding plastics,
bending plastic pipes, and loosening tight nuts and
screws.
u Use a high temperature setting for removing paints and
lacquers, and soldering plumbing joints.
u If you are unsure about using this tool on a particular
material, start with a low temperature setting and perform
a test on scrap material.
Hands free use (g. B)
The tool has stand locations (4) to facilitate hands free use.
u Place the tool with the nozzle up on a surface where it
cannot be tipped over.
u Secure the cable to prevent pulling the tool off the stand
locations (4).
Warning! Always point the tool away from yourself or other
persons. Do not touch the nozzle. Take care that no material
drops into the nozzle.
Paint stripping
u Direct the hot air at the working area to heat up the paint.
u Do not burn the paint. Keep the nozzle at least 25 mm
from the surface.
u When the paint softens, remove the paint using a scraper.
Scrape the softened paint immediately or it will harden
again.
u Scrape with the grain of the wood wherever possible.
u Do not allow paint and debris to collect on the scraper.
u When scraping from a vertical position, scrape downwards
to prevent the paint from falling back into the nozzle.
u When stripping paint from a surface next to glass, take the
necessary measures to protect the glass from the heat.
Warning! Use a glass protector nozzle when stripping paint
from metal or wood framed windows.
u Dispose of all paint debris safely and make sure that the
work area is thoroughly clean after use.
Cooling down
During use, the nozzle of the tool becomes extremely hot.
After switching off, leave the tool to cool down for at least 30
minutes.
u Place the tool with the nozzle up on a surface where it
cannot be tipped over.
Maintenance
Your Black & Decker appliance has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper care
and regular cleaning of the appliance.
Warning! Switch off and unplug the appliance and allow it to
cool down before doing any maintenance on the appliance.
u Regularly clean the ventilation slots in your appliance
using a soft brush or dry cloth.
u To clean the appliance, use only mild soap and a damp
cloth. Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the appliance and never
immerse any part of the appliance into liquid.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used
again. Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker ofce at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
9
ENGLISH
(Original instructions)
Technical data
KX2001
(Type 1)
Input voltage V
ac
230
Construction
Class II
Power input W
2000
Temperature range
O
C
50 - 600
Weight kg
0.85
Guarantee
Black & Decker is condent of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker ofce at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
at www.blackanddecker.co.uk
ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/pro-
ductregistration or send your name, surname and product code to
Black & Decker in your country
.
DEUTSCH
Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!
www.blackanddecker.de/productregistration
Lassen Sie Ihr Produkt unter www.blackanddecker.de/productreg-
istration online registrieren oder schicken Sie Ihren Nachnamen,
Vornamen und den Produktcode an Black & Decker in Ihrem Land.
FRANÇAIS
N’oubliez pas d’enregistrer votre produit !
www.blackanddecker.fr/productregistration
Enregistrez votre produit en ligne sur www.blackanddecker.fr/
productregistration ou envoyez vos nom, prénom et code produit à
Black & Decker dans votre pays.
ITALIANO
Non dimenticate di registrare il prodotto!
www.blackanddecker.it/productregistration
Registrate il prodotto online su www.blackanddecker.it/productreg-
istration o inviate nome, cognome e codice del prodotto al centro
Black & Decker del vostro paese.
NEDERLANDS
Vergeet niet uw product te registreren!
www.blackanddecker.nl/productregistration
U kunt uw product online registreren op www.blackanddecker.nl/pro-
ductregistration of u kunt uw voornaam, achternaam en productcode
opsturen naar Black & Decker in uw land.
ESPAÑOL
¡No olvide registrar su producto!
www.blackanddecker.es/productregistration
Registre su producto on-line en www.blackanddecker.es/produc-
tregistration o envíe su nombre, apellidos y código de producto a
Black & Decker en su país.
PORTUGUÊS
Não se esqueça de registar o seu produto!
www.blackanddecker.pt/productregistration
Registe o seu produto online em www.blackanddecker.pt/productre-
gistration ou envie o seu nome, apelido e código do produto para a
Black & Decker no seu país.
SVENSKA
Glöm inte att registrera produkten!
www.blackanddecker.se/productregistration
Registrera produkten online på www.blackanddecker.se/productre-
gistration eller skicka namn och produktkod till Black & Decker i landet
du bor i.
NORSK
Ikke glem å registrere produktet ditt!
www.blackanddecker.no/productregistration
Registrer produktet ditt online på www.blackanddecker.no/pro-
ductregistration, eller send ditt navn, etternavn og produktkode til
Black & Decker i ditt eget land.
DANSK
Glem ikke at registrere dit produkt!
www.blackanddecker.dk/productregistration
Registrer dit produkt på internettet på: www.blackanddecker.dk/
productregistration eller send dit navn, efternavn og produktkode til
Black & Decker i dit eget land.
SUOMI
Muistathan rekisteröidä tuotteesi!
www.blackanddecker./productregistration
Rekisteröi tuotteesi verkossa osoitteessa www.blackanddecker./
productregistration tai lähetä etunimesi, sukunimesi ja tuotekoodi
oman maasi Black & Decker -edustajalle.
Ε Λ Λ Η Ν Ι Κ Α
Μην ξεχάσετε να καταχωρίσετε το προϊόν σας!
www.blackanddecker.gr/productregistration
Καταχωρίστε το προϊόν σας σε σύνδεση στη σελίδα www.
blackanddecker.gr/productregistration ή στείλτε το όνομα, επίθετο
σας και τον κωδικό πριονωτός στη Black & Decker στη χώρα σας.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

Black & Decker KX2001 Owner's manual

Category
Power tools
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI