Lightspeed Multimike User guide

Type
User guide
MULTIMIKE SET-UP AND
QUICK START INSTRUCTIONS
Lightspeed Technologies
www.lightspeed-tek.com / 800.732.8999 / 503.684.5538
USING A FLEXMIKE
3. Remove the Flexmike from the charger and place around your neck. Ensure the top
of the microphone is at the collarbone.
4. Press the power/mute button. The mic status will turn blue, indicating the
microphone is active.
5. Microphone volume may be adjusted at the microphone by using the Up/
Down buttons on the side of the Flexmike. It may also be adjusted by using the
Microphone volume knob on the front of the Multimike.
6. Plug a laptop, MP3 player or other audio device into this 3.5mm jack to wirelessly
transmit the audio signal to be played through the system.
DETERMINE SET-UP LOCATION AND PLUG IN POWER SUPPLY
1. The Multimike is generally located near
the amplifier.
2. Plug one end of the included 3.5mm cable
into the AUDIO OUTPUT connection on the
Multimike. Plug the other end into an audio
input connection on the amplifier.
QS0546US01-2
AUDIO INMICROPHONE
TONE
POWER
MIN
1
MAX MIN MA
X TREBL
E BASS
2
REGISTER
USB POWER
5V/0.2A
+
–
AUDIO IN BAL. AUDIO OUT
AUDIO OUT
MIC LINE
AUDIO OUT/DC IN
AUDIO AMPLIFIER
INPUT CONNECTION
3.5MM AUDIO CABLE
(INCLUDED)
Power / Mute
3
4
6
2
5
USING A SHAREMIKE
7. Unplug the microphone from the charger. The mic status light will turn red.
8. Press the power/mute button. The mic status will turn blue, indicating the
microphone is active.
9. Battery indicator light.
10. Plug a laptop, MP3 player or other audio device into this 3.5mm jack to wirelessly
transmit the audio signal to be played through the system.
11. Microphone volume may be adjusted at the Multimike by using the Microphone
volume knob on the front of the Multimike.
12. Up to 5 microphones may be used with a Multimike.
8
7
9
AUDIO INMICROPHONE TONE
POWER
MIN
1
MAX MIN MAX TREBLE BASS
2
10
REGISTER
USB POWER
5V/0.2A
+
AUDIO IN BAL. AUDIO OUT
AUDIO OUT
MIC LINE
AUDIO OUT/DC IN
REGISTER
USB POWER
5V/1.5A
TREBLE BASS
2
5
3. Plug the micro USB end of the power cable
into the power adapter and the other end
into the micro USB port on the back of the
Multimike. Plug the USB1 into a wall outlet.
ENSURE THE SYSTEM IS POWERED ON.
AUDIO IN
MICROPHONE
AUDIO OUT
POWER
MIN
LINK
MAX
MIN MAX MIN MAX
3
2
1. Plug the micro USB end of the power cable into the power adapter and the other end into
the micro USB port on the back of the Media Connector. Plug the USB1 into a wall outlet.
2. Press the Multimike or Media Connector power button to power on the Multimike.
3. When powered on, the blue LED will glow.
1 4
322
1
AUDIO INAUDIO OUT
REGISTER
USB POWER
5V/1.5A
TONE
TREBLE BASS
2
4
5
AUDIO INMICROPHONE TONE
POWER
MIN
1
MAX MIN MAX TREBLE BASS
2
4. Plug your laptop, MP3 player or other audio device into the Audio In 3.5mm jack on the back of the
Multimike, or into one of the input jacks on the back of the Media Connector labeled β€œAudio In”
using a 3.5mm patch cable.
5. Adjust volume at the audio source. If necessary, further volume adjustment may be made using the
Audio In volume knob on the front of the Media Connector.
USING A WIRELESS AUDIO LINK
REGISTER
USB POWER
5V/0.2A
+
–
AUDIO IN BAL. AUDIO OUT
AUDIO OUT
MIC LINE
AUDIO OUT/DC IN
AUDIO INMICROPHONE AUDIO OUT
POWER
MIN
LINK
MAX MIN MAX MIN MAX
Multimike Front
Multimike Back
Media Connector Front
Media Connector Back
2
4
For complete operating instructions, go to www.lightspeed-tek.com/MM-usermanual (or scan the 2D barcode).
USING THE OPTIONAL MEDIA
CONNECTOR WITH MULTIMIKE
SEE SET-UP INSTRUCTIONS FOR MULTIMIKE ON PREVIOUS PAGE.
NOTE: When Media Connector is paired to Multimike and powered on, a maximum of 4 microphones may be used.
2
5
1 4
322
1
AUDIO INAUDIO OUT
REGISTER
USB POWER
5V/1.5A
TONE
TREBLE BASS
1
SEE MICROPHONE INSTRUCTIONS ON PREVIOUS PAGE.
  • Page 1 1
  • Page 2 2

Lightspeed Multimike User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI