Linksys BEFSR41W Owner's manual

Category
WLAN access points
Type
Owner's manual
Instant Broadband™ Series
EtherFast
®
Cable/DSL
Wireless-Ready Router
with 4-Port Switch
Use this Guide to install:
BEFSR41W EtherFast Cable/DSL Wireless-Ready Router with 4-Port Switch
User Guide
Downloaded from www.Manualslib.com manuals search engine
COPYRIGHT & TRADEMARKS
Copyright © 2002 Linksys, All Rights Reserved. Instant Broadband is a registered trade-
mark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks
of Microsoft Corporation. All other trademarks and brand names are the property of their
respective proprietors.
LIMITED WARRANTY
Linksys guarantees that every Instant Broadband EtherFast
®
Cable/DSL Wireless-Ready
Router with 4-Port Switch will be free from physical defects in material and workmanship
for one year from the date of purchase, when used within the limits set forth in the
Specifications chapter of this User Guide. If the product proves defective during this war-
ranty period, call Linksys Technical Support in order to obtain a Return Authorization
Number. BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM
THE PRODUCT'S PACKAGING ON HAND WHEN CALLING. RETURN REQUESTS CAN-
NOT BE PROCESSED WITHOUT PROOF OF PURCHASE. When returning a product,
mark the Return Authorization Number clearly on the outside of the package and include
a copy of your original proof of purchase. All customers located outside of the United
States of America and Canada shall be held responsible for shipping and handling
charges.
IN NO EVENT SHALL LINKSYS’ LIABILITY EXCEED THE PRICE PAID FOR THE PROD-
UCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAM-
AGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFT-
WARE, OR ITS DOCUMENTATION. LINKSYS OFFERS NO REFUNDS FOR ITS PROD-
UCTS. Linksys makes no warranty or representation, expressed, implied, or statutory,
with respect to its products or the contents or use of this documentation and all accom-
panying software, and specifically disclaims its quality, performance, merchantability, or
fitness for any particular purpose. Linksys reserves the right to revise or update its prod-
ucts, software, or documentation without obligation to notify any individual or entity.
Please direct all inquiries to:
Linksys P.O. Box 18558, Irvine, CA 92623.
FCC STATEMENT
The Instant Broadband EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used according to the
instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which is found by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment or devices
• Connect the equipment to an outlet other than the receiver’s
• Consult a dealer or an experienced radio/TV technician for assistance
UG-BEFSR41W-051402B BW
Downloaded from www.Manualslib.com manuals search engine
Log 30
Help 31
UPnP 32
Filters 33
Port Forwarding 35
Dynamic Routing 39
Static Routing 40
DMZ Host 41
MAC Address Cloning 43
Appendix A: Troubleshooting 44
Common Problems and Solutions 45
Frequently Asked Questions 46
Appendix B: How to Obtain Your ISP’s E-mail
& Web Addresses 50
Appendix C: Installing the TCP/IP Protocol 53
Appendix D: Twisted-Pair Cabling 55
Crimping Your Own Network Cables 56
Appendix E: Glossary 57
Appendix F: Specifications 63
Environmental 64
Appendix G: Warranty Information 65
Appendix H: Contact Information 66
Table of Contents
Chapter 1: Introduction 1
Linksys Cable/DSL Wireless-Ready Router 1
Features 1
Package Contents 2
Minimum Requirements 2
Chapter 2: Getting to Know the Cable/DSL
Wireless-Ready Router 3
The Cable/DSL Wireless-Ready Router’s Rear Panel 3
The Wireless PC Card (not included) 4
The Reset Button 4
The Cable/DSL Wireless-Ready Router’s Front Panel LEDs 5
Chapter 3: Connecting the Cable/DSL
Wireless-Ready Router to Your Network 7
Overview 7
About Static & Dynamic IP Addresses 7
Connecting Your Hardware Together & Booting Up 8
Configuring Your PCs to Connect to the
Cable/DSL Wireless-Ready Router 10
Chapter 4: Adding Wireless Capabilities to
Your Router 12
Chapter 5: Configuring Your Network with the
Cable/DSL Wireless-Ready Router 16
Configuring the Cable/DSL Wireless-Ready Router 16
Chapter 6: The Cable/DSL Wireless-Ready
Router’s Web-based Utility 20
Quick and Easy Administration 20
Setup 21
Setting WEP Encryption 24
Password 26
Status 27
DHCP 29
Instant Broadband
TM
Series
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
Downloaded from www.Manualslib.com manuals search engine
Chapter 1: Introduction
The Linksys Cable/DSL Wireless-Ready Router
Congratulations on your purchase of an EtherFast
®
Cable/DSL Wireless-Ready
Router with 4-Port Switch. The EtherFast
®
Cable/DSL Wireless-Ready Router with
4-Port Switch provides the ideal solution for connecting your network to a high-
speed broadband Internet connection and a 10/100 Fast Ethernet backbone, with the
option to add wireless capabilities. Configurable as a DHCP server for your exist-
ing network, the Router acts as the only externally recognized Internet gateway on
your local area network (LAN) and serves as an Internet NAT firewall against
unwanted outside intruders. Plus, the Router functions as an Access Point when you
add a Wireless Network PC card (not included) to enable wireless connectivity.
A typical router relies on a separate hub or a switch to share its Internet connection,
but the Linksys EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
channels this connection through the blazing, full duplex speed of its built-in
EtherFast
®
10/100 4-Port Switch. This cutting-edge combination of wireless-ready
router and switch technology eliminates the need to buy an additional hub or
switch—just add a Wireless Network PC card to connect the router to your wireless
network. Now your entire wireless network can enjoy blazing broadband Internet
connections supported by its robust switched backbone. With the dual-function
speed and power of the EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port
Switch, your network will take off at speeds faster than you ever imagined possible.
Expandable to Support Wireless Networking
Compatible with Universal Plug and Play (UPnP)
MAC Address Filtering
Configurable through Your Networked PC’s Web Browser
Supports IPSec and PPTP Pass-Through
Internal 4-Port Switch Dramatically Speeds Up Your Gaming
Able to Act as a DHCP Server for Your Existing Network
Wireless Capabilities Available with Use of Optional WPC11 (sold separately)
Connects to a Broadband Modem, a 10/100 Ethernet Backbone, or a
Wireless Network
Interoperable with IEEE 802.11b (DSSS) 2.4GHz-Compliant Equipment
Provides Roaming, Best Access Point Selection, Load Balancing, and
Network Traffic Filtering
Long Operating Range Supports up to 91m (Indoors) and up to 457m
(Outdoors)
Capable of up to 128-Bit WEP Encryption
Free Technical Support—24 Hours a Day, 7 Days a Week, Toll-Free US Calls
1-Year Limited Warranty
Features
1
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
Downloaded from www.Manualslib.com manuals search engine
Chapter 2: Getting to Know the
Cable/DSL Wireless-Ready Router
The Cable/DSL Wireless-Ready Router’s Rear Panel
The back panel of the Router is where all of the Router’s connections are made.
WA N The WAN (Wide Area Network) Port is where you
will connect your cable or DSL modem.
Ports 1-4 These four LAN (Local Area Network) ports are
where you will connect networked devices, such as
PCs, print servers, and any other Ethernet devices
you want to put on your network. These ports will
auto-detect the use of crossover or straight RJ-45
cables.
Power The Power Port is where you will connect the
included AC Power adapter.
PCMCIA Slot This is where you can connect the optional wireless
PC card (not included) for wireless features.
3
Figure 2-1
2
Package Contents
• One Linksys EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port
Switch (1)
• One Power Adapter (2)
• One TechHelper CD-ROM (3)
• One User Guide (4)
• Quick Installation (not shown)
• One Registration Card (not shown)
Minimum Requirements
• Network Adapter with Ethernet (UTP CAT 5) Cabling and TCP/IP Protocol
Installed per PC
• Internet Explorer 4.0 or Netscape Navigator 4.7 or Higher for Web-Based
Configuration
• Cable or DSL Modem with Ethernet Connection and Internet Access
• CD-ROM Drive
• WPC11 for Wireless Connection (sold separately)
Figure 1-1
Instant Broadband
TM
Series
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
Downloaded from www.Manualslib.com manuals search engine
The Cable/DSL Wireless-Ready Router’s Front Panel LEDs
Diag Red. The Diag LED illuminates when the Router goes
through its self-diagnosis mode during boot-up and restart. It
will turn off upon successful completion of the diagnosis. If
this LED stays on for an abnormally long period of time,
refer to the Troubleshooting section. During firmware
upgrades, this will also flash.
Power Green. The Power LED illuminates when the Router is pow-
ered on.
Full/Col Green. The Full/Col LED also serves two purposes. If this
LED is continuously illuminated, the connection made
through the corresponding port is successfully running in
Full Duplex mode. If the LED is flickering, the connection is
experiencing collisions. Infrequent collisions are normal. If
this LED is flickering too often, there may be a problem with
your connection. Check the Troubleshooting section if you
think there is a problem.
Link/Act Green. The Link/Act LED serves two purposes. If the LED
is continuously illuminated, the Router is successfully con-
nected to a device through the corresponding port (1, 2, 3 or
4). If the LED is flickering, the Router is actively sending or
receiving data over that port.
100 Orange. The 100 LED illuminates when a successful
100Mbps connection is made through the corresponding
port.
4
Figure 2-3
The Wireless PC Card (not included)
To add wireless capabilities, a WPC11 (sold separately) is required.
Power off the Router. Insert the WPC11 in the manner shown above
in the warning label. Push the WPC11 into the BEFSR41W until it
is securely held in place by the PCMCIA Slot.
5
The Reset Button
To use the Reset button:
Unplug the power adapter from the Router. Then, plug the power
adapter back into the Router. Press the Reset button. The Diag LED will flash
after three seconds.
To restore the factory default settings, Unplug the power adapter from the
Router. Press the Reset button and hold for three seconds while plugging the
power adapter back into the Router.
Figure 2-2
Instant Broadband
TM
Series
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
The Wireless-PC Card
The Reset Button
Downloaded from www.Manualslib.com manuals search engine
Chapter 3: Connecting the
Cable/DSL Wireless-Ready
Router to Your Network
Overview
Unlike a simple hub or switch, the setup of the Cable/DSL Wireless-Ready
Router consists of more than simply plugging everything together. Because the
Router acts as a DHCP server, you will have to set some values within the
Router, and also configure your networked PCs to accept the IP Addresses the
Router chooses to assign them.
You will need the following values from your ISP in order to install the
Cable/DSL Wireless-Ready Router:
• PPPoE with username and password (for some DSL users)
Your broadband-configured PC’s static Internet IP Address (if applicable)
Your broadband-configured PC’s Computer Name and Workgroup Name
Your Subnet Mask
Your Default Gateway
Your Primary DNS IP address
If your broadband access installer did not leave you this information, call your
ISP and they will be able to supply you with it.
About Static & Dynamic IP Addresses
Static IP Addresses A static IP address is an IP address permanently assigned
to a computer in a TCP/IP network. Static IP addresses are usually assigned to
networked devices that are consistently accessed by multiple users, such as
server PCs, or a print server. If you are using your Router to share your cable
or DSL Internet connection, contact your ISP to see if they have assigned your
home a static IP address. You will need that address during your Router’s con-
figuration.
About Static & Dynamic IP Addresses
7
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
6
WLAN Green. The WLAN LED illuminates when a wireless net-
work is active.
WA N Green. The WAN LED illuminates when a successful con-
nection is made between the Router and your Broadband
device or network. When blinking, the Router is sending or
receiving data over the broadband port.
Instant Broadband
TM
Series
Downloaded from www.Manualslib.com manuals search engine
6. To use the Reset button: While holding down the Reset button, unplug the
power adapter from the Router. Wait three seconds while continuing to hold
down the Reset button. Then plug the power adapter back into the Router.
The Diag LED will flash twice. During the second flash, release the Reset
button. This will restore all the defaults.
7. Power on your PC.
The Hardware Installation is complete. Continue to the next page to con-
figure your PCs and Router.
NNoottee::
Some ISPs—most notably some cable providers—configure
their networks so that you do not have to enter a full Internet
address into your web browser or e-mail application to reach your
home page or receive your e-mail. If your Internet home page
address is something very simple, such as “www”, rather than
“www.linksys.com”, or your e-mail server’s address is something similar to “e-
mail” or “pop3”, rather than “pop.mail.linksys.com”, you won’t be able to prop-
erly configure your Router until you determine the actual Internet addresses of
your Web and e-mail connections.
You
mmuusstt
obtain this information prior to connecting the Router to your network.
You can obtain this information by contacting your ISP, or you can turn to the
section of the Appendix on
HHooww ttoo OObbttaaiinn YYoouurr IISSPPss EE-mmaaiill && WWeebb AAddddrreesssseess..
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
9
Dynamic IP Addresses A dynamic IP address is an IP address that is automati-
cally assigned to a client station (computer, printer, etc.) in a TCP/IP network.
Dynamic IP addresses are typically assigned by a DHCP server, which can be
a computer on the network or another piece of hardware, such as the Router. A
dynamic IP address might change every time your computer connects to the
network.
DHCP (Dynamic Host Configuration Protocol) DHCP is software that automati-
cally assigns IP addresses to client stations logging on to a TCP/IP network.
DHCP eliminates having to manually assign permanent IP addresses to every
device on your network. DHCP software typically runs in servers and is also
found in network devices such as Routers.
Connecting Your Hardware Together and Booting Up
Once you are sure that you have the above values on hand, you can begin the
installation and setup of your Cable/DSL Wireless-Ready Router.
1. Power everything down, including your PCs, your Cable or DSL modem and
the Router.
2. Connect a Network cable from one of your PCs’ Ethernet ports to one of the
LAN Ports on the back of the Router. Do the same with all the PCs you wish
to connect to the Router.
3. Connect the network cable from your Cable or DSL modem to the WAN port
on the back of the Router.
4. Connect the power-adapter cable to the Power port on the back of the Router,
then plug the other end into a power outlet.
The Power LED will illuminate green as soon as the power adapter is
connected.
The Diag LED will illuminate red for a few seconds while the Router
goes through its internal diagnostic test. The LED will turn off when the
self-test is complete.
5. Power on the Cable or DSL modem. Verify that the power is on by checking
the WAN LED on the front of the Router. The Link LED will illuminate if
the power is on and the modem is ready.
Instant Broadband
TM
Series
8
Downloaded from www.Manualslib.com manuals search engine
4. Click the Properties button, and then choose the IP Address tab. Select
Obtain an IP address automatically. (See Figure 3-2.) Click on the
Gateway tab and make sure that all fields there are empty. Click OK.
5. The Network Properties window will reappear. Click OK. All client settings
are complete. Windows may ask for original Windows installation files,
which can be found on your Windows CD-ROM (i.e.: D:\win98, D:\win95,
D:\ win9x - where “D” is the letter of your CD-ROM drive) or possibly on
your hard drive (c:\windows\options\cabs.)
6. Windows will ask you to restart your PC. Click Yes.
Repeat steps 1-6 for each PC on your network.When all PCs are config-
ured, continue on to set up the Router using the Router’s Web-based
Utility.
Figure 3-2
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
11
Now that your Router is physically installed, you will have to configure your
PCs to accept the IP addresses that your Router will provide. If using the
default Windows TCP/IP network configuration, no changes are required; just
restart your PC so it will obtain an IP address from the Cable/DSL Wireless-
Ready Router.
1. Click the Start button, select Settings, then Control Panel.
2. Double-click the Network icon.
3. In the Configuration window, select the TCP/IP protocol line that has been
associated with your network card/adapter. (See Figure 3-1.)
These instructions apply only to Windows 95, 98 and Millennium
machines. For TCP/IP setup under Windows NT, Windows 2000,
or Windows XP, please refer to your Microsoft Windows docu-
mentation.
Configuring Your PCs to Connect to the Cable/DSL
Wireless-Ready Router
NNoottee::
If the
TCP/IP protocol
is not config-
ured on your
PC, go to the
Appendix for
TCP/IP installa-
tion instructions
now.
Figure 3-1
Instant Broadband
TM
Series
10
Downloaded from www.Manualslib.com manuals search engine
3. Configure the wireless functions of the web utility using the following
instructions. (Refer to Chapter 6 for more information.)
A. Access the web utility by opening your web browser and typing
http://192.168.1.1 in the browser’s Address box. (This number is the
default IP address of your Router.) Press Enter. (See Figure 4-2.)
B. After entering the address into the web browser, a password request
page will pop up. (See Figure 4-3.) Leave the User Name field empty,
but type admin into the Password field.
C. The basic Setup screen is the first screen you will see when you access the
utility, but is the only one you need to set up your Wireless PC Card.
(See Figure 4-4.) If you have already installed and set up your router, you
have already seen this screen and have already properly configured all of
the screen’s values. More detailed explanations and instructions can be
found by clicking the page’s Help button. To clear any values you’ve
entered, click Cancel and re-enter the information. To apply any set-
tings that you have changed, click the Apply button. Once all settings
are correct, click Continue.
Setup
Figure 4-2
Figure 4-3
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
13
Chapter 4: Adding Wireless
Capabilities to Your Router
Now that your Cable/DSL Wireless-Ready Router is wired into your network,
you can make your Router wireless. You can also wait until a later time. You
will need a WPC11 Wireless PC Card (sold separately.)
1. Power off the Router.
2. Locate the PCMCIA slot on the back of the Router. Insert the Wireless PC
Card into the PCMCIA slot in the direction shown in Figure 4-1. It is very
important to install it with the LEDs facing up and in the correct direction
or damage to the Router can occur. Push the Wireless PC Card into the slot
until it is securely in place.
Make sure to insert the WPC11 Wireless PC Card in the direction
shown in the warning label below.
Figure 4-1
Instant Broadband
TM
Series
12
Downloaded from www.Manualslib.com manuals search engine
Access Control Provides access to your network for other PCs. You’ll need
to enter the MAC Address, then click on Add for any PC that you want to
add. Click on Apply when finished.
Channel Select the appropriate channel from the list provided to corre-
spond with your network settings, between 1 and 11. All points in your
wireless network must use the same channel in order to function correctly.
Verify that the correct channel is selected.
WEP (Mandatory/Disable). In order to utilize WEP encryption, select
Mandatory. If you do not wish do utilize WEP encryption, make sure
Disable is selected. See the Section on Setting WEP Encryption for more
information.
WEP Key Setting When WEP Encryption is Enabled, press this button to
modify the WEP Key Settings. See the Section on Setting WEP
Encryption for more information.
If you haven’t done so already, to apply any settings that you have changed,
click the Apply button. Once all settings are correct, click Continue.
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
15
The following section will provide information on setting up your wireless
connection once you have the Wireless PC Card.
ESSID The ESSID is the unique name that is shared among all points in a
wireless network. The ESSID must be identical for all points in the network.
It is case sensitive and must not exceed 32 characters. Make sure that all
points in the network are the same. Verify that you are using the correct
ESSID.
Figure 4-4
NNoottee::
The
Setup page
shown in this
graphic may
differ from
yours.
Instant Broadband
TM
Series
14
Downloaded from www.Manualslib.com manuals search engine
2. A username and password prompt will appear. Leave the User Name box
empty and type admin (the default password) in the Password box. Click
OK. (See Figure 5-2.)
