M-Elec's updated slim batten now integrates a snap on diffuser to make the fit off process
that much faster and more flexible. Upgraded larger terminal blocks are utilised adding to the
convenience. Rear entry and additional internal space simplifies cable routing. External CCT
switch allows the user to pick the right lighting and change it depending on the conditions without
opening the fitting. A 60cm and 120cm size will suit most applications. Comes standard with
M-Elec's 5 year warranty.
Product information
*Total power consumed including driver
** Average life is calculated on expected average lifespan
TECHNICAL INFORMATION
T. 1300 222 445 | www.melec.com.au melec.com.au/legal/warranties
Slim Batten
Total Power: 20W* 40W*
MAX Lumen Output:
WW 1700lm
NW 1900lm
W 1800lm
WW 3400lm
NW 3800lm
W 3600lm
Colour Temp:
WW 3000K
NW 4000K
W 6000K
IP20
90lm/w
80
Beam Angle: 120°
Dimmable: No
Integrated driver
Average Life: 36000hrs**
Operating current at
Connection
Construction
Dimensions: 600x 83.5x36.5mm 1200x83.5x36.5mm
Weight: 0.4kg 0.78kg
5 years
T. 1300 222 445 | www.melec.com.au melec.com.au/legal/warranties
INSTALLATION GUIDE
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
• Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
• Disconnect power before installing or servicing
• This fitting is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures
• Do not extend low voltage cables from the output of power supply
• All components must not be mechanically stressed
• Be careful not to damage or destroy conductive paths on the circuit board
• 000)
• Correct electrical polarity must be observed as the wrong polarity may destroy the product and is not covered under warranty
• Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against
corrosive agents such as moisture, condensation and other harmful elements
1. Turn power off before commencing installation.
2. Remove the diffuser by un-screwing the end cap (without
CCT switch) and the pulling the diffuser up.
3. Place the base against the wall or ceiling and use suitable
4.
5. Reinstall the diffuser and the end cap
6. Select the desired colour output on the end cap
containing the CCT switch.
7. test according to all applicable standatd and
requriements.
L N
3000K (WW)
4000K (NW)
60
ONSITE WARRANTY
EXCLUSIVE TO
MEMBERS ONLY
FREE
MEMBERS ONLY
MEMBERS ONLY
F
F
R
R
E
E
E
E
O
O
N
N
S
S
I
I
T
T
E
E
W
W
A
A
R
R
R
R
A
A
N
N
T
T
Y
Y
F
F
O
O
R
R
3
3
Y
Y
E
E
A
A
R
R
S
S
I
I
N
N
C
C
L
L
U
U
D
D
E
E
S
S
P
P
A
A
R
R
T
T
S
S
&
&
L
L
A
A
B
B
O
O
U
U
R
R
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
I
I
n
n
c
c
o
o
n
n
j
j
u
u
n
n
c
c
t
t
i
i
o
o
n
n
w
w
i
i
t
t
h
h
y
y
o
o
u
u
r
r
s
s
t
t
a
a
n
n
d
d
a
a
r
r
d
d
p
p
r
r
o
o
d
d
u
u
c
c
t
t
w
w
a
a
r
r
r
r
a
a
n
n
t
t
y
y
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
M-ELEC M-ELEC ML-VLPS-D150 VALO 24V Dimmable Power Supply User manual
-
Thomson Lighting TASGU103K6,8F38 Datasheet
-
HANECO VSL20W06-TRI Installation guide
-
Chauvet Onair User manual
-
-
Enttec ALEPH2 ET Mk2 User manual
-
ProLights ECLPANELTWCJR User manual
-
Enttec ALEPH 2 ET User manual
-
Elation KL PANEL User manual
-
