Clinton Electronics CE-VXRM User manual

Clinton Electronics
Brand
Clinton Electronics
Model
CE-VXRM
Category
Security camera accessories
Type
User manual

Clinton Electronics CE-VXRM is a vandal-resistant dome camera designed for both indoor and outdoor use. It features a 5-1/2" hole saw for easy installation and a 1-1/4" maximum mounting material depth. The camera has four position adjustments: barrel rotation, lens angle, lateral adjustment, and camera plate rotation. It also includes a CE-REMOTE for OSD adjustment and test monitor connection. The CE-VXRM is weather-resistant with an IP68 rating, making it suitable for use in harsh conditions.

Clinton Electronics CE-VXRM is a vandal-resistant dome camera designed for both indoor and outdoor use. It features a 5-1/2" hole saw for easy installation and a 1-1/4" maximum mounting material depth. The camera has four position adjustments: barrel rotation, lens angle, lateral adjustment, and camera plate rotation. It also includes a CE-REMOTE for OSD adjustment and test monitor connection. The CE-VXRM is weather-resistant with an IP68 rating, making it suitable for use in harsh conditions.

v.05.24.11
CLINTON Electronics
6701 Clinton Road
Loves Park, IL 61111
1.800.447.3306 Sales
1.800.549.6393 Support
1.800.633.8712 Fax
www.clintonelectronics.com
Installing the Vandal X Dome Camera using the Recess Mount:
3. Opening the Case
Use the supplied Torx wrench to remove the 3 Torx screws that hold the
dome assembly onto the base
Locate and remove the 4 Phillips head screws that hold the inner case
onto the camera base. Note: Arrowheads indicate screw location.
Remove the camera assembly from the camera base as shown below.
Set this base aside. You will not need this base when using the Recess Mount.
CE-VXRM / VXRMB
INSTALLATION GUIDE
Fold the wings inward to slide the Recess Mount into the 5-1/2” hole.
With a Phillips head screwdriver, rotate the three screws clockwise to ip the tension
wings out until they rmly grip the mounting material. NOTE: When mounting, make
sure the mounting surface does not block the three perimeter holes shown below.
These holes must be clear in order to accept the VX case in the next steps.
1. Preparing Mounting Surface
The VXRM requires a minimum of 3” depth and can be installed on mounting
surfaces up to 1-1/4“ thick. Cut a hole in your mounting surface using a 5-1/2”
hole saw.
5-1/2” Hole
3” Min Depth
1-1/4” Max Mounting
Material Depth
2. Installing the Recess Mount
Align the tab with the slot when reassembling.
Replace the four screws that hold the camera assembly to the base.
Note: Arrowheads indicate screw location.
Arrowhead indicates
screw location.
Adjustment:
The Vandal X Dome Camera has four position adjustments:
A. Barrel rotation
B. Lens angle
C. Lateral adjustment (loosen thumb screws on each side to adjust)
D. Camera plate rotation (pinch the camera bracket by each thumb screw to
rotate clockwise or counterclockwise)
Testing:
Before replacing the dome cover you may wish to test the camera with a test
monitor. To test, plug in the CE-REMOTE into the DIN connection shown below
and connect your test monitor to the BNC connection located on the CE-REMOTE
cable. Refer to camera manual for detailed OSD adjustment settings.
for OSD Adjustment & Test Monitor Connection compatibility.
Tighten the 3 Torx screws that hold the dome cover onto the base to complete
installation. Make sure that each screw is tight to ensure superior weather resistance.
UP
DOWN
RIGHT
LEFT
A
B
C
D
3. Mounting the Camera
Feed the power and video cables through the
hole marked
“CABLES GO HERE”.
NOTE: Due to the replacement of the bottom case, a 1/16” gap between the
VXRM and the VX camera dome will result. This will not aect the IP68 weather
rating of the VX series camera.
  • Page 1 1
  • Page 2 2

Clinton Electronics CE-VXRM User manual

Clinton Electronics
Brand
Clinton Electronics
Model
CE-VXRM
Category
Security camera accessories
Type
User manual

Clinton Electronics CE-VXRM is a vandal-resistant dome camera designed for both indoor and outdoor use. It features a 5-1/2" hole saw for easy installation and a 1-1/4" maximum mounting material depth. The camera has four position adjustments: barrel rotation, lens angle, lateral adjustment, and camera plate rotation. It also includes a CE-REMOTE for OSD adjustment and test monitor connection. The CE-VXRM is weather-resistant with an IP68 rating, making it suitable for use in harsh conditions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents