EVannex Y Mud Flaps User manual

Brand: EVannex

Model: Y Mud Flaps

Type: User manual

EVannex Y Mud Flaps are designed to shield the lower body panels of your Tesla Model Y from road debris and protect against damage caused by mud, rocks, and other road hazards. Simple to install yourself with basic tools, the kit includes replacement push screws and fasteners to ensure a secure fit. The mud flaps seamlessly integrate with your Tesla's sleek design and are available in a range of colors to complement your vehicle's exterior.

EVANNEX® ••• Tesla Aftermarket Accessories ••• evannex.com

Disclaimer: EVANNEX is not responsible for any vehicle damage caused during the installation or use of this product.

Any costs associated with any vehicle damage are the sole responsibility of the purchaser.

INSTALLATION INSTRUCTIONS

Mud Flaps for Tesla Model 3 and Model Y

Please read these Installation Instructions BEFORE you install EVANNEX Mud Flaps. Detailed video installation

instructions can be found at evannex.com.

EVANNEX Mud Flaps have been designed to protect the lower body panels of your Model 3 or Model Y from road debris.

Installation of EVANNEX Mud Flaps is a relatively straightforward DIY project. However, if you’re uncomfortable with the

installation for any reason, we recommend that you contact a professional installer and have them do the installation for

you.

INSTALLATION

Tools required: A small, flat head screw driver, a 10mm socket and socket wrench, a

cleaning cloth

Installing Front Mud Flaps

Step 1. Turn your wheel and tire so that you’ll be able to access the appropriate

wheel well area.

Step 2. Clean the area around the OEM fasteners (see photo) in the rear area of the

wheel well.

Step 3. Using the small flat head screw driver, pop the center push screw of both

of the OEM fasteners on the inside of the wheel well. Using the flat head, raise the

push screw and pop it out along with the expansion fastener. Don’t become concerned if

the push screw or the fastener breaks. You are provided with replacement push screws

and fasteners (see photo).

Step 4. Snap the mud flap into place aligning the holes in the mud flap with the

OEM holes in the wheel well.

Step 5. Push the expansion fastener clip and push screw provided into the OEM

hole in the wheel well. There are two (2) holes in the front wheel well.

Step 6. Repeat steps 1 though 5 for the other front wheel well.

Installing Rear Mud Flaps

Step 1. Clean the area around the OEM fasteners in the rear area of the wheel

well.

Step 2. Using the small flat head screw driver, pop the center push screw of the

single OEM fastener on the inside of the wheel well. Using the flat head, raise the

push screw and pop it out along with the expansion fastener. Don’t become concerned

if the push screw or the fastener breaks. You are provided with replacement push

screws and fasteners.

Step 3a (for Model 3): Using the 10mm socket and socket wrench, remove the 10

mm bolt on the bottom of the fender near the edge of the wheel.

Step 3b (for Model Y): Do NOT remove the 10 mm bolt on the bottom of the

fender. The 10 mm mounting tab should be placed on top of the OEM bolt. Push down

on the tab to seat it in place.

Step 4. Snap the mud flap into place aligning the holes in the mud flap with the

OEM hole in the wheel well (see photo).

Step 5. Push the expansion fastener clip and push screw provided into the OEM

hole in the wheel well. There is one (1) hole in the rear wheel well.

Step 6. For Model 3 only, place the 10mm bolt through the hole on the bottom of

the Mud Flap and then using the 10mm socket and socket wrench, replace the

10 mm bolt on the bottom of the fender near the edge of the wheel well.

Step 7. Repeat steps 1 though 6 for the other rear wheel well.

Your mud flaps are now installed.

EVannex Y Mud Flaps User manual

EVannex Y Mud Flaps User manual

EVannex Y Mud Flaps User manual

Other documents