PRO
MCD 708
Quick Start Guide
What’s in the Box?
You should find these items upon opening the box.
2
User Manual
1
Quick Start Guide
Quick start guide
User manual
Composite video and audio
cables
(yellow, white, red)
Remote control with two
AAA batteries
FM and MW antennas
Control Cable
SCART Cable
MCD708 QUG_Eng-22 2006.10.27, 16:201
Tips
– Refer to the User Manual for other TV
connection options.
–For connecting to a Progressive Scan
TV, refer to the user manual for proper
connections and detailed setup.
1
2
4
3
Setting up the TV
1
2
Press SOURCE (or DISC on the remote control) to select disc source.
Swith on the TV and set it to the correct Video In channel.
5
Connect the speaker cables.
Connect the MW and FM antennas.
Connect the control cable.
Connect the SCART cable to the TV.
Connect the power cords of the system and TV.
AUDIO
IN
S-VIDEO
IN
VIDEO IN
TV IN
AUDIO
IN
S-VIDEO
IN
VIDEO IN
TV IN
SUB WOOFER
LINE OUT
O
OFER
4
5
1
2
2
3
1
AC power
FM antenna
MW antenna
Speaker
(right)
Speaker
(left)
MCD708 QUG_Eng-22 2006.10.27, 16:202
Setting the clock
1
2
3
4
In standby mode, press and hold CLOCK/RDS on the remote control.
When the hour digits flash, turn VOLUME-/+ on the system or press VOLUME+/- on the
remote control to set the hours.
Press CLOCK/RDS again and the minute digits flash. Then turn VOLUME-/+ on the
system or press VOLUME+/- on the remote control to set the minutes.
Press CLOCK/RDS again to confirm the time settings.
Setting DVD menu options
IMPORTANT!
For instances whereby the progressive scan feature is activated but the connected
TV does not support progressive signals, or when the cables have not been
appropriately connected, refer to the User Manual for proper progressive scan
setup or deactivate the progressive scan feature as below:
1) Turn off the TV progressive scan mode or turn on the interlaced mode.
2) Press SYSTEM on the remote control to exit the system menu, then press DISC
to exit progressive scan.
Tip
Refer to chapters "Getting Started" and "System Menu Options" in
the User Manual for detailed descriptions.
MCD708 QUG_Eng-22 2006.10.27, 16:203
Playing a disc
1
2
3
4
Press OPEN •CLOSEç (or ç on the remote control) to open the disc tray and load
disc, press the same button again to close the disc tray.
Load disc with the label side facing up.
Playback starts automatically. If not, pressÉÅ.
To stop playback, press PRESET-/9 (or 9 on the remote control).
Programming and tuning to radio stations
1
2
3
Press SOURCE (or TUNER on the remote control) to select tuner source.
Press PROG on the remote control for more than two seconds to program all available
stations in order of waveband.
Press PRESET+/- (or CH +/- (¡ / ™) on the remote control) until the desired preset
station is displayed.
PDCC-JS/JW-0539
2005 C Koninklijie Philips Electronics
N.V. All rights reserved.
http://www.philips.com
GB
Tip
Detailed playback features and
additional functions are described in the
User Manual.
Notes for remote control:
– Select the source you wish to control by
pressing one of the source select keys on the
remote control (DISC or TUNER, for example).
– Then select the desired function (
2;
,
í
,
ë
for example).
OPENÄCLOSE
MCD708 QUG_Eng-22 2006.10.27, 16:204
-
1
-
2
-
3
-
4
Philips MCD708/05 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Philips MCD290/79 User manual
-
-
-
-
-
-
-
Philips MCM309R/37 User manual
-
-