2. Opera
  3. Signature Bed 8 Inch Extension Platform
Signature Bed 8 Inch Extension Platform

Opera Signature Bed 8 Inch Extension Platform User guide

  • Hello! I have reviewed the Installation and User Guide for the Opera Signature 8" Extension Platform. This guide provides detailed instructions on how to install the extension platform to your Opera Signature Profiling bed, including steps for attaching footboard extensions and side panels. I am ready to help with any questions about this product.
  • What is the Opera Signature Bed 8” Extension Platform designed for?
    What bed is the extension platform compatible with?
    What should I do if I have issues during installation?
Installation and User
Guide
VISIT OPERABEDS.COM | CALL 0333 222 8584
Enhancing Lives,
Delivering Comfort
OPERA® SIGNATURE BED
8” EXTENSION PLATFORM
1 | Opera Beds | Opera Signature Bed 8” Extension Platform Installation and User Guide | Version 1
(B) Extension Platform x 1
Contents
2. Installation and Commissioning
Before you begin! Read this Installation Guide conscientiously before
installing the Signature Bed Extension Platform.
(A) Footboard Extension
Bracket x 2
(D) 20cm Side Skirt Infill x 2
(E) M6 Side Skirt Screw x4
(C) M6 Extension Platform
Screw x4
1. General Information and Safety
The Opera Signature Bed 8” Extension Platform is designed to extend the
Opera Signature Profiling Bed by 200mm (8”) for taller users.
The Opera Signature Bed 8” Extension Platform is designed to be used with
the Opera Signature Profiling beds. Opera will not be liable for any hazards,
injury or damage arising from using the extension platform incorrectly or with
a dierent bed.
Any incidents or issues must be reported to Opera at, support@operabeds.
com.
operabeds.com | 0333 222 8584 | 2
1. Remove Footboard
Remove the side rails by loosening the bolts on the side of the footboard and
placing the side rails onto the floor. Loosen the bolts (a) under the Signature
Profiling Bed chassis using an allen key and pulling out the footboard. Set
the footboard on the floor. Remove the two T-brackets on the footboard by
unscrewing the screws.
1. Remove the side rail screw and
lower side rails.
2. Loosen bolts and remove
headboard.
3. Remove T-brackets by removing
the screws.
aa
3 | Opera Beds | Opera Signature Bed 8” Extension Platform Installation and User Guide | Version 1
2. Re-attach the Footboard
Place the longer T-bracket (A) over the holes and feed the screws through to
secure in place. Take the extension platform (B) and slide it all the way into the
T-brackets. Screw the extension platform screws (C) into the holes at the bottom
of the extension platfom to fix it into place. Align the footboard with the mattress
platform and slide into place. Tighten the securing bolts on both sides with an
allen key.
1. Screw the longer T-brackets onto
the footboard.
2. Fix the extension platform onto the
T-brackets.
3. Slide the footboard into the
mattress platform.
4. Tighten the bolts with an allen
key.
operabeds.com | 0333 222 8584 | 4
3. Attach Side Panel
Line up the additional side skirt infill (D) panel and tighten the side skirt screw (E)
using an allen key.
5 | Opera Beds | Opera Signature Bed 8” Extension Platform Installation and User Guide | Version 1
Notes
operabeds.com | 0333 222 8584 | 6
Notes
7 | Opera Beds | Opera Signature Bed 8” Extension Platform Installation and User Guide | Version 1
Azure House, Connaught Road, Kingswood, Hull, HU7 3AP
0333 222 8584 | support@operabeds.com | operabeds.com
Version 1 | Published in October 2022
/