FLIR N133-233 Domes User guide
- Category
- Security cameras
- Type
- User guide
PACKAGE CONTENTS:
1 x CD
1 x IP Dome Camera
Quick Start Guides
Installing the Camera
A
3MP HD IP Dome Camera
N233EE
Quick Connection Guide
B
• Use an appropriate low voltage power cable to prevent fire or electrical
shock.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please use
a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for submersion
in water.
Safety Precautions
Weights & Dimensions
3.7” / 93mm
C
Installing the Camera (continued)
Connecting the Camera
0.6lbs / 0.3kg
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Notice
1
2
3
1 x Allen Key
1. Ethernet Port: Connect the camera to an NVR or a router or
switch on your network using Cat5e or better Ethernet cable
(not included). PoE Class 3 supported.
2. Power Input: If not using PoE, connect the camera to a 12V
DC power source (300mA or higher required).
G
H
Remove the vinyl film from the camera lens once
installation is complete.
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2014 FLIR Systems, Inc. All rights reserved.
www.flirsecurity.com/pro
For support, visit
Latest software and manuals available on
www.flirsecurity.com/pro
N233EE_QCG_EN_R1
I
Weight
3.2” /
81mm
Move the ball camera to the desired position. While
holding the ball camera firmly in place, twist the dome
cover the rest of the way to secure it to the camera base.
Holding the camera prevents it from moving while securing
the adjustment ring.
D
When finished, use the included Allen key to tighten the
screws on the dome cover.
4 x Mounting Screws
Use the included Allen key to loosen the screws on the
dome cover.
Rotate the camera base counter-clockwise to separate it
from the ball camera, adjustment ring, and dome cover.
NOTE: Use the included drywall anchors if installing on a
drywall surface.
Feed the camera cables through the camera base.
Connect the video and power cable as shown in the
section ‘Connecting the Camera’.
1
2
4 x Drywall Anchors
E
Mount the camera base to the mouting surface using the
included mounting screws.
Camera base
Dome cover
Ball camera
Adjustment ring
F
Place the
adjustment ring
over the dome cover,
then place both over
the ball camera. Twist
the adjustment ring
clockwise to secure the
components in place.
Do not tighten all
the way.
Drywall anchors
Mounting
screws
-
1
FLIR N133-233 Domes User guide
- Category
- Security cameras
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
FLIR N133-233 Bullet Camera User guide
-
-
-
-
FLIR PB133F User guide
-
-
-
FLIR N253EA8/N253EA8BK User guide
-
-
Other documents
-
Digimerge DNE12TL2 User guide
-
-
-
-
-
-
-
Lorex 2KHDIP844D Quick start guide
-
Lorex LN10802-166W Quick start guide
-
Digimerge DNV16M2 User guide