Saluki Technology NS1102X User manual

Brand
Saluki Technology
Model
NS1102X
Type
User manual

Saluki Technology NS1102X is a navigation signal simulator that can generate GNSS signals with various configurations and scenarios. It has a wide range of applications, including:

  • GNSS receiver testing
  • GNSS antenna testing
  • GNSS system simulation
  • GNSS signal jamming and anti-jamming testing

The NS1102X can simulate GPS, BDS, Galileo, and GLONASS signals. It can also simulate multiple constellations simultaneously. The signal power can be adjusted from -60dBm to 150dBm.

The NS1102X has a user-friendly interface that allows you to easily configure the simulation parameters. You can also use the software to control the simulator remotely.

Saluki Technology NS1102X is a navigation signal simulator that can generate GNSS signals with various configurations and scenarios. It has a wide range of applications, including:

  • GNSS receiver testing
  • GNSS antenna testing
  • GNSS system simulation
  • GNSS signal jamming and anti-jamming testing

The NS1102X can simulate GPS, BDS, Galileo, and GLONASS signals. It can also simulate multiple constellations simultaneously. The signal power can be adjusted from -60dBm to 150dBm.

The NS1102X has a user-friendly interface that allows you to easily configure the simulation parameters. You can also use the software to control the simulator remotely.

NS1102X Navigation Signal Simulator
Installation Manual
2
Contents
1. Introduction and Installation of Hardware...................................................... 3
1.1 Simulator Panel...........................................................................................3
1.1.1. Front Panel......................................................................................3
1.1.2. Rear Panel.......................................................................................3
1.2 Installation Connection...............................................................................4
2. GNSS Control Software..................................................................................5
3
1. Introduction and Installation of Hardware
1.1 Simulator Panel
1.1.1. Front Panel
Figure 1-1 Front panel of the simulator
As shown in the Figure 1-1, there are:
1) RF signal output port：1;
The simulation signal generated by the simulator is
output from this port. Output power ranger：-60dBm to -
150 dBm.
2) Signal status：2；
3) Power switch:1;with indicator light .
1.1.2. Rear Panel
Figure1-2 Rear panel of the simulator
As shown in the Figure1-2, there are:
1) COM port：1；
2) Reset：1；
4
3) Lan port：1；
4) Three-phase power port：1；
5) 1PPS Input：1；
6) 1PPS Output：1；
7) 10MHz Input：1；
8) 10MHz Output：1.
1.2 Installation Connection
Note: make sure that the simulator power switch is disconnected before installation.
Figure1-3 shows the basic connected diagram for the installation
between the simulator and the computer and user equipment.
Figure 1-3 Schematic diagram of simulator installation connection
Connect the three-phase power port with AC power supply through
the power cord before using the simulator. The RF output port of the
5
simulator is connected to the users through the RF coaxial cable.
Note: the maximum power of the RF output is -60dBm.
2. GNSS Control Software
The computer has been installed with the control software. And the
IP address has been configured (the IP address is configured as
10.129.41.x,where x is the number between 1 - 254 except 1 - 12).
After being connected as shown in the Figure 1-3, the control software
can be used directly.
Please refer to the instruction for the specific.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Saluki Technology NS1102X User manual

Brand
Saluki Technology
Model
NS1102X
Type
User manual

Saluki Technology NS1102X is a navigation signal simulator that can generate GNSS signals with various configurations and scenarios. It has a wide range of applications, including:

  • GNSS receiver testing
  • GNSS antenna testing
  • GNSS system simulation
  • GNSS signal jamming and anti-jamming testing

The NS1102X can simulate GPS, BDS, Galileo, and GLONASS signals. It can also simulate multiple constellations simultaneously. The signal power can be adjusted from -60dBm to 150dBm.

The NS1102X has a user-friendly interface that allows you to easily configure the simulation parameters. You can also use the software to control the simulator remotely.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents