Crane EE-9003 Double Electric Breast Pump Owner's manual

Brand: Crane

Model: EE-9003 Double Electric Breast Pump

Category: Breast pumps

Type: Owner's manual

This manual is also suitable for

EE-9003

Crane Double Electric Breast Pump

EE-9003

PLEASE READ AND SAVE ALL INSTRUCTIONS TO ENSURE

THE SAFE AND EFFECTIVE USE OF THIS BREAST PUMP.

If you have any questions about the operation of your breast

pump, please contact Crane Customer Care.

Toll Free: 888-599-0992

Email: customer-service@crane-usa.com

https://crane-usa.com/product-registration/

SAVE YOUR DATED PROOF OF PURCHASE!

[ You will need this in case of warranty ]

Congratulations on choosing the Crane Double Electric Breast

Pump. The Crane Double Electric Breast Pump is designed to

mimic a baby’s natural sucking. Use it to express your milk

efficiently in whisper quiet comfort. The soft silicone breast

cushion and easily adjustable modes help to stimulate milk let

down, while gently massaging and squeezing the breast and

nipple.

Cleaning, caring for and using your pump is a breeze with the

built-in rechargeable battery, fully enclosed system with anti-

backflow and easy to assemble 2-piece silicone soft breast

shield and milk collection sets.

Design for Better Living.

TABLE OF CONTENTS

Safety Instructions

Pg. 4-5

Functions and Features

Pg. 6

Parts

Pg. 7-8

Assembling Your Crane Pump

Pg. 9-10

Cleaning, Hygiene, and Care

Pg. 11-13

Button and Display Guide

Pg. 14

Ready To Pump

Pg. 15-16

Milk Storage

Pg. 17

Troubleshooting & Customer Care

Pg. 18-21

Find Your Fit & Technical Information

Pg. 21-23

IMPORTANT SAFETY INSTRUCTIONS

This is a single user product, use by more than one person can present

health risk and performance questions and will void the warranty.

WARNING! READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

When using this pump and other electrical products, basic safety precautions

should always be maintained, including the following:

DANGER: To reduce the risk of electrocution

• ALWAYS unplug electrical product immediately after use.

• DO NOT USE while bathing.

• DO NOT place or store this product where it can fall into a tub or sink.

• DO NOT place in or drop into water or other liquid.

• DO NOT reach for product if it has fallen into the water. Unplug

immediately

• NEVER immerse pump unit or AC adaptor in water or attempt to

sanitize in a microwave

WARNING: To reduce the risk of burns, electrocution, fire or injury to persons:

• Use this product only for its intended use as described in these

instructions.

• Breast pumps are personal care items for one user only.

• Danger of electrocution! Keep the device dry, never immerse in water

or other liquids. Do not run water over the pump

• Keep the power adaptor away from heated surfaces.

• Do not reach for product if it has fallen into water. Unplug immediately

• Do not use outdoors with AC adaptor, or operate where aerosol spray

products are being used, or oxygen is being administered.

• Close supervision is necessary when being used near children

• Do Not allow small children to play with the pump unit, accessories, AC

adaptor, etc. These parts may cause a choking or strangulation hazard.

Keep pump and all accessories out of REACH OF CHILDREN.

• DO NOT use attachments not recommended by the manufacture.

• Do NOT use this product if it is broken or any parts are missing.

• Do not use while bathing or showering.

• Never operate this product if it has a damaged cord or plug, if it has

been dropped or damaged or is any parts are broken or missing.

• Do not use while sleepy or drowsy

• Do not place product in direct sunlight

• Do not drop, hit, or insert any object into any opening or tubing

• Do not touch the product or parts with bare hands after boiling to avoid

scalds and burns.

SAVE THESE INSTRUCTIONS!

GENERAL SAFETY INSTRUCTIONS

WARNING! Read and understand all instructions. Failure to follow

these instructions and safety guidelines can lead to harm or injury from

the device and may also damage the pump and kit.

The warnings, cautions and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may

occur. It must be understood by the user that common sense and caution

area factor that cannot be built in this product but must be supplied by

the user.

• This is a single user product. Use by more than one person may present a health risk.

• Use the electric breast pump only for its intended use as described in this manual.

• You should not experience discomfort or pain when using your Crane breast pump.

Use the suction level and settings that are within your own comfort level. If you

experience discomfort or pain, stop using the device and contact your professional

lactation consultant, care provider or Crane representative.

• Do not use the electric breast pump while sleeping or overly drowsy.

• Supervision is required when electric breast pump is used in the vicinity of children.

• Unplug the AC adapter from wall socket outlet when the pump is not in use and store

out of reach of children.

• AC Adaptor charger included with the Crane Double Electric Breast Pump is 110-240V

50/60Hz and can be used worldwide, however, in some countries you may need to

use an outlet adaptor.

• Do not leave your Crane Double Electric Breast Pump unattended while plugged in.

• Do not operate the electric breast pump if it is damaged or showing signs of

excessive wear. This includes the plug and power cord too.

• Do not use 3rd party accessories, attachments or fittings with your Crane pump.

• Do not place the electric breast pump near any appliances generating a strong

magnetic field.

• Do not use near concentrated oxygen or pressurized gases

• Do not drive while pumping.

• Inspect all pump components before each use.

• Do not thaw frozen breast milk in a microwave or a pan of boiling water.

• Clean and sanitize all parts that come into contact with breast/breast milk prior to

first use.

• Wash all parts that come into contact with your breast/breast milk after each use.

• If you experience any pain or discomfort of the breast or nipple, stop using the breast

pump and consult your lactation consultant or physician immediately.

THIS PRODUCT IS INTENDED FOR PERSONAL USE ONLY

Introduction

Functions & Features

Your Crane breast pump has the following functions and features:

• Double sided pumping: Your pump includes everything you need for double

pumping. Pumping from both sides at once saves you time and supports

better milk supply.

• A fully closed system with anti-backflow.

• Ergonomic milk collection kit: Silicone 3D Cushions allow for a more

comfortable fit and help to apply gentle pressure, better suction and

massage action to stimulate lactation while pumping.

• 2-Phase expression- Stimulation and Expression

• 9 Adjustable suction levels

• Control in your hands: With a flexible range of modes, levels and dual

pumping options, the Crane double electric breast pump lets you find the

ideal pumping combination.

• Touch control: Easy use and & wipe clean controls

• 30 min count-up timer: Time your current pumping session up to half an

hour.

• All parts are BPA Free.

• Portable, compact design: Gives you and baby more flexibility to pump

whether at home or on the go. Your Crane double electric breast pump

comes complete with a built in rechargeable li-ion polymer battery.

Parts

Other available parts

The Silicone 3D cushions fit around the nipple and come in a range of sizes, you’ll

find the most commonly used size in your Crane breast pump box. Your nipple

will expand while milk is being expressed. If you find the standard sized Silicone

3D cushion is too small or too large, other sizes are available from your Crane

retailer. See the back of the instructions for information on how to measure your

nipple for the correct sized cushion.

Assembling Your Crane Pump

MILK Collection Kit

(3D Cushion, Breast Shield, Diaphragm and Diaphragm Cap)

Insert the silicone 3D cushion into the breast shield

body. Ensure the edge of the 3D cushion

Is attached to the breast shield body.

Secure valve

Once the silicone 3D cushion is inserted

Into the breast shield body, gently push

Upwards on the valve to make sure it is

Securely attached to the inside body of

The breast shield.

Diaphragm and Cap

Carefully insert the diaphragm into the

top of the breast shield body. Make sure

the edge is flush and the seal is good.

Screw the cap on tightly to prevent

Any air from leaking.

Assemble the Bottle

Place the assembled breast shield body

onto the bottle. Screw the bottle onto

the breast shield body.

Connecting the Pump Unit to

the Milk Collection Kit

Insert the tubing connector into the air vent

on the diaphragm cap. Insert the other end

of the tubing into the left side of the pump

unit.

If you are double pumping, connect the 2

tubing into the 2

milk Collection kit and

insert the tubing into the left side of the

pump unit.

Ensure the tubing is securely connected to

the pump unit and the milk Collection kits.

Connecting the Pump Unit to Power

To Connect to the power supply, plug the A/C adaptor into the wall outlet.

Attach the power cord to the right side of the pump unit.

Li-ion Polymer Battery Power Supply/Charging

Your Crane Double Electric Breast Pump can operate on built-in battery or power

outlet. The built-in rechargeable battery charges fully after about four and a half

hours. Do not charge for more than 6 hours. From a full charge your pump can

work continuously for about 2 hours.

When the AC adapter is not connected, switch to the ON position on the bottom

of the unit to use the built-in battery to supply power. When the battery power

is low, battery indicator will flash to indicate the battery needs to be charged.

Charging the battery before it is fully drained will protect the li-ion polymer

battery. When the battery is fully charged, it will stop charging automatically to

avoid damage to the li-ion polymer battery.

Cleaning, Hygiene & Care

How to keep your pump clean

Follow the instructions for cleaning, caring and storing for your Crane breast

pump and parts. Failure to do so may pose a health risk and void the warranty.

Your Crane pump kit is designed for single use only, it is not intended for multiple

users. Every mother should have their own pump kit. Use multiple users risks

the spread of transmissible diseases.

Make sure to wash your hands with soap and warm water prior to touching the

breast pump and the breast pump parts. Avoid touching the inner parts of the

milk collection kit parts which come in to contact with breast milk. The motor

unit must never be exposed or immersed into water or other liquids for cleaning.

The motor unit must not be Sterilized in a microwave sterilizer.

Bottles:

Bottles should be sterilized after every use with babies under 3 months of age.

Wash and sanitize the Bottle Kit before your first use. Sterilize daily and wash

after each use.

Milk Collection Kit:

Wash and sanitize the Milk Collection Kit before your first use. Sanitize daily and

wash after each use. The breast pump milk collection kit has a closed system

therefore cleaning the tubes is not necessary. If you happen to see moisture in

the tubes alter pumping, remove the tubes from the breast shields. Turn on the

motor for a few minutes until the moisture is gone.

Pump unit:

Wipe pump unit with clean damp cloth. Sterilize the unit using a disinfectant

wipe and wipe off the outside of the tubing and the tubing jack (where tubing

attaches to the pump unit). NEVER submerge the pump unit in water or use in a

sterilizer.

First time using your breast pump

Carefully read this instruction manual before using your Crane Double Electric

Breast Pump. Failure to follow these instructions and safety guidelines can lead

to harm or injury from the device and may also damage the pump and kit.

• Wash your hands with soap and warm water.

• Disassemble all parts that come into contact with the breast/breast milk:

Breast shield body, silicone cushions & diaphragms & bottles & bottle parts

NOTE: silicone cushion comes assembled onto the breast shield.

• Sterilize these parts using by boiling for 3-5 minutes or with another

sterilization technique. See ‘STERILZING YOUR PUMP PARTS’ for more

information.

• Leave to dry or dry with a clean cloth or paper towel.

STERILIZING YOUR PUMP PARTS

BEFORE FIRST USE AND ONCE DAILY

1. Place disassembled breast shield, silicone cushions, diaphragm,

bottle and bottle parts that are safe to boil into a pot and cover

with water. DO NOT BOIL TUBES AND CONNECTORS.

2. Put the pot over the heat and bring to a boil.

3. Boil for 3-5 minutes.

4. Allow water to cool and gently remove items with clean tongs

5. Do not boil tubes or connectors

6. Allow to air-dry thoroughly. Place sanitized pump parts and

bottle brush on a clean, unused dish towel or paper towel in an

area protected from dirt and dust. Do not use a dish towel to

rub or pat items dry because doing so may transfer germs to the

items.

7. Store dry parts in a cool, clean place when not in use. DO NOT

store wet or damp parts.

Before Each Use

Wash your hands well with soap and water and dry thoroughly before touching

any part of your pump.

• Make sure that all parts are totally dry prior to use. Wet or damp parts will

cause poor suction.

• Once all parts are totally dry, re-assemble the milk collection kit.

• Make sure that you check for wear and tear on tubes, plastic and silicone parts.

• Replace worn out or damaged parts immediately as this will affect suction.

CLEANING THE TUBES

The Crane Double Electric Breast Pump is a closed system, therefore cleaning the

tubes is not necessary. If you see moisture in the tubes after pumping, remove

the tubes from the breast shields. Turn the unit on for a few minutes until the

moisture is gone.

TUBE CARE for Moisture in the tubes

If you see still moisture in the tubing:

• Wash tubing in warm, soapy water.

• Rinse with clean water

• Shake out water droplets and hang to dry.

After each pumping session

• Rinse each part that has come into contact with the breast and/or breast milk

immediately after pumping. Parts that come into contact with the breast and

breast milk are; bottles, breast shield body, silicone 3D Cushions, diaphragm. This

avoids buildup of milk residue in the collection kit bottles/parts and growth of

any bacteria.

• Wash all parts above in warm soapy water using any fragrance-free mild liquid

dishwashing detergent. This degreases the parts of the milk collection kit. Grease

residue affects suction and passage of milk into the collection bottles.

• Use a separate cleaning sponge and bottle brush with a smaller brush to reach

the tiny nooks of the collection kit parts.

• Rinse each piece thoroughly with warm water for 10 to 15 seconds.

• You may sanitize the parts through a sterilization method after each use.

• Parts may become damaged or deform if exposed to high temperatures for any

more than 5 minutes.

• Make sure that you check on wear and tear on tubes and plastic or silicone

parts.

• Replace worn out or damaged parts immediately as this will affect suction.

• Allow to air-dry thoroughly. Place sanitized pump parts and bottle brush on a

clean, unused dish towel or paper towel in an area protected from dirt and dust.

Do not use a dish towel to rub or pat items dry because doing so may transfer

germs to the items.

• Make sure that all parts are totally dry prior to use. Wet or damp parts will

cause poor suction. Once all parts are totally dry, re-assemble the milk collection

kit.

You will need to re-assemble your milk collection kit after each cleaning. Before

assembling, the parts which directly come in to contact with breast milk must be

cleaned and sterilized before each use. These parts include; the milk bottle,

Silicone 3D Cushions, breast shield body, diaphragm and bottle lid.

Button & Display Guide

How to use the buttons on your pump unit

1. Power – turn unit in and off when

plugged into an outlet

2. Mode Function - Touch the button

to select Right (R), Left (L) or Dual (D)

(right and left breast simultaneously).

3. Phase Function (stimulation/expression

phase Icons)- press this to change between

functions. Tap to cycle through the different expression phases. There

are 2 phase options for pumping, each phase is represented by these

icons on the display when selected.

Stimulation phase: mode massages the nipple and areola to encourage

effective letdown on the left and right breast simultaneously (Dual

Mode).

Expression phase: Slower motion with deeper suction simulates infants

natural sucking motion. In the expression phase you can select Right

Breast, Left Breast or Dual mode by pressing the Mode Icon.

In the expression phase you can adjust the level of suction for each

breast. To adjust the level of suction, press the Mode Icon to the

desired side you want to adjust the suction level. Then press + or – to

set the desired suction level. Repeat the same steps for the other

side. Press the Mode icon again and the pump will be in the Dual

mode with the set levels of suctions for each side

4. +/- increase and decrease suction- press + to increase and – to decrease

suction in each function.

5. Level (Setting) of suction indicator (1-9 levels)

6. Battery Power Indicator- Flashes when low battery.

7. Timer- Unit turns off after 30-minute cycle.

Preparing to pump

So, your pump is clean, sterilized, assembled and you’ve familiarized yourself

with the controls. Now it’s time to start pumping.

Be prepared - Make sure you have everything you need for the 30 minutes or so.

Have a glass of water and a snack in arms reach a cloth for any spills. Do you

have your phone charged, or something else to read, watch or listen to.

You can do this! Take a breath and relax. Whether this is your first time using

your pump or you’ve done it many times…just take a moment to relax, think

about your baby and know you’ve got this.

See & hear your baby - Many moms find that pumping is more successful if they

have the right sensory cues. Watching a video or seeing a picture of your baby

may be enough to help your milk let down. Listening to a recording of your baby

or having an item of clothing that has their smell may also help to get your milk

flowing.

The power of routine - Your body will also respond to the familiarities of how

and where you pump, so expressing at the same times of day helps your body

know what is expected.

Get comfortable – Pumping where you normally feed your baby can be a good

cue for your body. Try to choose a chair or position that takes care of your neck

and back. Supporting your breast with a cushion may help too, particularly if you

are expressing from both breasts at once and need a hand free.

Using Your Crane Pump

Remove the dust cover – Always remove the dust cover before you start to

pump.

Position the breast shield - Massage around your breast, then position your

nipple in the center of the silicone 3D cushion.

Pumping Mode - Switch on your pump, starting with the stimulation mode icon

encourage letdown. Once your milk begins to flow (usually after a couple of

minutes), switch to an expression mode icon

Finding the right settings for you:

• When using your pump for the first few times, experiment with the different

expression setting (-/+) to find the one that works well for you.

• If your milk flow begins to drop, you may find it helpful to gently massaging

your breast.

• Adjust the suction level gradually to one that is effective but still comfortable.

Don’t choose a level that’s too high and uncomfortable.

• You may find it helpful to switch between the Expression icon and stimulation

icon Phases while you are pumping.

How long to pump - Use your pump to express your milk until the breast is

empty, which is usually between 15-30 minutes.

Finishing your pumping session - When you are ready to stop expressing,

switch your Crane pump off. Ensure the pump motor is OFF before removing

the milk collection kit from your breasts.

Time to clean - Please see the instructions for rinsing and washing or sterilizing

your pump parts that have come in contact with your breast or breast milk.

Wipe your pump unit.

Double Pumping

As you learn to use your Crane Pump, you may find it easier to pump one side at

a time to begin with. Once you are confident with positioning the breast shield

and have an understanding of the controls, you can be more confident using

both sides at once. Pumping both sides at once can help increase your milk

supply as well as reduce the time needed to pump.

A cushion under one breast can help you still have one hand free to have a drink

or hold something to read. Hands free expressing bras can free up your hands if

you want to move about while you are pumping from both breasts.

Milk Storage

Storing & Using Breast Milk

Please check the latest advice on storing and using thawed breast milk with your

physician or lactation consultant.

Always keep your stored breast milk in a sterilized bottle or sterile milk storage

bag, adding the date if you are planning to freeze it. Breast milk can be kept at

room temperature for 4 hours.

You can store your breast milk in the fridge for up to 48 hours at 2-4 degrees C.

Choose the coldest part of the fridge, such as above the vegetable drawer, not in

the door. Your breast milk can be stored for up to 3-6 months in a freezer. Fill

your storage bag or bottle no more than ¾ full, as the frozen milk will expand.

Allow your frozen breast milk to defrost itself in the fridge. When it is thawed,

use it straight away.

Your baby might like warm milk. Stand the bottle in a container of hot water and

let it heat to body temperature before feeding. Microwaving bottles is not

recommended because the uneven heating can burn your baby’s mouth, and the

heat can damage the food value and health protecting qualities of breast milk.

Once warmed, and before feeding, always swirl the container of the milk to mix

well and test the temperature by shaking a few drops of milk on the inside of

your wrist. The milk should feel just warm on your skin.

Human Milk Storage Guidelines

CRANE CUSTOMER CARE

CALL US: 888-599-0992 (Mon-Fri 9:00am – 4:00pm CST)

EMAIL US: [email protected]

LIVE CHAT: available at www.crane-usa.com

Quick Troubleshooting Guide

DO NOT attempt to repair the Breast Pump yourself.

If the breast pump continues to not operate, please contact Crane

Customer Care.

Cause

Solution

Low Suction

• Air Leakage of connecting parts

(valve, cushion, tubing, or

connector).

• Pump unit’s air circulator is

blocked. Tubing is bent or residue

left in tubing.

• Check each part, make sure

connections are on correctly

and securely.

• Untangle tubing.

• Clean or replace tubing if

needed.

No Suction

• Valve is not assembled in correct

place or the valve is deformed

and damaged.

• Ensure valve is securely

attached to the breast shield

body.

No Power

• The AC adaptor Is not plugged

into the main socket or the DC

socket on the pump unit

• The rechargeable battery is flat

• Ensure AC Adaptor is

plugged in to the wall outlet

and the DC socket on the

unit.

• Charge the battery.

Milk or Water in Tubing

• Diaphragm is not correctly

positioned or is damaged

• Stop immediately. Clean,

reposition, or replace the

diaphragm before pumping. Dry

or replace tubing before

pumping.

Display Shows E1 or E2 Alarm

• E1: Open Circuit

• E2: Short Circuit

• Please contact your Crane

Customer Care.

Troubleshooting

Weak Suction or No Suction

All the instructions below must be followed. Failure to follow any of these

instructions will lead to weak suction or no suction vacuum at all.

• All parts must be totally dry and not damp.

• Frequent use or improper sterilization method can cause aging on Silicone 3D

Cushions. If the Silicone 3D Cushions have aged and are worn out, replace

immediately.

• Make sure that the Silicone 3D Cushions on each collection kit fit tightly onto

the breast shield body. The Silicone 3D Cushions have edges that should fit

perfectly across the cushion edges.

• If the Silicone 3D Cushions are not snugly attached this will result in poor

suction.

• Make sure that the silicone diaphragm is properly attached to the breast shield

body.

• Check that all connections are tight so as not to cause any air to leak. Check

that tubing is not wet, damp, bent or twisted.

• Tubing must be straightened and uncoiled to ensure proper air flow.

• If you notice any milk residue, clean the tubing and air dry. (Follow proper

cleaning the tubes instructions described in this manual)

• If you notice any water condensation or milk inside the tubing, clean and air

dry.

• Tubing must always be dry and checked prior to each use. Wet or damp tubing

will cause poor suction.

• Worn out tubing with holes will cause a reduction in suction. Replace

immediately when worn out.

• Check to make sure that the breast shield is well secured and tightly fastened

to the tubing connector.

• Check that tubing connector ends are tight and well connected to the tubing,

the breast motor unit and the breast shield.

Page is loading ...

Crane EE-9003 Double Electric Breast Pump Owner's manual

Brand: Crane

Model: EE-9003 Double Electric Breast Pump

Category: Breast pumps

Type: Owner's manual

This manual is also suitable for

EE-9003

Download PDF

report

Crane EE-9003 Double Electric Breast Pump Owner's manual

This manual is also suitable for

Crane EE-9003 Double Electric Breast Pump Owner's manual

Related papers

Other documents