3. The Cable/DSL Wireless-Ready Router’s Setup page will appear. (See Figure
5-3.)
Figure 5-2
Figure 5-3
NNoottee::
The
Setup page
shown in this
graphic may
differ from
yours.
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
1716
Chapter 5: Configuring Your
Network with the Cable/DSL
Wireless-Ready Router
Configuring the Cable/DSL Wireless-Ready Router
Now that your Cable/DSL Wireless-Ready Router is wired into your network,
you can begin configuring your system.
Note:If your Windows system supports UPnP, Windows will offer to create a
desktop shortcut to the Router. Click OK to create the desktop icon, then dou-
ble-click on the icon to connect to the Router. Otherwise, connect to the Router
manually, as follows.
1. Open your web browser and type http://192.168.1.1 in the browser’s Address
box. (See Figure 5-1.) This number is the default IP address of your Router.
Press Enter.
NNoottee::
If you have previously enabled an Internet Sharing
Proxy Service on any of your PCs, you must disable it now.
• If you are running Netscape Navigator: Click
EEddiitt
>>
PPrreeffeerreennccee
>>
AAddvvaanncceedd
>>
PPrrooxxiieess
> and click
DDiirreecctt CCoonnnneeccttiioonn ttoo tthhee IInntteerrnneett
.
• If you are running Internet Explorer v5 or better, click
SSttaarrtt
>>
SSeettttiinnggss
>>
CCoonnttrrooll PPaanneell
>>
IInntteerrnneett OOppttiioonnss
>>
CCoonnnneeccttiioonnss
>>
LLAANN SSeettttiinnggss
. Remove the checks from all three boxes. Click
OOKK
to
continue.
Figure 5-1
Instant Broadband
TM
Series
Downloaded from www.Manualslib.com manuals search engine
1. Click on the button next to PPPoE.
2. Enter the User Name you use to log on to your Internet connection.
3. Enter your corresponding Password.
RAS (Remote Access Service) is a service used in Singapore only. If you are
using a RAS connection, check with your ISP for the necessary setup infor-
mation.To enable RAS:
1. Click on the button next to RAS.
2. Enter the User Name you use to log on to your Internet connection.
3. Enter your corresponding Password.
RAS Plan Select the type of plan you have.
Connect on Demand (Only available if PPPoE is enabled) If you aren’t
actively using the Internet, you can configure your Router to cut your con-
nection with your ISP after a certain period of time. If you have been dis-
connected due to inactivity, Connect on Demand enables your Router to
automatically re-establish your connection as soon as you attempt to access
the Internet again. Click on the button next to Connect on Demand to
Enable the option.
Keep Alive Option This option keeps your PPPoE-enabled Internet access
connected indefinitely, even when it sits idle. It keeps the connection alive
by sending out a few data packets periodically, so your Internet service
thinks that the connection is still active. To use this option, click on the but-
ton next to Keep Alive to select it.
5. When you have properly configured the Setup page, click Apply, and then
click Continue.
6. Reset the power on the cable or DSL modem, and then restart the com-
puter so the computer can obtain the new Router information.
Your Cable/DSL Wireless-Ready Router is now configured to your net-
work. If you would like, you may continue on to learn more about the
Router’s Web-based Utility.
NNoottee::
Make sure that a Network Card or adapter has been
successfully installed into each PC you plan on configuring
before you continue.
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
19
4. Configure the following values.
Host Name & Domain Name These fields allow you to supply a host and
domain name for the Router. Some ISPs require these names as identifi-
cation. You may have to check with your ISP to see if your Broadband
Internet service has been configured with a host and domain name. In most
cases, leaving these fields blank will work.
LAN IP Address These values refer to your internal network settings.
Unless you have specific internal needs, there should be no reason to
change these values. For the internal LAN, the default values are as fol-
lows.
• Private IP Address: 192.168.1.1
• Subnet Mask: 255.255.255.0
Wireless In this section, enter the ESSID and Channel for your wireless net-
work. You can provide access to your network for other PCs with Access
Control. You’ll need to enter the MAC Address, then click on Add for any
PC that you want to add. Click on Apply when finished. You can decide
whether or not to use WEP Encryption and configure the level of WEP
Encryption. WEP Encryption is not necessary for the operation of your
Router. For more information, see the section of this guide called Setting
WEP Encryption. You must use a wireless PC card (sold separately) to
use this and any other wireless feature.
WAN IP Address These values refer to the outside network you connect to
every time you access your Broadband Internet connection. Most
Broadband ISPs assign their clients a different IP address each time they
log on. If this is the case with your ISP, click Obtain an IP Address
Automatically and continue to step 5. If your ISP assigns you a fixed IP
address, click Specify an IP Address and enter the address into the
Subnet Mask, Default Gateway Address, and DNSfields provided by the
ISP.
Login This section is used if you are using a dial-up style connection like
PPPoE or RAS.
PPPoE (Point-to-Point Protocol over Ethernet) is used by DSL-based
ISPs to establish communications with an end-user. If you are using a DSL
line, check with your ISP to see if they use PPPoE. If they do use PPPoE,
you must enable it by selecting PPPoE in the login section. If you do enable
PPPoE, remember to remove any existing PPPoE applications already on
any of your PCs. To enable PPPoE:
NNoottee::
All of this information should be readily available from your ISP.
Instant Broadband
TM
Series
18
Downloaded from www.Manualslib.com manuals search engine
Setup
p
The basic Setup screen is the first screen you will see when you access the Utility.
If you have already installed and set up your router, you have already seen this
screen and have already properly configured all of the screen’s values.
Host Name This entry is necessary for some ISPs. Ask your ISP.
Domain Name This entry is necessary for some ISPs. Ask your ISP.
Firmware Version This entry shows the version of the firmware you are
using. Future versions of the Router’s Firmware may become available on
the Linksys website.
LAN IP Address and Subnet Mask The IP Address and Subnet Mask of
the router as they are seen on the internal LAN. The default value is
192.168.1.1 for IP and 255.255.255.0 for Subnet Mask. Unless you already
know your settings, we recommend that you keep the defaults.
NNoottee::
The
Setup page
shown in this
graphic may
differ from
yours.
Figure 6-3
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
21
Chapter 6: The Cable/DSL
Wireless-Ready Router’s Web-
based Utility
Quick & Easy Administration
For your convenience, an administrative utility has been programmed into the
chipset of your router. All router-based administrative tasks are performed
through this web utility. The web utility can be accessed by any PC on the net-
work by typing http://192.168.1.1 into the PC’s web browser address window.
(See Figure 6-1.)
After entering the address into the web browser, a password request page will
pop up. (See Figure 6-2.) Leave the User Name field empty, but type admin
into the Password field.
On the following pages you will find brief descriptions and important functions
of each utility web page. More detailed explanations and instructions can be
found by clicking each page’s Help button. To clear any values you’ve entered
on any page, click Cancel and re-enter the information. To apply any settings
that you have changed on any page, click the Apply button. Once all settings
are correct, click Continue.
Figure 6-1
Figure 6-2
Instant Broadband
TM
Series
20
Downloaded from www.Manualslib.com manuals search engine
1. Click on the button next to PPPoE.
2. Enter the User Name you use to log on to your Internet connection.
3. Enter your corresponding Password.
RAS (Remote Access Service) is a service used in Singapore only. If you are
using a RAS connection, check with your ISP for the necessary setup
information.To enable RAS:
1. Click on the button next to RAS.
2. Enter the User Name you use to log on to your Internet connection.
3. Enter your corresponding Password.
RAS Plan Select the type of plan you have.
Connect on Demand (Only available if PPPoE is enabled) If you aren’t
actively using the Internet, you can configure your Router to cut your con-
nection with your ISP after a certain period of time. If you have been dis-
connected due to inactivity, Connect on Demand enables your Router to
automatically re-establish your connection as soon as you attempt to access
the Internet again. Click on the button next to Connect on Demand to
enable the option.
Keep Alive Option This option keeps your PPPoE-enabled Internet access
connected indefinitely, even when it sits idle. It keeps the connection alive
by sending out a few data packets periodically, so your Internet service
thinks that the connection is still active. To use this option, click on the but-
ton next to Keep Alive to select it.
Password
In order for your changes to take effect, click the
Apply button.
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
23
ESSID The ESSID is the unique name that is shared among all points in a
wireless network. The ESSID must be identical for all points in the network.
It is case sensitive and must not exceed 32 characters. Make sure that all
points in the network are the same. Verify that you are using the correct
ESSID.
Access Control Provides access to your network for other PCs. You’ll need
to enter the MAC Address, then click on Add for any PC that you want to
add. Click on Apply when finished.
Channel Select the appropriate channel from the list provided to corre-
spond with your network settings, between 1 and 11. All points in your
wireless network must use the same channel in order to function correctly.
Verify that the correct channel is selected.
WEP (Mandatory/Disable). In order to utilize WEP encryption, select
Mandatory. If you do not wish do utilize WEP encryption, make sure
Disable is selected.
WEP Key Setting When WEP Encryption is Enabled, press this button to
modify the WEP Key Settings. See the Section on Setting WEP
Encryption for more information.
WAN IP Address and Subnet Mask The IP Address and Subnet Mask of
the router as seen by external users on the Internet (including your ISP). If
set to Obtain an IP Address Automatically, these values are assigned by
your ISP.
Default Gateway AddressYour ISP will provide you with the Gateway IP
Address. If set to Obtain an IP Address Automatically, these values are
automatically assigned by your ISP.
DNS (Domain Name Server) IP Address Your ISP will provide you with
at least one DNS IP Address. If set to Obtain an IP Address Automatically,
these values are automatically assigned by your ISP.
You can test and see if the above settings are correct by successfully connect-
ing to the Internet.
Login This section is used if you are using a dial-up style connection like
PPPoE or RAS.
PPPoE (Point-to-Point Protocol over Ethernet) is used by DSL-based
ISPs to establish communications with an end-user. If you are using a DSL
line, check with your ISP to see if they use PPPoE. If they do use PPPoE,
you must enable it by selecting PPPoE in the login section. If you do
enable PPPoE, remember to remove any existing PPPoE applications
already on any of your PCs. To enable PPPoE:
Instant Broadband
TM
Series
22
Downloaded from www.Manualslib.com manuals search engine
3. The following screen will appear, verifying that you are enabling WEP
Encryption. Press the OK button to continue. (See Figure 6-4.)
4. The following screen will appear, where you will choose your WEP
Encryption settings. For the Authentication Type, select Open System
(default setting).(See Figure 6-5.)
5. For the Encryption, choose 64 Bit Encryption or 128 Bit Encryption. The
one you choose must also be used on all your other network devices. Enter
Hexadecimal characters, which are the letters “A” through “F” and the num-
bers “0” through “9” into the fields provided. If you have set a WEP
Encryption on a wireless device on your network, then you must use the
same key set. All devices on a network must use the same key set.
6. Click the Save button, then the Close button and the encryption portion of
the setup is now complete.
NNoottee::
The
screen
shown in
this graphic
may differ
from yours.
Figure 6-4
Figure 6-5
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
25
WEP (Wired Equivalent Privacy) Encryption is a method of encrypting data
that is transmitted over your wireless network to ensure data security. In a wired
network, data security is maintained through the physical wire. WEP
Encryption provides the same level of security for your wireless data as if it
were being transmitted over standard network cabling (which is how the name
is derived). In order to duplicate wired network security levels, wireless data
is encrypted at its point of transmission. It is decoded by the receiving device.
This allows users to have the same amount of security over their wireless net-
work as they would over a wired network. This level of security is above that
already provided by the use of password protection by your network operating
system.
The present standard for this encryption, set by the IEEE (the Institute of
Electrical and Electronics Engineers), is defined as 40-bit (sometimes also
called 64-bit) encryption. Some vendors, including Linksys, offer the higher
128-bit encryption. These numbers refer to the complexity of the algorithms
generated in order to code and decode the data transmitted. The higher the bit
number, the greater the complexity of the algorithm, which is designed to pro-
vide increasingly secure encryption. Be aware, however, that higher levels of
encryption often negatively affect network data transmission rates. This
encryption is not necessary for the operation of your wireless network
device, but is strongly recommended. Your need for security can only be
determined by you. If your security needs are such that ordinary password pro-
tection is sufficient, you may decide not to use the additional WEP Encryption.
However, should your security needs dictate it, the Cable/DSL Wireless-Ready
Router can provide as secure a connection as is available in wireless network-
ing.
1. At the Setup Screen, if you choose to enable WEP Encryption, select
Mandatory under the WEP section.
2. Press the WEP Key Setting button to set the WEP Encryption type and
level.
Setting WEP Encryption
Note: WEP Encryption is an additional data security measure that
is not essential for Router operation, but is strongly recommended.
Instant Broadband
TM
Series
24
Downloaded from www.Manualslib.com manuals search engine
This tab displays the current status of the Router; it reflects data and selections
that you have entered under the setup tab.
All of the information provided on this screen is read-only. To make changes,
select the Setup tab.
Host Name This field shows the name of your Router. This entry is neces-
sary for some ISPs.
Firmware Version This field shows the installed version of the firmware.
Login This field shows whether you have enabled the use of the Router’s
PPPoE support and the status.
LAN These fields display the current IP Address and Subnet Mask of the
Router, as seen by users on your internal network.
•WANThese fields display the WAN IP Address, WAN Subnet Mask, and
WAN Default Gateway IP address of the Router, as seen by external users on
the Internet.
DNS (Domain Name System) IP Address These fields show the IP
Address(es) of the DNS currently used by the Router. Multiple DNS IP set-
tings are common. In most cases, the first available DNS entry is used.
Status
Figure 6-7
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
27
It is strongly recommended that you set a password for the router. When you
first power up the router, you will notice that the Password setting default is
admin.For security, we recommend that you change your password often.
To change your password, enter your new password in the Router Password
box. Enter it again in the box just below the Router Password box, exactly as
you typed it in the first box. When you are sure you have entered the password
as you want it, press the Apply button.
Password
If you set the Restore Factory Default option and click Apply,
you will clear all of the Router’s settings. Do not restore to
the factory defaults unless you want to completely set up the
Router again. Once the Router is reset, you will have to re-
enter your configuration.
Figure 6-6
Instant Broadband
TM
Series
26
Downloaded from www.Manualslib.com manuals search engine
A DHCP (Dynamic Host Configuration Protocol) Server automatically assigns
IP addresses to each computer on your network. Unless you already have one,
it is highly recommended that your router be set up as a DHCP server.
DHCP Server Check the Enable option to enable the DHCP server option
of the router. If you already have a DHCP server on your network, set the
router’s DHCP option to Disable.
Starting IP Address Enter a numerical value for the DHCP server to start
with when issuing IP addresses.
Number of DHCP Users Enter the maximum number of PCs that you want
the DHCP server to assign IP addresses to, with the absolute maximum
being 253.
DHCP Clients Table Click on the Clients Table button to show the cur-
rent DHCP Client information. (This information is stored in temporary
memory, so the list of clients could disappear.)
Help
Help
DHCP
Figure 6-8
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
29
DHCP Release Click the DHCP Release button to release the WAN IP
address from the Router.
DHCP Renew Click the DHCP Renew button to get the new WAN IP
address from your ISP.
DHCP Clients Table Click on the Clients Table button to show the current
DHCP Client information. (This information is stored in temporary memo-
ry, so the list of clients could disappear.)
DHCP
Instant Broadband
TM
Series
28
Downloaded from www.Manualslib.com manuals search engine
Help
Under the Help tab, you’ll find links to all of the Router’s internal support doc-
umentation, including the application that upgrades the Router’s firmware.
New firmware versions are posted at www.linksys.com and can be downloaded
for free. If the Router can access the Internet already, there’s no need to down-
load a newer firmware version, unless that version has a new feature that you
want to use. Loading new firmware onto the Router might not enhance the
speed or the quality of your connection speed.
Figure 6-10
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
31
This tab shows the status of Logging on the Router. If you enable logging, the
Router will keep a record of all sites on the Internet (i.e., e-mail, ftp sites, etc.)
that have been accessed through the Router.
Incoming/Outgoing Access Logs: Here you will specify whether
you want to make a record of Internet sites that have been accessed through
the Router. Both outgoing or incoming addresses can be recorded. (For
instance, if you have a web server, you can keep a record of the sites from
which your web server has been accessed.)
E-Mail Logs: Select Send Incoming Log or Send Outgoing Log.Enter the
Email address and Subject for the log. Add the IP Address of the SMTP
E-Mail Server and the Port Number.
E-Mail Schedule: Choose to send the log When log is full or enter a spe-
cific time. Select the Timezone in the drop-down menu.
• Click the Apply button to save any changes.
Log
Figure 6-9
Instant Broadband
TM
Series
30
Downloaded from www.Manualslib.com manuals search engine
Filters block specific internal users
from accessing the Internet. You
can set up a filter through an IP
address or a network port number.
Filtered Private IPRange
To set up a filter using IP
addresses, enter the range of IP
addresses you wish to filter in
the IP address fields. Users who
have filtered IP addresses will
not be able to access the Internet
at all. If you only want to filter
one IP address instead of a
range of IP addresses, enter the
same value into both fields.
Filtered Private Port Range
To filter users by network port
number, enter a network port
number or a range of network ports. Select the protocol for each port number you
want to filter, TCP or UDP. Enter the port numbers you want to filter in the port
numbers fields. Users connected to the Router will no longer be able to access any
port number listed there.
Editing MAC Filter Setting
This feature filters the network adapter’s specific MAC address from going out to
the Internet.
To check your network adapter’s MAC address, run “winipcfg” or “ipconfig” in
the command prompt. To set the MAC filter, click the Edit MAC Filter Setting
button. When a second window appears, select the range in the drop-down box,
and at the MAC number prompt, enter the 12-digit MAC address you want to fil-
ter. Click the Apply button and then the Continue button before closing the win-
dow.
Block WAN Request
By enabling the Block WAN Request feature, you can prevent your network from
being pinged or detected by other Internet users. The Block WAN Request feature
also adds another measure of security to your network by hiding your network
ports. Both functions of the Block WAN Request feature make it more difficult for
outside users to work their way into your network.
Filters
Figure 6-12
EtherFast
®
Cable/DSL Wireless-Ready Router with 4-Port Switch
33
This screen shows the Universal Plug and Play services that are available.
Microsoft ME and XP feature Universal Plug and Play (UPnP), which allows
automatic discovery and configuration of equipment attached to the LAN.
UPnP allows enabled applications to automatically manage the router.
There are two ways to begin the UPnP configuration. Choose one:
Double-click My Network Place. Then double-click the Linksys
BEFSR41W icon.
• Or, start your Web interface. Type in the address http://192.168.1.1.
Using either method, you will see the Setup tab. Click theAdvanced tab. Then
click the UPnP tab.
On the UPnP tab, you have three features to choose from:
Enable UPnP Services This allows Windows XP to activate the UPnP fea-
ture for automatic configuration.
Allow users to make configuration changes through UPnP This allows
you to make manual changes while still using the UPnP feature.
Allow users to disable Internet access This allows you to prohibit any and
all Internet connections.
Click Apply to accept changes, or click Cancel to cancel changes.
UPnP
Figure 6-11
Instant Broadband
TM
Series
32
Downloaded from www.Manualslib.com manuals search engine
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Linksys BEFSR41W Owner's manual

Category
WLAN access points
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI