• Fitting: Die Cast Aluminium with White nish.
• Lamp type: Excluding 1 x GU10 max 50W 220V-240V
•Voltage: 220V - 240V ~ 50Hz
• Protection against electric shock: Class 1. Requires earthing.
•IP Rating: IP22. Protected against solid foreign objects of 50mm Ø and greater.Protected
against vertical falling water drops when enclosure is tilted up to 15°.
•Commercial/domesticuse
•Notsuitableforoutdooruse
• Maximum Ambient temperature range: 20ºC - 40ºC.
• Dimensions:(D)104mm x (Ø)83mm
• Cut-out: (Ø) 74mm
D62 - attachments:
Iftheexternalexiblecableorcordofthisluminaireisdamaged,itshouldbeexclusivelyreplaced
bythemanufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.To
ensure that you get maximum longevity and maximum use out of your luminaire, please observe
the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire
mustbecarriedoutbyaqualiedelectrician,inaccordancewithSANS10142.Oncompletion
ofinstallation,ensurethattheCerticateofComplianceisupdated.
•Beforeconnectingtheluminaire,ensurethatvoltageindicatedontheratinglabel
corresponds with the mains voltage in your home.
•Whenchangingthelamp,ensurethatthepoweristurnedoff.
•Ensurethatthecorrectlamptypeandwattageistted.
•Thisluminaireischeckedinfullforconformitytothequalitystandardsandsafetyrequirements.
•Themanufacturer/supplierisnotresponsibleforanydamageofpropertiesandpersons,
caused by the incorrect use or installation of the luminaire.
•Shouldyoubeunsureofhowtoinstallthisluminairecorrectly,pleaseconsultaprofessional
electrician or your supplier for assistance.
•Ensureallitems/components,threadsandscrewsaretightlysecured.
IMPORTANT:
•Tamperingwiththisluminaire,I.E.Usingsiliconsealersorincorrectcabling,willinvalidate
your warranty.
•Whentheprotectionglassisdamaged,itshouldbereplacedimmediately.
•Pleasecheckwhethertheconnectionofthepowercordissafeandreliablebeforeinstallation.
•Ifyourmainswiringdiffersinanywayfromdiagram,consultaqualiedelectrician.
•Alwaysensurethatthemainssupplyvoltageiscorrect.
•Alwaysreplacethelampwithoneofanidenticalratingandwattage.
•Chokinghazard:Maycontainsmallparts.Keepawayfromchildren.
•Donotinsertyourngersoranypartofyourbodyintotheelectricalcontactandsocketsof
this product whilst it is connected to the electrical supply.
•Itemmayvaryslightlyfromthepictureonthecarton.
SPECIFICATIONS
IMPORTANT SAFEGUARDS
Before installation always ensure the power supply is turned off.
1.Cut a hole in the ceiling as per “cut out”.
2.Connect to electrical supply.
3.Hold both clips on either side of downlight upwards and insert downlight into ceiling hole
ensuring the mains lead is not trapped.
4.Pushttingupwardstosnaprmlyintoposition,ushwithceiling.
5.Insert the lamp by locating the pin connection holes within the lamp
holder, gently pushing the lamp into the holder and twisting into place.
6.Reconnect power.
NOTE:Alwaysallowthelamptocoolsufcientlybeforechanging.
NOTE:To avoid heat transfer from downlight, allow a minimum gap of
about200mminheightfromdownlighttoceiling/anymaterialsabovethedownlightand50mm
all around the sides of the downlight.
Failuretodosocouldresultinre.
INSTALLATION
CLEANING
•Beforecleaningalwaysensurethepowersupplyisturnedoff.
•Donotimmersetheluminaireinwater.
•Noabrasiveproducts,solvents,detergentmaybeusedtocleanthisluminaire.
•Ensurethatthettingdoesnotcomeincontactwithcorrosivechemicals,etc.
•Useasoftclothtoclean.