Promaster LED120PLUS Camera and Camcorder Light Owner's manual

Brand
Promaster
Model
LED120PLUS Camera and Camcorder Light
Type
Owner's manual

Promaster LED120PLUS Camera and Camcorder Light

The Promaster LED120PLUS Camera and Camcorder Light is a versatile and powerful lighting solution for photographers and videographers. With its 120 super bright LED lamps, it provides 51 Lux of luminance at 10 feet, ensuring ample illumination even in low-light conditions. The beam angle of 60° allows for wide coverage, while the color rendering index of ≥85 guarantees accurate color reproduction.

The LED120PLUS features a built-in high-capacity lithium polymer battery that provides up to 60 minutes of continuous runtime on a single charge. The remaining battery power can be easily checked using the power gauge LEDs. The light output can be adjusted in 4 steps to suit different lighting requirements.

Promaster LED120PLUS Camera and Camcorder Light

The Promaster LED120PLUS Camera and Camcorder Light is a versatile and powerful lighting solution for photographers and videographers. With its 120 super bright LED lamps, it provides 51 Lux of luminance at 10 feet, ensuring ample illumination even in low-light conditions. The beam angle of 60° allows for wide coverage, while the color rendering index of ≥85 guarantees accurate color reproduction.

The LED120PLUS features a built-in high-capacity lithium polymer battery that provides up to 60 minutes of continuous runtime on a single charge. The remaining battery power can be easily checked using the power gauge LEDs. The light output can be adjusted in 4 steps to suit different lighting requirements.

Rechargeable LED Light Panel
LED120
Plus
Thank you for purchasing the PROMASTER
®
LED120PLUS Light Panel.
Please read the following instructions to ensure the best
operation of your light panel.
AC Power Supply/Charger
1) Power input port
2) Charge indicator light
3) Internal battery check button
4) Remaining power gauge
5) Light output adjustment buttons
6) On/Off power switch
Charging the Internal Battery
The PROMASTER
®
LED120PLUS has a built-in high capacity lithium polymer battery. Be sure to charge this battery fully before the
initial use of the light. To charge, insert the plug of the AC power supply into the power input port (1). Plug the AC power supply into a
standard electrical outlet. The charge indicator light (2) will glow red. When the battery is fully charged, the charge indicator light (2)
will glow green. Your LED120PLUS should provide about 60 minutes of continuous run time on a new fully charged battery.
Checking the Remaining Battery Power
To check the power remaining in the internal battery, press the internal battery check button (3). The remaining power gauge LEDs
will light. If all four LEDs light, the battery is full, 3 LEDs indicate 75%, 2 LEDs indicate 50%, 1 LED indicates 25% or less and you
unit should be charged at the first opportunity.
1
2
3
4
5
6
Power ON/OFF
To power the unit on or off, move the power switch (6) to the appropriate position.
Adjusting the Light Output
The light output of your LED120PLUS can be adjusted by 4 steps. To make the light brighter, press the up arrow × of the light output
adjustment buttons (5) until the light reaches maximum brightness. To reduce the light output, press the down arrow Ø of the light
output adjustment buttons (5).
Installing or Removing the Color Correction Filter
Your LED120 light is supplied with a 3300K correction filter that helps give you the best color balance when shooting under ambient
tungsten lighting. This filter is easily installed by snapping over the edge of your LED120 light. To remove simply lift the filter off.
3300K Filter LED120 with
filter installed
Using the Camera Bracket
B A
Attach the mounting screw (A) to the tripod mount of your camcorder/camera. Slide your light into the shoe (B) of the mounting
bracket.
Specifications
Light source: 120-5mm super bright LED lamps
Beam angle: 60°
Luminance: 51 Lux @ 10’
Color rendering index: ≥85
Color temperature: 5600K
LED longevity: >10000h
Power input: Internal Lithium Polymer Rechargeable Battery 3.7V / 3AH
Housing size(mm): 94 x 93 x 38
Weight(g): 155
Code 7207
Made in China
www.promaster.com
Fairfield, CT 06611
  • Page 1 1
  • Page 2 2

Promaster LED120PLUS Camera and Camcorder Light Owner's manual

Brand
Promaster
Model
LED120PLUS Camera and Camcorder Light
Type
Owner's manual

Promaster LED120PLUS Camera and Camcorder Light

The Promaster LED120PLUS Camera and Camcorder Light is a versatile and powerful lighting solution for photographers and videographers. With its 120 super bright LED lamps, it provides 51 Lux of luminance at 10 feet, ensuring ample illumination even in low-light conditions. The beam angle of 60° allows for wide coverage, while the color rendering index of ≥85 guarantees accurate color reproduction.

The LED120PLUS features a built-in high-capacity lithium polymer battery that provides up to 60 minutes of continuous runtime on a single charge. The remaining battery power can be easily checked using the power gauge LEDs. The light output can be adjusted in 4 steps to suit different lighting requirements.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents