American Dynamics 1335 series Installation guide

Type
Installation guide

This manual is also suitable for

American Dynamics 1335 series is a weatherproof/dustproof housing designed for both indoor and outdoor use. It is constructed of aluminum and has a light beige powder coat enamel finish. The housing has three weatherproof cable entries and a 3.5"W x 2.75"H (89 x 70 mm) window made of 1/4" plate glass. The housing can accommodate a variety of cameras and lenses, and it comes with a built-in heater to prevent the camera from freezing in cold weather. The heater is a PTC type with automatic regulation, and it consumes 1.0 A (maximum) of power.

American Dynamics 1335 series is a weatherproof/dustproof housing designed for both indoor and outdoor use. It is constructed of aluminum and has a light beige powder coat enamel finish. The housing has three weatherproof cable entries and a 3.5"W x 2.75"H (89 x 70 mm) window made of 1/4" plate glass. The housing can accommodate a variety of cameras and lenses, and it comes with a built-in heater to prevent the camera from freezing in cold weather. The heater is a PTC type with automatic regulation, and it consumes 1.0 A (maximum) of power.

INSTALLATION:
To Open Housing:
To open the housing, release the four tamper-resistance
screws located at the rear of the housing. (using supplied
4 mm allen wrench).
Slide the outer housing forward until it reaches the fold-
down position (If you want to remove the outer housing
from the mount, rotate the outer housing 90 degrees to the
side).
To Mount the Housing:
The 1335/1337 mounting hardware is shipped inside the
housing. To open the housing, see above.
To mount the housing, slide the head of the two 6 mm bolts
(supplied) into the slide rail located on the bottom of the
housing.
Position the holes in the slide rail to line-up holes in the
mounting surface.
Secure housing with supplied washers and 6 mm nuts.
Camera Installation:
Mount lens to camera body.
Remove adjustable camera slide from housing (2 mm allen
wrench).
Mount the camera assembly to the slide using 1/4"-20 bolt
and tighten.
Install the camera into the housing selecting the proper
slide height in order to center the lens in housing window.
Tighten the camera slide (2 mm allen wrench) to prevent
movement of the camera during operation.
Wiring Installation:
Route cables through rear of housing using the two com-
pressing cable entries.
Tighten compression fittings to insure proper weatherproof
condition.
HEATER ASSEMBLY:
Mounting Instructions:
Wire thermostat to terminal block after removing jumper.
Mount the heater element into the front channel on the
housing.
Plug the heater assembly into the terminal block.
Mount the terminal block to the rear of the housing (use the
screws supplied).
The terminal block is designed to distribute main power to
camera and heater. CAUTION: Make sure supply voltage
and equipment voltages are compatible.
SUPPLY VOLTAGE:
20 VA- Heater Assembly
15 VA- Camera Assembly
* * * * * * * *
Thermostat
Camera
Main
Ground
Mounting Holes
Heater
HEATER
Specifications
Mechanical Characteristics
Operating Environment: Indoor/Outdoor
Construction: Aluminum
Finish: 1315 - Light beige powder coat enamel
1317 - Natural aluminum finish
Model Standard w/ sunshield
Weight: 1335/14 7.55 lb (3.4 Kg) 10.5 lb (4.87 Kg)
1337/14
1335/18 _____ 12.0 lb (5.4 Kg)
1337/18
Cable Entry: Three, weatherproof glands
Window: Size - 3.5"W x 2.75"H (89 x 70 mm) Construction: 1/4" plate glass
Camera: Mounting - Non metallic mounting plate with four levels of height and full front to back adjustment
Heater: Type: PTC, automatic regulation
Voltage: 24VAC/VDC (12-30V)
Power Consumption: 1.0 A (maximum)
Weight: 0.15 lb (0.68 kg)
Environmental Characteristics
Weatherproof Standard: NEMA 4 (IP 65)
Other Models:
Deluxe:
1335/14 Weatherproof/dustproof housing with light beige powder coat enamel finish.
Supplied in 14 inch lengths.
1335/14S Same as above with sunshield
1335/14SH24 Same as above with sunshield and 24 volt heater installed
1335/18SH24 (120 V heaters can be substituted for 24V heater by specifying 120 in the housing model
number, i.e., 1335/14SH120.)
General Purpose:
1337/14 Weatherproof/dustproof housing with
natural aluminum finish. Supplied in
14 inch lengths
1337/14S Same as above with sunshield
1337/14SH24 Same as above with sunshield and 24 volt heater installed
1337/18SH24 (120 V heaters can be substituted for 24V heater by specifying 120 in the housing model
number, i.e., 1337/14SH120.)
An American Dynamics Product
Designed and built by
Sensormatic CCTV Systems Division
One Blue Hill Plaza
Pearl River, New York, 10965
(914) 624-7600
Technical Support Center: 1-800-442-2225
FAX: 914-624-7685
OP1335/ 1337A August 1993
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Dynamics 1335 series Installation guide

Type
Installation guide
This manual is also suitable for

American Dynamics 1335 series is a weatherproof/dustproof housing designed for both indoor and outdoor use. It is constructed of aluminum and has a light beige powder coat enamel finish. The housing has three weatherproof cable entries and a 3.5"W x 2.75"H (89 x 70 mm) window made of 1/4" plate glass. The housing can accommodate a variety of cameras and lenses, and it comes with a built-in heater to prevent the camera from freezing in cold weather. The heater is a PTC type with automatic regulation, and it consumes 1.0 A (maximum) of power.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI