Saunalife EE8G is a premium barrel sauna designed to provide a relaxing and rejuvenating sauna experience in the comfort of your own home. Built with high-quality materials and craftsmanship, this sauna offers a range of features to enhance your sauna sessions. The full glass front allows you to enjoy panoramic views while unwinding, creating a serene and spa-like ambiance. The sauna is made from durable and heat-resistant materials, ensuring longevity and optimal performance.
Ergo-Series EE8G Barrel Sauna
Full Glass Front 79D" x 90H"
Note: Please read manual before construction Rev: (1.0)7/2023
Front & Back Walls
66.92" x 8.87" x 3.75"
70.86" x 1.62"
78.73" x 4.71" x 1.62"
78.73" x 1.62"
74.40" x 27.17"
74.40" x 1.75" x 1.75"
30.75" x 1.75" x 1.75"
29.56" x 1.68" x .75"
72.87" x 1.68" x .75"
L=~17.25"
78.73" x 11.75" x 1.62"
78.73" x 1" x 1.62"
78.73" x 1.18" x 1.62"
78.73" x .75" x 1.62"
78.73" x .37" x 1.62"
78.73" x 2" x 2"
EE8G Barrel Sauna 79D" x 90H" Details list. 1
6.68" x 1.75" x 1.75"
10c
x6
10a
x4
12a
x4
70.62" x 20.68" x 3.93"
10
x2
69.68" x 15.14" x 3.56"
11
x2
12
x2
14
x1
15b
x2
15a
x2
15c
x2
15d
x1
34.25" x 3.46" x 1.12"
30.31" x 1.62" x 1.12"
3.46" x 1.62" x 1.12"
E
C
L=~9.87"
D
.18" x 3.50"
(x50)
H
I
J
.12" x 1.50"
(x90)(x35)(x190)
K
.12" x 1.25"
~330(x15)
L
M
Torx bits
T10 T15
T20 T25
Bit PH2
(x2)
(x4)
(x4)
25" x 1.75" x 1.75"
9.87" x 1.75" x 1.75"
70.62" x 8.18" x 3.50"
68.50" x 28.31" x 2.87"
25.59" x 3.46" x 1.12"
EE8G Barrel Sauna 79D" x 90H" Details list. 2
.18" x 2"
.15" x 2.25"
Silicone gun
(Only glass-wall models)
Front glass wall installation
Thickness 1.06"
Thickness .62"
Use piece of wood to
protect plywood
Apply waterproof
silicone to the groove
Baseframe 1.06"
86.61" x 3.75" x 1.12"
x1
~.07"
~.07"
~.07"
Use piece of wood to
protect plywood
Coverframe .62"
Front glass wall installation
min. .78"
Please be careful!!!
Do not hit the glass
with the screw.
~.90"
DET U
Fix it diagonally to make wall
more rigid during the installation.
Please be careful!!!
Do not hit the glass
with the screw.
Front glass wall installation
Wooden back wall assembly
Pre-drill holes .15"
before screws.
Pre-drill holes .15"
before screws.
Diagonal measurements should be equal
EE8G Barrel Sauna 79D" x 90H"
Position
cradles inside
grooves of
stave 2
Center stave 2 on
cradle 1
EE8G Barrel Sauna 79D" x 90H"
EE8G Barrel Sauna 79D" x 90H"
Drill 4 holes .50"
through DET 2
outsid
e
Fix temporarily to
support walls.
~.25"
IMPORTANT! Be sure to leave
a .25”gap when tightening screws
to leave room for adjustment when
the outer bands (B) are installed.
Check walls installation
manual on extra pages!
Sauna wall configuration
depends on Your model!
EE8G Barrel Sauna 79D" x 90H"
Use strap to support
boards during installation
IMPORTANT! Be sure to leave a .25”
gap when tightening screws to leave
room for adjustment when the outer
bands (B) are installed.
EE8G Barrel Sauna 79D" x 90H"
If needed, trim the flat edge of the
board to create the desired width.
Fasten the two halves using
proper size screws
Raise slightly before installing
the combined board
Join two boards together (as shown in
diagram II) that will bridge the width of
the "A" gap. It is recommended that
the combined boards are
approximately .25" wider than the gap.
EE8G Barrel Sauna 79D" x 90H"
~9.43"
~5.87"
Place the bands around
the barrel on the outer
side of the cradle.
EE8G Barrel Sauna 79D" x 90H"
I
Remove all
temporary braces
3x DET F
1x DET G
Upper vent
Lower vent
6x K
6x K
2x DET 10
4x DET 10a
II
12x J
III
Front wall side is
with endboard.
Back wall side is
without endboard.
A
B
A
B
EE8G Barrel Sauna 79D" x 90H"
Pre-drill holes .12"
Use level for
installation of benches
Pre-drill holes .12"
Fix screw at slight angle, be
careful to not hit the glass.
Fasten the opposite
sides in the same way!
EE8G Barrel Sauna 79D" x 90H"
18.57"
4.64"
EE8G Barrel Sauna 79D" x 90H"
Cut from this side if needed!
If Your sauna heater is smaller, You
can cut DET 15a to size, that suits
with Your heater.
EE8G Barrel Sauna 79D" x 90H"