Hunter Fan 27785 Owner's manual

Brand: Hunter Fan

Model: 27785

Type: Owner's manual

Type 2 ModelsType 2 ModelsType 2 Models

Form# 42835-01

20120215

For Your Records and

Warranty Assistance

For reference, also attach your receipt or a copy

of your receipt to the manual.

__________________________________________

Model Name

__________________________________________

Model No.

__________________________________________

Date Purchased

__________________________________________

Where Purchased

English Français

Owner’s Guide and Installation Manual

 42020-01•08/01/05

42835-01•02/15/12•HunterFanCompany

YournewHunter

ceilingfanisanadditiontoyourhomeorocethat

willprovidecomfortandperformanceformanyyears.isinstallation

andoperationmanualgivesyoucompleteinstructionsforinstalling

andoperatingyourfan.

Weareproudofourwork.Weappreciatetheopportunitytosupply

youwiththebestceilingfanavailableanywhereintheworld.

Beforeinstallingyourfan,foryourrecordsandwarrantyassistance,

recordinformationfromthecartonandHunternameplatelabel

(locatedonthetopofthefanmotorhousing).

Cautions and Warnings

• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING

INSTALLATION. SAVE THESE INSTRUCTIONS.

•UseonlyHunterreplacementparts.

•Toreducetheriskofpersonalinjury,attachthefandirectlytothe

supportstructureofthebuildingaccordingtotheseinstructions,

anduseonlythehardwaresupplied.

•Toavoidpossibleelectricalshock,beforeinstallingyourfan,

disconnectthepowerbyturningothecircuitbreakerstothe

outletboxandassociatedwallswitchlocation.Ifyoucannotlock

thecircuitbreakersintheoposition,securelyfastenaprominent

warningdevice,suchasatag,totheservicepanel.

•Allwiringmustbeinaccordancewithnationalandlocalelectrical

codesandANSI/NFPA70.Ifyouareunfamiliarwithwiring,usea

qualiedelectrician.

•Toreducetheriskofpersonalinjury,donotbendtheblade

attachmentsystemwheninstalling,balancing,orcleaningthefan.

Neverinsertforeignobjectsbetweenrotatingfanblades.

•Toreducetheriskofre,electricalshock,ormotordamage,donot

useasolid-statespeedcontrolwiththisfan.UseonlyHunterspeed

controls.

Welcome

Table of Contents

1•GettingReady...................................................6

2•InstallingtheCeilingPlate..........................7

3•AssemblingtheFan.......................................8

4•SecuringtoSecondarySupport........... 10

5•WiringtheFan............................................... 11

5•InstallingtheCanopyandCanopy

 TrimRing........................................................... 12

6•AssemblingtheBlades.............................. 13

7•CompletingYourInstallationWith

 aLightFixture................................................. 14

8•OperatingandCleaning

 YourCeilingFan............................................. 16

9•Troubleshooting........................................... 17

42835-01•02/15/12•HunterFanCompany

Preparing the Fan Site

7’Minimum

Bladesto

Floor

8’Minimum

Ceiling

Height

30”From

Wallor

Nearest

Obstruction

Step 1 - Choose the Fan Site

Properceilingfanlocationandattachmenttothebuilding

structureareessentialforsafety,reliableoperation,maximum

eciency,andenergysavings.

Choose a fan site where:

•Noobjectcancomeincontactwiththerotatingfanbladesduring

normaloperation.

•efanbladesareatleast7feetabovetheoorandtheceilingis

atleast8feethigh.

•efanbladeshavenoobstructionstoairow,suchaswallsor

posts,within30inchesofthefanbladetips.

•efanisdirectlybelowajoistorsupportbracethatwillholdthe

outletboxandthefullweightofthefan.

Checklist for Existing Fan Site

Ifyouwanttouseanexistingfansite,completethefollowingchecklistto

determineifthesiteisacceptableandsafeforyournewHunterfan.Ifyou

cannotcheckoeveryitem,prepareanewfansiteasdescribedonthis

page.

Fan Support System

•Fan attaches directly to building structure.

•Fansupportsystemwillholdfullweightofthefanandlightkit.

Ceiling Hole

•eoutletboxclearanceholeisdirectlybelowthejoistorsupportbrace.

Outlet Box

•eoutletboxisanUL-approvedoctagonal4”x1-1/2”outletbox(oras

speciedbythesupportbracemanufacturer).

•eoutletboxissecuredtothejoistorsupportbracebywoodscrews

andwashersthroughtheinnerholesofoutletbox.

•eouterholesoftheoutletboxarealignedwithjoistorsupportbrace.

•ebottomoftheoutletboxisrecessedaminimumof1/16”into

ceiling.

Wiring

•eelectricalcableissecuredtooutletboxbyanapprovedconnector.

•Sixinchesofleadwiresextendfromoutletbox.

Ifyourexistingfansiteissuitable,skipaheadtoSection2 • Installing the

Ceiling Plate.

Suitable Existing Fan Site

FanSupport

System

FanSupport

System

Wiring

OutletBox

42835-01•02/15/12•HunterFanCompany

Preparing the Fan Site (continued)

CAUTION:Allwiringmustbein

accordancewithnationalandlocal

electricalcodesandANSI/NFPA70.If

youareunfamiliarwithwiring,usea

qualiedelectrician.

Steps 2 – 3

Step 4

Step 5

Step 2 - Cut the Ceiling Hole

2-1.Locatethesitefortheceilingholedirectlybelowthejoistorsupportbracethat

willholdtheoutletboxandfan.

2-2.Cuta4”diameterholethroughthedrywallorplasteroftheceiling.Youwilluse

theholetoinstallthesupportbraceandoutletbox.

Step 3 - Install a Support Brace, If Necessary

Determineifthereisaceilingjoistdirectlyabovetheceilinghole.Ifthejoististhere,

determineifitispositionedtoallowyoutorecesstheoutletboxaminimumof

1/16”intotheceiling.IfNOT,installasupportbraceasfollows:

3-1.Attacha2”x4”supportbracebetweentwojoists.Positionittoallowyouto

recessthebottomoftheoutletboxaminimumof1/16”intotheceiling.

3-2.Checkthesupportbracetoensureitwillsupportthefullweightofthefanand

lightkit.

Step 4 - Install the Outlet Box

4-1.ObtainaUL-approvedoctagonal4”x1-1/2”outletbox,plustwo#8x1-1/2”

woodscrewsandwashers,availablefromanyhardwarestoreorelectricalsupply

house.

4-2.Orienttheoutletboxsothatboththeinnerandouterholesintheboxalign

withthejoistorsupportbrace.

4-3.Drillpilotholesnolargerthantheminordiameterofthewoodscrews(5/64”)

throughtheinnerholesoftheoutletbox.

4-4.Attachtheoutletboxdirectlytothesupportbraceorjoistwithtwo#8x1-1/2”

woodscrewsandwashers.ebottomoftheoutletboxmustberecesseda

minimumof1/16”intotheceiling.

Step 5 - Prepare the Wiring

5-1.Makesurethecircuitbreakerstothefansupplylineleadsandassociatedwall

switchlocationareturnedo.Ifyoucannotlockthecircuitbreakersinthe

oposition,securelyfastenaprominentwarningdevice,suchasatag,tothe

servicepanel.

5-2.readthefansupplylinethroughtheoutletboxsothatthefansupplyline

extendsatleast6”beyondthebox.

5-3.Attachthefansupplylinetotheoutletboxwithanapprovedconnector,

availableatanyhardwarestoreorelectricalsupplyhouse.

5-4.MakecertainthewiringmeetsallnationalandlocalstandardsandANSI/NFPA

70.

Youhavenowsuccessfullypreparedyourceilingfansite.Forinstructionstoinstall

yourceilingfan,gotoyourfanmanualandcontinuewithSection2 • Installing the

Ceiling Plate.

42835-01•02/15/12•HunterFanCompany

Installer’s Choice and Optional Accessories

Understanding Mounting and Installer’s Choice®

Hunter’spatented3-positionmountingsystemprovidesyoumaximum

installationexibilityandease.YoucaninstallyourHunterfaninone

ofthreeways,dependingonceilingheightandyourpreference:Low

Prole,Standard,orAngledmounting.estepsinthismanualinclude

instructionsforallthreeInstaller’sChoicemountingmethods.

Considering Optional Accessories

ConsiderusingHunter’soptionalaccessories,includingawall-mounted

orremotespeedcontrol.Toinstallandusetheaccessories,follow

theinstructionsincludedwitheachproduct.Forquietandoptimum

performanceofyourHunterfan,useonlyHunterspeedcontrols.

Forceilingshigherthan8feet,youcanpurchase

Hunterextensiondownrods.AllHunterfansuse

sturdy3/4”diameterpipetoassurestabilityand

wobble-freeperformance.

Standard Mountinghangsfromthe

ceilingbyadownrod(included).

Angled Mountingrecommendedfora

vaultedorangledceiling

SupportBrace

Standard

Mounting

Style

Ceiling

OutletBox

SupportBrace

Ceiling

OutletBox

Angled

Mounting

Style

Low Proﬁle Mountingtsclosetothe

ceiling,recommendedforceilingsless

than8feethigh

SupportBrace

LowProle

Mounting

Style

Ceiling

OutletBox

CAUTION: To

reducetheriskof

personalinjury,attach

thefandirectlytothe

supportstructureof

thebuildingaccording

totheseinstructions,

anduseonlythe

hardwaresupplied.

42835-01•02/15/12•HunterFanCompany

Toinstallaceilingfan,besureyoucandothefollowing:

•Locatetheceilingjoistorothersuitablesupportinceiling.

•Drillholesforandinstallwoodscrews.

•Identifyandconnectelectricalwires.

•Lift40pounds.

Ifyouneedhelpinstallingthefan,yourHunterfandealercandirect

youtoalicensedinstallerorelectrician.

Gathering the Tools

Youwillneedthefollowingtoolsforinstallingthefan:

•Electricdrillwith9/64”bit

•Standardscrewdriver(magnetictiprecommended)

•Phillips-headscrewdriver(magnetictiprecommended)

•Wrenchorpliers

•Ladder(heightdependentuponinstallationsite)

Checking Your Fan Parts

Carefullyunpackyourfantoavoiddamagetothefanparts.Referto

theincludedPartsGuide.Checkforanyshippingdamagetothemotor

orfanblades.Ifanypartsaremissingordamaged,contactyourHunter

dealerorcallHunterTechnicalSupportDepartmentat866-268-1936.

Installing Multiple Fans?

Ifyouareinstallingmorethan

onefan,keepthefanbladesand

bladeirons(ifapplicable)insets,

astheywereshipped.

1 • Getting Ready

42835-01•02/15/12•HunterFanCompany

2-1. Drilltwopilotholesintothewoodsupportstructurethroughthe

outermostholesintheoutletbox.epilotholesshouldbe9/64”

indiameter.

Note:Yourfancomeswithfourpre-installedneoprenenoise

isolators.

2-2. readtheleadwiresfromtheoutletboxdownthroughthehole

inthemiddleofthehangerbracket.

2-3. Aligntheslottedholesinthehangerbracketwiththepilotholes

youdrilledinthewoodsupportstructure.Forproperalignment

useslottedholesdirectlyacrossfromeachother.Ifyouare

installingthefanonanANGLED ceiling,besuretoorientthe

hangerbracketasshowninIllustration2-3(leftorrightview).

Note:eisolatorsshouldbeushagainsttheceiling.

2-4. Placeaatwasheroneachofthetwo3”screwsandpassthe

screwsthroughtheslottedholesinthehangerbracketintothe

pilotholesyoudrilled.

  Tightenthescrewsintothe9/64”pilotholes;donotuselubricants

onthescrews.Donotovertighten.

FlatWasher

3”Screw

Steps 2-2 – 2-4

Hanger

Bracket

Isolator

Step 2-3 (Angled Ceiling Only)

CeilingPeak CeilingPeak

Large

Opening

Large

Opening

LEFT RIGHT

2 • Installing the Hanger Bracket

42835-01•02/15/12•HunterFanCompany

Youcanassembleyourfanforstandardorangled mountingasshown

insteps3-1–3-3.Forlow proﬁlemounting(ceilingslessthan8feet

high),gotosteps3-6–3-9onthenextpage.

3-1.Toassemblefantohangdownfromaatorangledceiling,place

thecanopyandcanopytrimringaroundtheadaptersothatthey

restonthefanassembly.

3-2. Feedthewiresfromthefanthroughthedownrod.

Note:Makesureallthewiresareonthesamesideofthemetal

dowelpininsidethedowrod.

3-3.Loosenthesquareheadsetscrewontheadaptertoinstallthepipe

andballassembly.Note: Whenthepipeandballassemblyisfully

installed,2-3threadsonthepipewillstillbevisible;thisisnormal.

Securelyretightenthesetscrewwithawrenchorpliers.

CAUTION:eadapterhasaspecialcoatingonthethreads.Do

notremovethiscoating;thecoatingpreventsthedownrodfrom

unscrewing.Onceassembled,donotremovethedownrod.

WARNING:Donotcarryorliftfanbycanopy.

3-4.Raisethefanandplacetheballintothehangerbracket.

3-5. Alignthenotchontheballwiththeindentinthehangerbracket.

(Rotatethefanuntilyouhearthenotchpopintoplace.)

  Goto4 • Wiring the Fan.

WARNING:Fanmayfallifnotassembledasdirectedinthese

installationinstructions.

Steps 3-4 – 3-5

Indent

Steps 3-1 – 3-3

Downrod

Canopy

Canopy

Trim

Ring

Setscrew

Adapter

3 • Assembling and Hanging the Fan

42835-01•02/15/12•HunterFanCompany

3 • Assembling and Hanging the Fan (Low Profile Only)

Youcanassembleyourfanforstandardorangled mountingasshown

insteps3-1–3-3onthepreviouspage.Forlow proﬁlemounting

(ceilingslessthan8feethigh),seesteps3-6–3-10onthispage.

3-6. Removethescrewsfromthehangerballbracket.

3-7. Placethelowprolewasherfromthepartssackintothecanopy.

3-8. Placethecanopytrimringandcanopywithwasherontopofthe

fanassembly.

3-9. Alignthescrewholesinthewasherwiththeholesintheadapter.

Assemblesecurelywiththree#8-32x3/4”screws.

3-10.Raisethefanandplacethehookonthehangerbracketthrough

theroundholeintherimofthecanopy.

WARNING:Fanmayfallifnotassembledasdirectedinthese

installationinstructions.

Step 3-10

Step 3-7 (Detail)

LowProleWasher

(NotActualSize)

Steps 3-8 – 3-9

LowProleWasher

Canopy

TrimRing

Adapter

#8-32x3/4”Screw

Step 3-6

42835-01•02/15/12•HunterFanCompany

4 • Securing Fan to Secondary Support System

4-1.Findtheloopedendofthebraidedcableandinsertitthroughthe

ceilingplateandoneoftheholesintheoutletboxintotheceiling.

4-2.Accessthesupportbraceintheceiling.Youmaynotbeabletodo

thisfrombelowtheceilingdependingonyourinstallationsite.

4-3.Driveawoodscrewandwasherintothesideofthebracethat

holdstheoutletbox.Leave3mm(1/8”)ofspacebetweenthe

supportbraceandthewasher.

4-4.Wrapthebraidedcablearoundthesupportbraceoncecreatinga

completecircle.

4-5.Hooktheloopedendofthecableoverthewoodscrewsothatthe

braidedcableliesbetweenthewasherandthesupportbrace.

4-6.Tightentheloopandsecurethescrewandwasheralltheway

downtothesupportbrace.

4-7.Coiluptheexcesscable.

4-8.Returntothefansoyoucancompletethefanwiring.

Step 4-1

3mm (1/8")

Steps 4-2 – 4-3

Steps 4-4 – 4-5

Steps 4-6 – 4-7

Support

Brace

Ceiling

OutletBox

Braided

Cable

42835-01•02/15/12•HunterFanCompany

5 •Wiring the Fan

All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualiﬁed electrician.

Wallswitchesarenotincluded.Selectanacceptablegeneral-useswitch

inaccordancewithnationalandlocalelectricalcodes.

5-1. Beforeattemptinginstallation,makesurethepowerisstillo.

5-2. Toconnectthewires,holdthebaremetalleadstogetherandplace

awireconnectoroverthem,thentwistclockwiseuntiltight.For

alltheseconnectionsusethewireconnectorsprovided.

5-3. Connectthebareorgreengroundwire(grounding)fromthe

ceilingtothegreengroundwire(grounding)fromtheceilingplate

andthegreengroundwire(grounding)fromthefan.

5-4. Connectthewhitewire(grounded)fromtheceilingtothewhite

wire(grounded)fromthefan.

5-5. Connecttheremainingwiresasfollows:

Dual Switch Wiring:

•eblackwire(ungrounded)fromtheceilingtotheblackwire

(ungrounded)fromthefan

•eblackwirewithawhitestripe(ungrounded)fromthefan

tothewire(ungrounded)forthewallswitch

Single Switch Wiring:

•eblackwire(ungrounded)fromtheceilingtotheblack

(ungrounded)andtheblackwirewithawhitestripe

(ungrounded)fromthefan

CAUTION:Besurenobarewireorwirestrandsarevisibleafter

makingconnections.

5-6. Turnthewireconnectorsupwardandpushthemcarefullyback

throughtheceilingplateintotheoutletbox.

5-7. Spreadthewiresapart,withthegroundedwiresononesideof

theoutletboxandtheungroundedwiresontheothersideofthe

outletbox.

Wire

Connector

42835-01•02/15/12•HunterFanCompany

6 • Installing the Canopy and Canopy Trim Ring

6-1.Partiallyinstalltwocanopyscrews(about2fullturns)inthe

hangerbracket.

6-2.Raisethecanopyoverthehangerbracket.Alignpartiallyinstalled

screwswithkeyslotsincanopy.

6-3. Twistcanopyclockwisetosecure.

6-4.Installthird&fourthcanopyscrewinroundholeoncanopy.

Securelytightenallfourscrews.

6-5. Usingbothhands,pushthecanopytrimringuptothetopofthe

canopy.

6-6. Twistcanopytrimringclockwisetosecurethecanopy.

Should you need to remove the canopy

trim ring, follow these steps:

 1.Twistcanopytrimringcounter

clockwiseuntilitreleasesfrom

canopy.

Steps 6-1 – 6-2

CanopyTrim

Ring

Canopy

HangerBracket

Step 6-3

Canopy

Screw

Step 6-4

Step 6-5

42835-01•02/15/12•HunterFanCompany

7 • Assembling the Blades

Hunterfansuseseveralstylesoffanbladeirons(bracketsthatholdthe

bladetothefan).

7-1. Yourfanmayincludebladegrommets.Ifyourfanhasgrommets,

insertthembyhandintotheholesontheblades.

7-2. Attacheachbladetoabladeironusingthreebladeassembly

screws.Ifyouusedgrommets,thebladesmayappearslightlyloose

afterscrewsaretightened.isisnormal.

7-3. Removetheblademountingscrewsandrubbershippingbumpers

fromthemotor.Note:Someblademountingscrewsareinstalled

inthemotortosecureshippingblocks.

7-4. Foreachblade,insertoneblademountingscrewthroughthe

bladeiron,andattachlightlytothefan.Insertthesecondblade

mountingscrew,thensecurelytightenbothmountingscrews.

Step 7-1 (Detail)

BladeAssembly

Screws

Usewithgrommet

Usewithoutgrommet

Grommet

Blade

Mounting

Screw

Steps 7-1 – 7-2

Step 7-4

42835-01•02/15/12•HunterFanCompany

WARNING:Useonlythelightxturesuppliedwiththisfanmodel.

8-1. Toattachtheupperswitchhousing,partiallyinstalltwo#6-32x

3/8”housingassemblyscrewsintotheswitchhousingmounting

plate.

8-2. Feedtheupperplugconnectorthroughthecenteropeningofthe

housing.

8-3. Alignthekeyholeslotsinthehousingwiththehousingassembly

screws.

8-4. Turnthehousingcounterclockwiseuntilthehousingassembly

screwsarermlysituatedinthenarrowendofthekeyholeslots.

Installtheremaining#6-32x3/8”screwintothehousing.Tighten

allthreescrewsrmly.

CAUTION:Makesuretheupperswitchhousingissecurelyattached

totheswitchhousingmountingplate.Failuretoproperlyattachand

tightenallthreeassemblyscrewscouldresultintheswitchhousingand

lightxturefalling.

8-5. Toattachthelowerswitchhousing,connecttheupperplug

connectorfromthemotortothelowerplugconnectorinthe

lowerswitchhousingassembly.

Note:Bothplugconnectorsarepolarizedandwillonlyttogether

oneway.Makesuretheconnectorsareproperlyalignedbefore

connectingthem.Incorrectconnectioncouldcauseimproper

operationanddamagetotheproduct.

8-6. Placethelowerswitchhousingassemblyovertheupperswitch

housing.Alignthesidescrewholesintheupperandlowerswitch

housings.Attachthelowerswitchhousingtotheupperswitch

housingwiththree#6-32x3/8”housingassemblyscrews.

Steps 8-1 – 8-3

Housing

Assembly

Screw

8 • Installing the Light Kit

Housing

AssemblyScrew

LowerSwitch

Housing

Plug

Connector

Plug

Connector

Detail

Steps 8-5 – 8-6

Upper

Switch

Housing

42835-01•02/15/12•HunterFanCompany

8-7. Removetheplasticfromeachoftheshades.

8-8. Installtheshades.

8-9. InstallfourTypeB10lightbulbs(40Wattmaximumeach).

Steps 8-8 – 8-9

Shade

LightBulb

8 • Installing the Light Kit (continued)

Remove the protective wrap

fromthesilhouetteonthe

motorhousingbeforestarting

thefan.

Note: IncompliancewithCanadianfederalenergyregulations,this

ceilingfancontainsadevicethatrestrictsitslightoutput.

ExceedingthewattagelimitmarkedontheMAXwattage

stickeraxedtothelightsocket(s)mayresultinrehazard

orimproperoperation.

42835-01•02/15/12•HunterFanCompany

9 • Operating and Cleaning Your Ceiling Fan

In warm weather,use

downwardairowpattern

In cold weather,useupward

airowpattern

9-1. Turnonelectricalpowertothefan.

9-2. efanpullchaincontrolspowertothefan.epullchainhas

foursettingsinsequence:High,Medium,LowandO.

• Pullthechainslowlytochangesettings.

• Releaseslowlytopreventthechainfromrecoilingintothe

blades.

• echainusesabreakawayconnectorthatseparatesifthe

chainisjerked.Ifthishappens,simplyreinsertthechaininto

theconnector.

9-3. elightpullchaincontrolsthepowertothelightxture.e

chainhastwosettings:ONandOFF.

9-4. Ceilingfansworkbestbyblowingairdownward(counterclockwise

bladerotation)inwarmweathertocooltheroomwithadirect

breeze.Inwinter,havingthefandrawairupward(clockwiseblade

rotation)willdistributethewarmerairtrappedattheceiling

aroundtheroomwithoutcausingadraft.

9-5. Forcleaningnishes,useasoftbrushorlint-freeclothtoprevent

scratching.Avacuumcleanerbrushnozzlecanremoveheavier

dust.Removesurfacesmudgesoraccumulateddirtanddustusing

amilddetergentandaslightlydampenedcloth.Youmayuse

anartisticagent,butneverabrasivecleaningagentsastheywill

damagethenish.

9-6. Cleanwoodnishbladeswithafurniturepolishingcloth.

Occasionally,applyalightcoatoffurniturepolishforadded

protectionandbeauty.Cleanpaintedandhigh-glossbladesinthe

samemannerasthefannish.

To Change Airﬂow Direction

Turnthefanoandletitcometoacomplete

stop.Slidethereversingswitchonthefantothe

oppositeposition.Restartfan.

Reversing

Switch

42835-01•02/15/12•HunterFanCompany

Problem: Nothing happens; fan does not move

1.Turnpoweron,replacefuse,orresetbreaker.

2.Loosencanopy,checkallconnectionsaccordingtothewiringthe

fansection.

3.Checktheplugconnectionintheswitchhousing.

4.Pushmotorreversingswitchrmlyleftorrighttoensurethatthe

switchisengaged.

5.Pullthepullchaintoensureitison.

6.Removetheshippingbumpers.

Problem: Noisy operation

1.Tightenthebladeassemblyscrewsandbladeironarmaturescrews

untilsnug.

2.Checktoseeifthebladeiscracked.Ifso,replacealltheblades.

Problem: Excessive wobbling

1.Ifyourfanwobbleswhenoperating,usetheenclosedbalancingkit

andinstructionstobalancethefan.

2.Tightenallbladeironscrews.

3.Turnpowero,supportfanverycarefully,andcheckthatthe

hangerballisproperlyseated.

Problem: Lights turn oﬀ when installed or dim when turned on

1.Checktomakesurethewattageandtypeoflightbulbsinstalled

matchthespecicationsonthelightsocket.

Problem: Lights shut oﬀ suddenly

1.Turnthepowertothefanoatthewallswitch.Wait30seconds,

thenresumepowertothefan.

Ifyouneedpartsorserviceassistance,pleasecall

888-830-1326(InCanada,call866-268-1936)or

visitusatourwebsiteat

http://www.hunterfan.com.

HunterFanCompany

7130GoodlettFarmsParkway#400

Memphis,Tennessee38016

10 • Troubleshooting

Hunter Fan 27785 Owner's manual

Brand: Hunter Fan

Model: 27785

Type: Owner's manual

Download PDF

report

Hunter Fan 27785 Owner's manual

Hunter Fan 27785 Owner's manual

Related papers

Other documents