REXING X5 User guide

无线充电器

出风口夹子

Type-C充电线

说明书

*1可调节吸盘支架

Wireless charger Air vent mount

Type-C cable User manual

Adjustable suction cup mount

尊敬的用户：

感谢您购买本产品，为了确保您获得可靠的售后服务，请认真阅读

以下说明：

Air vent mount

Suction cup holder

Direction for use

球头连接部件

可360°旋转

压下紧锁支架与吸盘

支撑臂角度调节

松紧旋钮

无线充角度调节

松紧旋钮

支撑臂

可180°调整

平面安装吸盘

The components

connected to the bulb

can rotate 360°

Holder and suction

mount locking switch

Arm angle

adjusting knob

Angle adjustment

knob

The holder arm

can be adjustable 180°

Suction mount

（产品两侧按键可以任何一键夹持或者张开夹臂。）

6、停车熄火，产品停止供电时，如果手机还在支架上，支架会在2

秒内发出连续报警5次提醒用户取下手机。（产品内置超级电容断电5

分钟内可按侧键打开夹臂取出手机。）

将吸盘放置于合适的平面位置，调整角度按下按键使吸盘紧锁平面。

固定后可随意调节角度和前后距离。TPU吸盘+滴胶双重吸附，一键

即锁紧。

1、把该产品与任意一配件通过球头螺帽装配并旋紧（可兼容其他球

头直径17mm配件），并固定在理想位置。用数据线把产品QC3.0车

充（选配）连接，并插入点烟器取电。

2、该产品通电后，环形指示灯会显示带呼吸效果的蓝灯，左右伸缩

夹臂会在5秒后自动张开等待放置手机；通电后产品如果不亮蓝灯（

不亮灯、闪烁或亮其他颜色灯均表示产品有问题，请停止使用并退回

销售商处理）。

3、为了保证充电的效率和稳定性，放上手机前先通过调节支架的

底托档位尽量让手机背面中心位置尽量对准支架面板上的

“Rexing”符号，不同尺寸大小的手机应对应不同的档位。无线

充的最佳距离是6mm以内并不能穿透金属，所以需要避免用金属的

或太厚的（大于3mm）手机保护壳，这样才能保证手机快速的无线

充电。

4、放上手机后左右夹臂会自动夹住手机，如果手机支持QI无线充

电协议,产品会同时启动无线充电，产品无线充电启动时指示灯会带

呼吸效果的绿光；如果手机不支持无线充电，指示灯蓝绿交替闪烁5

秒后灯灭。本产品最大充电功率为15W，充电效率根据充电环境和手

机会有所不同。

5、产品通电运行过程中，可通过产品两侧触摸按键任意一键张开

夹臂取下手机；取下手机后，指示灯即刻显示蓝灯待机状态。

5. When the product is powered on, you can open the clamp

arms by pressing any button on both sides of the product to

remove the phone; after removing the phone, the indicator

will immediately show a blue light standby state. (The

buttons on both sides of the product can be clamped or

opened with any one key.)

6. When the product is turned off and the product stops

supplying power, if the mobile phone is still on the holder, the

holder will issue an alarm 5 times within 2 seconds to remind

the user to remove the mobile phone. (The built-in super

capacitor is powered off for 5 minutes.You can press the side

button to open the arm to take away the phone. )

Adjust the position of the top piece of the air outlet and

the rotatable clip assembly according to the position of the air

outlet blade; insert the blade and select the lock switch

position according to the thickness of the blade; suitable for

one-key locking of the air outlet of most cars. Silicone touches

the car, tighter and fits better to protect the car from

scratches.

Place the suction cup on a suitable flat position, adjust the

angle and press the button to lock the suction cup firmly onto

the flat surface. After fixing, the angle and the front-to-back

distance can be adjusted at will. TPU suction cup + glue double

adsorption, one key to lock.

1. Assemble the product and any accessory through a ball

head nut and tighten it (compatible with other ball head

diameter 17mm accessories), and fix it in an ideal position.

Connect the product to the QC3.0 car charger (optional)

with the data cable, and insert to the cigarette lighter to get

electricity.

2.After the product is powered on, the ring indicator light

will turn on blue breathingly, and the left and right

telescopic arms will automatically open after 5 seconds to

wait for the mobile phone to be placed; if the product does

not turn on red after power on (not turn on, flash or turn on

other color lights) All indicate that there is a problem with

the product, please stop using it and return it to the seller

for processing).

3. In order to ensure the efficiency and stability of charging,

before putting the phone on, adjust the bottom bracket

position of the stand and try to align the center position of

the back of the phone with the " Rexing " symbol on the

stand panel as much as possible. Cell phones of different

sizes should correspond to different Stalls. The best

distance for wireless charging is within 6mm and cannot

penetrate metal, so it is necessary to avoid using metal or

too thick (greater than 3mm) mobile phone protective

shells to ensure fast wireless charging of mobile phones.

4. After placing the phone, the left and right clamping

arms will automatically clamp the phone. If the phone

supports QI wireless charging protocol, the product will

start wireless charging at the same time, and the indicator

light turns green breathingly when the product wireless

charging starts; if the phone does not support wireless

charging, the indicator light green and blue flash alternately

for 5 seconds and then the light goes out. The maximum

charging power of this product is 15W, and the charging

efficiency will vary according to the charging environment

and mobile phone.

Package

Functional component

Speciﬁcations

可调节底托

球头螺帽

夹臂

夹臂控制

触摸按键

产品名称：X5 无线充车载支架

输入要求：QC3.0车充适配器

输出功率：15W(支持10W\7.5W\5W)

充电距离：≤6mm

适用手机：4.7-6.9英寸

screw cap

indicator

light

touching

button

指示灯

Adjustable bottom bracket

compatible with

根据出风口叶片位置调整好出风口顶片和可旋转夹子组件的位置；插

入叶片，根据叶片厚度选择锁紧开关档位；适用于大部分汽车出风口

一键锁紧。硅胶接触汽车，更紧更贴合更好保护汽车不刮伤。

温馨提示：

以上小型圆形款式的出风口,夹子不能完美适配。

通过按压调节夹子

可旋转的夹子配件

可调节的出风口支撑

Quick Start Guide

使用说明书

Dash Cam

Wireless Car Holder/Charger

Model - X5

Wireless Car Holder/Charger

Model - X5

Download the Manual

https://www.rexingusa.com/support/

product-support/

REXING X5 User guide

Related papers

Other documents