3
4
2
1
WALL
Adapta Wall
POP-OUT WALL MOUNT
ASSEMBLY
SHEET NAME:
Ass--20018095
DRAWN BY:
SHEET 1 OF 3
REVISION: A-002
Andrew Griffiths
DRAWN BY DATE:
INSTALLATION INSTRUCTIONS
DRAWN BY:
Andrew Griffiths
DRAWN BY DATE: 20 November 2013
DRAWING NO.
to your screen using the fixings supplied. Lift the screen onto the rail of the wall assembly as 5.
shown in exploded view above.
ADJUSTING SCREENS
See diagram of arms on page 3 of 3. There is adjustment for each screen in all planes - side to side, up & down, 6.
in & out. To ensure there is enough adjustment across the array of screens we recommend temporarily hanging
the 4 corners first and checking that these screens can be levelled. If a wall is out of true where there is not
enough adjustment it may be necessary to pack out the wall assemblies.
7.
4.
INSTALLING ADJUSTABLE ARMS
Fix the 2 arms
ceiling suspended - floor to wall - free standing" installation drawing.
2
WARNING: Ensure the structure that you are attaching the wall assembly to is capable of taking 5 x the load of the
video wall including all peripherals.
NOTE: We recommend the use of a laser level to plot the horizontal datum (lines) to ensure perfect set up of the rows
and columns of screens to be installed. Templates are provided to ensure the correct spacing of the mounts for the
specific screen you are using.
Installing pop-out wall assembly
Mark and drill first mount location (see hole centre details overleaf). locate pop-out wall assembly
1
and fix 1.
using suitable anchors and fixings (not supplied).
Decide whether to install other wall assemblies horizontally or vertically. When mounting horizontally locate the 2.
2x horizontal templates
3
and locate into the slots in the sides of the fixed wall assembly
1
and into the next
wall assembly, ensuring the assembly is level. Mark and drill as before. continue this operation for the horizontal
line of screens.
To install the wall assemblies, vertically locate the 2 x vertical templates
4
and drop into the slots on the top of 3.
the fixed wall assembly
1
and into the bottom of the next wall assembly above, ensuring the assembly is level.
Mark and drill as before. Continue the two operations using the templates to build up the video wall.
To install pop-out wall mount to column mounting system, refer to "Adapta wall - video wall structure system -
PARTS LIST
ITEM NO. DESCRIPTION QTY
1 POP-OUT WALL ASSEMBLY 1
2 ADJUSTABLE SCREEN ARMS 2
3 HORIZONTAL TEMPLATE SPACER (WITH SLOT) 2
4 VERTICAL TEMPLATE SPACER (NO SLOT) 2
INSPECT THE UNIT BEFORE INSTALLING
WARNING: Watch for pinch points. Do not put your fingers between movable parts. Do not tamper with or dis-assemble.
1. Carefully inspect the mount for shipping damage. If any damage is apparent, call your carrier claims agent and do not
continue with the installation until the carrier has reviewed the damage.
NOTE: Read all instructions before starting the installation.
2. Lay out components to ensure you have all the required parts before proceeding (see parts list on page 2).
CAUTION: To prevent damage to the mount study all instructions and illustrations before you begin the installation.
Failure to do so could render the warranty for the equipment null and void. pay particular attention to the “warnings”
displayed in these instructions.
The maximum weight of screen to be installed on this mount is 45 kg (99 lb)
The mount is designed to be installed onto walls or other unicol structures. the structure to which the mount is anchored
must be capable of supporting five times the total weight of the assembled mounts and all attached equipment that
make up the complete video wall. we recommend installation by a qualified tradesperson, using masonry plugs or other
reliable fixings to ensure safe installation. consult your builder or architect if in doubt.
if you have any questions about the installation, contact unicol +44 (0) 1865 767676.
95MM
CLOSED
130MM
CLOSED
Adapta Wall
POP-OUT WALL MOUNT
Ass--20018095
DRAWN BY:
SHEET 2 OF 3
REVISION: A-002
Ricky Clark
DRAWN BY DATE:
INSTALLATION INSTRUCTIONS
DRAWN BY:
Ricky Clark
DRAWN BY DATE: 20 November 2013
OVERVIEW
SHEET NAME:
DRAWING NO.
ADAPTA-WALL
STRETCHED
FITS VESA
200X200MM
300X300MM
400X400MM
600X400MM
800X400MM
(AND ANYTHING IN BETWEEN)
ARMS TRACK IN AND OUT
VARIABLE 200-800MM
350MM
OPEN
ADAPTA-WALL
STANDARD
FITS VESA
200X200MM
300X300MM
400X400MM
600X400MM
(AND ANYTHING IN BETWEEN)
ARMS TRACK IN AND OUT
VARIABLE 200-600MM
350MM
OPEN
95MM
CLOSED
350MM
OPEN
ADAPTA-WALL
STANDARD
FITS VESA
200X200MM
300X300MM
400X400MM
400X600MM
(AND ANYTHING IN BETWEEN)
ARMS TRACK IN AND OUT
VARIABLE 200-400MM
75 225 75
TUNE ADJUSTMENT
PROVIDES IN-OUT FINE
THUMB SCREW
SECURING SCREW
TO SIDE ADJUSTMENT
ARMS HOOK TO BACK
PLATE PROVIDING SIDE
ADJUSTING
UP & DOWN
SCREW
FIX ARMS TO
SCREEN WITH
THUMB SCREW
PROVIDES IN-OUT FINE
TUNE ADJUSTMENT
Adapta Wall
POP-OUT WALL MOUNT
Ass--20018095
DRAWN BY:
SHEET 3 OF 3
REVISION: A-002
Dennis Neale
DRAWN BY DATE:
INSTALLATION INSTRUCTIONS
DRAWN BY:
Dennis Neale
DRAWN BY DATE: 20 November 2013
ADJUSTABLE ARMS
SHEET NAME:
DRAWING NO.
SCALE: 1:5
9
.30
444
8
.
1
0
1
8
300
500
800
8
R
4
POP OUT MECHANISM LOCK
PULL CORD
OPTIONAL POP OUT
MECHANISM LOCK
CAM
/
