SetupGuide
Comfort
call
DECT
SD Series
Instruction Manual
SD Series – Setup Guide | 1
Contents “Setup Guide”
Contents “Setup Guide”
Important safety information ....................................................................... 2
Scope of delivery and overview of the SD series ........................................ 3
Base stations with components ................................................................... 3
Headsets with components .......................................................................... 4
Product overview of the base stations ........................................................ 5
Overview of the front ..................................................................................... 5
Overview of the rear ...................................................................................... 5
Overview of the bottom ................................................................................ 6
Setting up the base station ........................................................................... 7
Connecting the base station to the mains power supply ....................... 7
Connecting the base station to a fixed line phone .................................. 8
Connecting the base station to an optional
electronic hook switch control (EHS) ........................................................10
Connecting the base station to a computer ............................................11
Charging the headset ...................................................................................12
Testing the headset system and the sound quality ................................ 14
Adjusting the headset system using the DIP switches .........................14
Adjusting the audio signal by means of the dial tone ..........................16
Adjusting the volume ..................................................................................17
Adjusting the automatic audio transmission “Auto Audio” ................17
If a problem occurs ....................................................................................... 18
Specifications ................................................................................................ 19
Important safety information
2 | SD Series – Setup Guide
Important safety information
왘 Please read this instruction manual carefully and completely before
using the product.
왘 Always include this instruction manual when passing the product on to
third
parties.
왘 Do not use an obviously defective product.
Pr
eventing damage to health an
d accidents
왘 Do not listen at high volume levels for long periods of time to prevent
hearing damage.
왘 Always
maintain a distance of at least 3.94” (10 cm) between the ear
cups
and the cardiac pacemaker or implanted defibrillator since the
product generates permanent magnetic fields.
왘 Keep the product, accessories and pac
ka
ging parts out of reach of chil-
dren and pets to prevent accidents and choking hazards.
왘 Do not use the product in situations which require special attention.
Preventing damage to the product and malfunctions
왘 Always keep the product dry and do not expose it to
extreme tempera-
tures (hairdryer, heater, extended exposure to sunlight, etc.) to avoid
corrosion or deformation.
왘 Only use attachments/accessories supplied or recommended by
Sen
nheiser.
왘 On
ly clean the product with a soft, dry cloth.
왘 Unplug the power supply unit from the wa
ll socket
to completely
disconnect the product from the mains power supply.
왘 Do not short-circuit the contacts of the
product. Make sure that no
metal objects (e.g. paper clips, hair pins, earrings) come into contact
with the interfaces and contacts.
왘 Only use the base station for charging SD series headsets.
Intended use/Liability
The headset system can be used for calli
ng and – together with a computer
(VoIP) and/or a telephone – for audio input/output and is intended for
professional office or call center use.
It is considered improper use when this product is used for any application
not named in this instruction manual.
Sennheiser does not accept liability for damage arising from abuse or
misuse of this product and its attachments/accessories. The risk is to be
borne by the user.
Sennheiser is not liable for damages to USB devices that are not consistent
with the USB specifications.
Sennheiser is not liable for damages resulting from the loss of connection
due to flat or overaged rechargeable batteries or exceeding the DECT
transmission range.
The US base stations operate on special transmission frequencies whose
use is not authorized outside the United States.
왘 Do not use the SD BS US base station outside the United States.
Scope of delivery and overview of the SD series
SD Series – Setup Guide | 3
Scope of delivery and overview of the
SD series
The SD series allows you to combine base stations (BS) and headsets (HS)
to meet your needs. The listed headsets and base stations are compatible
with each other. The SD series base stations marked with ML in their name
are opt
imized for Microsoft
Lync
™
.
The scope of delivery includes – depending on the product purchased –
a base station and/or a headset with corresponding components.
Base stations with components
SD BS for fixed line phone and computer
SD BS ML for fixed line phone and computer, opti
mized for Micro-
soft Lync
SD BS USB for computer
SD BS USB ML for computer, optimized for Microsoft Lync
SD BS Phone for fixed line phone
Safety
Guide
Quick
Guide
Phone
USB
SD BS USB
SD BS USB ML
SD BS Phone
SD BS
SD BS ML
Phone
USB
Scope of delivery and overview of the SD series
4 | SD Series – Setup Guide
Headsets with components
SD Office – HS monaural, with different wearing styles
SD Pro1 – HS monaural, with headband
SD Pro2 – HS binaural, with headband
SD Pro1 – HS
SD Pro2 – HS
SD Office – HS
Quick
Guide
Product overview of the base stations
SD Series – Setup Guide | 5
Product overview of the base stations
Overview of the front
Overview of the rear
쐃 PC button with LED
쐇 Charging contacts
쐋 Link LED
쐏 Phone button with LED
쐄 Charge status LED
SD BS
SD BS ML
SD BS Phone
SD BS USB
SD BS USB ML
쐃
쐇
쐏
쐄
쐋
쐏
쐃
쐂 Phone socket
쐆 Handset socket
쐊 ACC socket
쐎 DC IN socket
쐅 PC socket (USB)
SD BS
SD BS ML
SD BS Phone
SD BS USB
SD BS USB ML
P
C
DC
Ph
o
ne
H
ea
d
set
A
C
C
쐂
쐊
쐆
쐅
쐎
Product overview of the base stations
6 | SD Series – Setup Guide
Overview of the bottom
쐈 DIP switch row 1 to 6
쐉 Set button
씈 Microphone volume control
씉 ABC switch
SD BS
SD BS ML
SD BS Phone
SD BS USB
SD BS USB ML
쐈
씈
쐉
씉
Setting up the base station
SD Series – Setup Guide | 7
Setting up the base station
You can use the headset system with your fixed line phone and/or your
computer. The base station controls the wireless communication to the
headsets.
왘 Place the base station at a minimum distance of 15 cm
from the fixed
line phone.
Connecting the base station to the mains power supply
1 Connect the connector of the power supply unit to the DC IN socket
(marked yellow). Connect the power supply unit to a wall socket.
2 The Link LED lights up red.
Disconnecting the base station from the mains power supply
왘 If the product is not used for extended periods of time, unplug the
pow
er supply unit from the wall socket.
1 2
SD BS
SD BS ML
P
C
DC IN
o
ne
Head
s
e
t
ACC
Setting up the base station
8 | SD Series – Setup Guide
Connecting the base station to a fixed line phone
왘 Check which connection possibility is best suited for your telephone.
왘 Follow the instructions in the corresponding chapter.
Connecting the base station to a fixed line phone without headset socket
1 Disconnect the handset cable from the telephone and connect it to the
Handset socket (marked gray) on the base station.
2 Connect the telephone cable to the handset socket on the telephone
and to
the Phone socket (marked green) on the base station.
3 Use a pointed object (e.g. a ball pen) to set the DIP switches 1 and 2 to
the position show
n.
Connection possibilities Page
Connection to a fixed line phone without headset socket 8
Connection to a fixed line phone with headset socket 9
Connection to an optional mechanical handset lifter 9
A
B
C
A
2
1
3
PC
D
C
P
h
o
n
e
He
a
d
s
et
A
CC
D
C
P
h
o
n
e
He
a
d
s
et
A
CC
DC IN
Setting up the base station
SD Series – Setup Guide | 9
Connecting the base station to a fixed li
ne phone with headset socket
1 Connect the telephone cable to the headset sock
et on the telephone
and to the Phone socket (marked green) on the base station.
2 Use a pointed object (e.g. a ball pen) to set the DIP switches 1 and 2 to
the position
shown.
Connecting the base station to an optional
mechanical handset lifter
The Sennheiser HSL 10 II mechanical handset lifter is an optional accessory
available from
your Sennheiser partner. The handset lifter allows you to
answer calls even when you are away from your desk.
왘 Connect the base station to the fixed line phone as described in
ch
ap
ter .
왘 Connect the handset lifter to the ACC socket on the base station.
왘 Connect the handset lifter to the fixed
line phone. F
or more informa-
tion, refer to the instruction manual of the HSL 10 II handset lifter.
