Messoa SLI080 Mounting Guide

IR Illuminator Brackets

Mounting Installation Guide

P32-081020-000A A1

Mounting Installation Guide



Table of Contents

1. Introduction.............................................................................................3

2. Standard Wall Mount..............................................................................3

3. Single L-Type Wall Mount......................................................................4

4. Dual L-Type Wall Mount.........................................................................7

5. Pole Mount.............................................................................................10

6. Corner Mount ........................................................................................13



2

Mounting Installation Guide



1. Introduction

This mounting installation guide is intended to provide installers with basic

instructions of how to mount the High Power Intelligent IR Illuminator (hereafter

referred to as the illuminator) using optional accessories from MESSOA. If you are

using other specialized mounting accessories or tools, always refer to the instruction

document supplied with that product.

Note: Always use the screws as instructed by this guide to ensure proper

installation.

This guide will describe the following mounting methods:

 Standard Wall Mount

 Single / Dual L-Type Wall Mount

 Pole Mount

 Corner Mount

Before Installation

Before mounting the camera onto the bracket, please first secure the mount bracket

of your choice firmly at the desired position to a solid surface using appropriate

screws and plugs. Also make sure to route all the required cables properly.

2. Standard Wall Mount

This mounting method requires no additional

accessory. Use the guide pattern provided with

the illuminator to drill holes on desired surface.

Then mount the bracket of the illuminator using

appropriate anchors and screws (not provided).

.

3

Mounting Installation Guide



3. Single L-Type Wall Mount

Before beginning the following procedure, please make sure to have these items

ready:

L-Type Single Wall Mount Bracket

Screw Set x 3 Guide Pattern

1. Use the guide pattern to drill holes on desired location. Then attach the bracket

using appropriate anchors and screws (not provided).

2. Take the provided screw sets, remove

the nut and the washer as shown in

the figure.

3. Using provided screw sets, attach the illuminator above or below the bracket and

adjust the angle as needed. When desired angle is achieved, fasten the washers

and nuts onto the screw sets.

4

Mounting Installation Guide



4. The illustration below shows the examples of illuminator adjusted to desired

angle.

Note: When the illuminator is adjusted to a certain angel, only 2 screw sets will

be needed to fasten the illuminator.

5

Mounting Installation Guide



Single L-Type Wall Mount Dimensions

160mm (6.30”)

110mm (4.33”)

206mm (8.11”)

Ø

9

m

(

0

.

3

5

”

)

Ø

9

m

(

0

.

3

5

”

)

92mm (3.62”)

Ø111mm (4.37”)

Ø20mm (0.79”)

6

Mounting Installation Guide



4. Dual L-Type Wall Mount

Before beginning the following procedure, please make sure to have these items

ready:

L-Type Dual Wall Mount

Bracket

Screw set x 4

Guide Pattern

1. Use the guide pattern to drill holes on desired location. Then attach the bracket

using appropriate anchors and screws (not provided).

2. Take the provided screw sets

and remove the nut and the

washer.

3. Using provided screw sets,

attach the illuminators above or

below the bracket and adjust the

angle as needed. When desired

angle is achieved, fasten the

washers and nuts onto the screw

sets.



7

Mounting Installation Guide



4. The illustration below shows the examples of finished installations.

8

Mounting Installation Guide



Dual L-Type Wall Mount Dimensions

228mm(8.98")

Ø

3

8

m

(

1

.

5

"

)

Ø

9

m

(

0

.

3

5

"

)

*

4

204mm(8.03")

350mm(13.78")

70mm(2.76")

50mm(1.97")

260mm(10.24")

165mm(6.5")

110mm(4.33")

Ø

9

m

(

0

.

3

5

"

)

*

2

Ø

9

m

(

0

.

3

5

"

)

*

2

160

o

270

o

9

Mounting Installation Guide



5. Pole Mount

Before beginning the installation, please make sure to have these items ready:

Pole Mount Bracket Screw set x 4 Metal strap x 2

Optional brackets for use with the pole mount bracket:

Single Wall Mount Bracket

(with screw set x 3)

Dual Wall Mount Bracket

(with screw set x 4)

1. Thread the metal strap through

the holes on the bracket and then

tighten screws on the strap.

3. Take the provided screw sets,

remove the nut and the washer.

10

Mounting Installation Guide



4. Option 1: Mount the illuminator

directly to the bracket using the

screw sets.

4. Option 2: Attach the single wall mount bracket to the pole mount bracket using

the screw sets.

Then mount the illuminator to the bracket using the screw sets.

5. Option 3: Attach the dual wall mount bracket to the pole mount bracket using

the screw sets.

Then mount the illuminators to the bracket using the screw sets.

11

Mounting Installation Guide



Pole Mount Bracket Dimension

20mm(0.79")

36.9°

3.2mm(0.12")

59.76mm(2.35")

6mm(0.24")

165mm(6.49")

260mm(10.23")

238.4mm(9.38")

Ø40mm(1.57”)

101.6mm(4.0")

3.5mm(0.14")

72mm(2.83")

94mm(3.7")

110mm(4.33")

20mm(0.79")

Ø9mm(0.35)x10

12

Mounting Installation Guide



6. Corner Mount

Before beginning the following procedure, please make sure to have these items

ready:

Corner Mount Bracket Screw set x 4

Optional brackets for use with the pole mount bracket:

Single Wall Mount Bracket

(with screw set x 3)

Dual Wall Mount Bracket

(with screw set x 4)

1. Attach the bracket using

appropriate anchors and screws

(not provided).

2. Take the provided screw sets,

remove the nut and the washer.

13

Mounting Installation Guide



3. Option 1: Mount the illuminator

directly to the bracket using the

screw sets.

4. Option 2: Attach the single wall mount bracket to the pole mount bracket using

the screw sets.

Then mount the illuminator to the bracket using the screw sets.

5. Option 3: Attach the dual wall mount bracket to the pole mount bracket using

the screw sets.

Then mount the illuminator to the bracket using the screw sets.

14

Mounting Installation Guide



15

Corner Mount Bracket Dimensions

Messoa SLI080 Mounting Guide

Messoa SLI080 Mounting Guide

Other documents