B
1
P
C
D
C
Ph
on
e
H
e
a
d
s
et
A
C
C
2
D
C
Ph
one
H
ea
d
se
t
AC
C
C
A
P
C
D
C
P
h
on
e
H
e
a
d
s
et
A
C
C
PC
A
C
C
Setting up the base station
10 | SD Series – Setup Guide
Connecting the base station to an optional electronic
hook switch control (EHS)
The necessary EHS connection cables as well as adapter cables for manu-
facturer specific standards are available as optional accessories from your
Sennheiser partner. The corresponding quick guides are supplied with
the cables or can be found on the product page on our website at
www.sennheiser.com/cco.
By way of example of a Siemens and an Alcatel adapter cable, the following
describes how to connect the base station to an electronic hook switch.
1 Connect the base station to the fixed line phone.
2 Use a pointed object (e.g. a ball pen) to set the DIP switch to the posi-
tion shown.
Siemens, Agfeo, Aastra, Auerswald, etc.
Al
ca
tel
For an overview of the available connection and adapter cables, visit
the SD series product page on our website at
www.sennheiser.com/cco or contact your Sennheiser partner.
1
2
P
C
D
C
P
ho
n
e
H
e
a
d
se
t
A
CC
P
C
D
C
P
ho
n
e
H
e
a
d
se
t
A
CC
1
2
Setting up the base station
SD Series – Setup Guide | 11
Connecting the base station to a computer
왘 Connect the USB cable to the PC socket (marked orange) on the base
station and to a USB socket of your computer. The operating system
detects the USB audio device ”Sennheiser DECT” and installs the neces-
sary drivers.
Sennheiser PC software
The free Sennheiser PC software allows you to add value to your
Sennheiser products. The
Sennheiser Updater, for example, facilitates easy
updating of products with new software. For more information, visit our
website at www.sennheiser.com/cco/software.
PC
D
C
P
h
on
e
H
e
a
d
se
t
A
C
C
P
C
DC
H
e
ad
s
e
t
A
C
C
P
C
Charging the headset
12 | SD Series – Setup Guide
Charging the headset
Charge the rechargeable battery for at least 20 minutes without interrup-
tion before using it for the first time. A complete charging process takes
about 60 minutes.
Charging the headset using the base station
왘 Place the headset into the magnetic holder of the base station.
The Headset LED
lights up blue and the rechargeable battery is being
charged. The Charge status LED on the base station indicates the
charge status.
During the first charging process, it may take up to 5 minutes until the
Headset LED lights up blue.
LED segment
(white = lit up)
Required
charging time
Corresponds to a talk time of
Wideband Narrowband
approx. 10 min. approx. 2 hrs approx. 3 hrs
approx. 20 min. approx. 4 hrs approx. 6 hrs
approx. 40 min. approx. 6 hrs approx . 9 hrs
approx. 60 min. approx. 8 hrs approx. 12 hrs
If the headset is outside the range of the base station, it will switch
off after 30 minutes in order to conserve battery power.
SD Pro2 – HSSD Office – HS SD Pro1 – HS
100 %75%25% 50%
Charging the headset
SD Series – Setup Guide | 13
Charging the headset using the optional CH 10
headset charger
The Sennheiser CH 10 headset charger is an optional accessory available
from yo
ur Sennheiser partner. The CH 10 allows you to charge additional
SD series headsets.
왘 Refer to the instruction manual of the C
H 10 for more information.
Charging several headsets simultaneously
The MCH 7 multi USB power source is an optional accessor
y available from
your Sennheiser partner. Together with the CH 10 USB, the MCH 7 allows
you to charge up to 7 headsets simultaneously.
왘 Refer to the instruction manual of the MCH 7
for more information.
SD Pro2 – HS
SD Office – HS
SD Pro1 – HS
MCH 7
CH 10 USB
Testing the headset system and the sound quality
14 | SD Series – Setup Guide
Testing the headset system and the
sound quality
Adjusting the headset system using the DIP switches
1 Press the Link button on the headset to disconnect an existing wireless
link between base station and headset.
The LEDs on the headset and on the base station go off.
2 Use a pointed object (e.g. a ball pen) to set the DIP switches to the
desir
ed position.
Co
nfiguring the handset lifter/hook switch
– DIP switches 1 and 2
The DIP switches 1 and 2 are only assigned a
function on the SD BS,
SD BS ML and SD BS Phone base stations.
1
2
1 2 3 4 5 6
DHSG
Handset Lifter
MSH
Short Range
Long Range
Auto Link ON
Auto Link OFF
Narrowband
Wideband
Limiter
Standard
Extra
Settings
Fast Link
Switch position Function
Manual operation
Lifts/hangs up the handset manually or using
the handset lifter (Sennheiser HSL 10 II).
Electronic hook switch (DHSG standard)
Call control via the headset system.
For faster link establishment, see Fast Link.
Electronic hook switch (MSH standard)
Call control via the headset system.
Fast Link for DHSG standard and HSL 10 II handset
lifter
Recommended for frequent callers. Shorter battery
life. Fast link establishment without delay due to
hidden link to the base station.
Testing the headset system and the sound quality
SD Series – Setup Guide | 15
Adjusting the radio range – DIP switch 3
If many DECT systems are operated in a confined space, interference can
occur. In this
case, you should change the radio range.
Automatically establishing the wireless l
ink between headset and
base station (Auto Link) – DIP switch 4
Switching between wideband and narrowband audio transmission –
DIP switch 5
Limiting the volume – DIP switch 6
Switch position Function
Standard radio range
Reduced radio range
Use this setting in order to avoid interference with
other DECT systems
Range of approx. 10 m indoors
SD Office – HS
SD Pro1 – HS
SD Pro2 – HS
Auto Link
Switch position Function
Manual link establishment
When taking the headset out of the base station,
you have to manually establish the wireless link
between headset and base station.
Automatic link establishment – Auto Link
When taking the headset out of the base station,
a wireless link is automatically established between
headset and base station.
Switch position Function
Wideband audio transmission
Automatic frequency adjustment of wideband and
narrowband calls. Wideband audio transmission
is e.g. supported by Skype and gives high speech
quality.
Battery life: 8 hours
Narrowband audio transmission
Battery life: 12 hours
Switch position Function
Standard limitation
Limited volume (country specific)
•AU version:
in compliance with Directive AS/ACIF G616:2006
• US version:
in compliance with Directive 2003/10/EC
Testing the headset system and the sound quality
16 | SD Series – Setup Guide
Adjusting the audio signal by means of the dial tone
1 Put on the headset and press the Phone button on the base station.
2 Press the Link button on the headset. The L
ink LED lights up blue.
3 Lift the handset. You hear a dial tone.
4 Set the ABC switch to the position A, B or C so that you can hear a clear
dial tone
in the headset.
1 2
3 4
Testing the headset system and the sound quality
SD Series – Setup Guide | 17
Adjusting the volume
Adjusting the microphone volume of the call transmission
By default, the microphone volume control is set to position 4. This setting
is suit
able for most telephones.
왘 Make a call to someone who will help you find the correct sensitivity
setting for your
microphone.
왘 Turn the microphone volume control so that the other party can hear
you at
a comfortable level.
Adjusting the microphone volume of the USB transmission
Some softphones adjust the microphone sensit
iv
ity automatically.
왘 Activate this function in order to be able to optimally use the micro-
phone and, via y
our operating system, adjust the microphone sensi-
tivity so that the other party can hear you at a comfortable level (see
the Help function of your operating system).
Adjusting the automatic audio transmission “Auto Audio”
With the “Auto Audio” function activated and in the case of a USB connec-
tion, the audio signals – e.g. from Windows
Media Player
or iTunes
–
are automatically transmitted to the headset.
When you receive a call or when a connection to Skype™ is established, the
audio transmission stops and you hear for example the ring tone. The
“Auto Audio” function is activated by default.
Activating the “Auto Audio” function
왘 Use a pointed object to press the Set button for approx. 5 seconds. The
Link LED
rapidly flashes blue several times.
Deactivating the “Auto Audio” function
왘 Use a pointed object to press the Set button for approx. 5 seconds. The
Link LED
rapidly flashes red several times.
5s
If a problem occurs
18 | SD Series – Setup Guide
If a problem occurs
For causes and solutions that are mainly related to the headset, refer to the chapter “If a problem occurs ...” in
the “User Guide”.
For more information and an FAQ list, please visit our website at www.sennheiser.com/cco.
If a problem occurs that is not listed in the above table or if the problem cannot be solved with the proposed
solutions, please contact your local Sennheiser partner for assistance.
To find a Sennheiser partner in your country, search at www.sennheiser.com/cco/support.
Problem Possible cause Possible solution Page
Headset is placed into the base
station but the Charge status
LED if off
Base station is not connected
to the mains power supply
Connect the base station to the
mains power supply.
7
Rechargeable battery is deep
discharged
Wait several minutes until the
Charge status LED lights up.
12
For quick-charging the headset:
Briefly press the Set button at the
bottom of the base station.
–
Link between headset and
base station cannot be
established
Base station is only connected
via the USB cable
Connect the base station to the
mains power supply.
7
Bad radio link between
headset and base station
Transmission range is
exceeded
Reduce the distance between
headset and base station.
–
Adjust the radio range. 15
Noise interference and
connection loss
Too many DECT systems within
the radio range
Reduce the radio range. 15
Set the base station to
narrowband transmission.
15
Distance between base station
and fixed line phone is so small
that interference occurs
Increase the distance between
base station and fixed line phone.
–
Rechargeable battery cannot
be charged
Headset is not properly placed
into the magnetic holder of the
base station
Check if the headset is properly
placed into the magnetic holder.
12
Bad audio quality, the other
party sounds too loud or too
low
Microphone sensitivity is not
correctly adjusted
Adjust the microphone sensitivity. 16
Sound from the fixed line
phone is distorted and
disturbed
Base station is not adjusted to
the fixed line phone.
Use the ABC switch to adjust the
base station to your fixed line
phone.
16
Specifications
SD Series – Setup Guide | 19
Specifications
Base station
SD BS/SD BS ML
SD BS USB/SD BS USB ML/SD BS Phone
Headset
SD Office – HS
SD Pro1/Pro2 – HS (SD 10)
Dimensions 83 x 127 x 121 mm (W x H x D)
Weight approx
. 337 g
Operating temperature range +5°C to +45°C (+41°F to +113°F)
Storage temperature range –20°C to +70°C (–4°F to +158°F)
Dimensions 83 x 127 x 121 mm (W x H x D)
Weight aprrox. 309 g
Operating temperature range +5°C to +45°C (+41°F to +113°F)
Storage temperature range –20°C to +70°C (–4°F to +158°F)
Dimensions 140 x 24 x 22 mm (W x H x D)
Weight with ear hook: approx. 22 g
with headband: approx. 50 g
Talk time narrowband: up to 12 hours
wideband: up to 8 hours
Charging time 50%: approx. 20 min
100%: approx. 1 hour
Range
(environment dependent)
free line of sight: up to 180 m
in office buildings: up to 55 m
Speaker type dynamic, neodymium magnet
Microphone type electret microphone, noise canceling
Operating temperature range +5°C to +45°C (+41°F to +113°F)
Storage temperature range –20°C to +70°C (–4°F to +158°F)
Dimensions 170 x 175 x 55 mm (W x H x D)
Weight Pro1: approx. 65 g
Pro2: approx. 85 g
Talk time narrowband: up to 12 hours
wideband: up to 8 hours
Charging time 50%: approx. 20 min
100%: approx. 1 hour
Range
(environment dependent)
free line of sight: up to 180 m
in office buildings: up to 55 m
Speaker type dynamic, neodymium magnet
Microphone type electret microphone, noise canceling
Operating temperature range +5°C to +45°C (+4°F to +113°F)
Storage temperature range –20°C to +70°C (–4°F to +158°F)
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Sennheiser SD Pro 1 Owner's manual
- Category
- Mobile headsets
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sennheiser DW Pro 1 USB Owner's manual
-
Sennheiser SD OFFICE User manual
-
-
Sennheiser DECT Comfort Calls DW Pro1/Pro2 User manual
-
Sennheiser D 10 Series Owner's manual
-
-
Sennheiser SDW 3 BS User manual
-
Sennheiser SDW 10 HS User manual
-
Sennheiser Electronic Corp 504302 User manual
-
Other documents
-
Avaya EU DoC for 1100 Series Deskphones User manual
-
Accutone WT88 Installation Manual & User Manual
-
Avaya 1400 Series Digital Deskphones Application Note
-
-
-
-
Dell 3.7.0 User manual
-
-
-
Momentum Sales & Marketing M2 OEBT User manual
