There is no guarantee that all equipment will work. Some devices may not work
Security considerations
Do not bring strong vibration and shock to this product, do not bring harm to this product. This product shall not be
used and kept in water or in places with water, direct sunlight, high temperature and humidity, dust or fumes, etc. When
reseating this product, you must have the necessary connector parts, reseat straight. Stretch the cable portion. Excessive
force can lead to damage or failure. Please don't step on this product with furniture. Please do not let the child remove
this product and accessories down If the casing is damaged, the connector is rocking, etc., stop using the new cable.
This product should not be broken down, repaired, processed and modified. The Company shall not be liable for direct
or indirect damage to this product due to reason or its use. Please understandThis product is for indoor use. Do not use
it outdoors. This product is suitable for these purposes. If personal injury, social barriers, etc., the company will not be
responsible.
Questions And Answers
If the above has not solved your problem, please contact our customer service
E-Mail:[email protected]
Fiber Optic 8K DisplayPort Cable
Instruction Manual
https://www.cabledeconn.com
www.deconncable.com
1. Q: what is the difference between a fiber-optic DisplayPort AOC CABLE and a traditional DisplayPort
copper cable
A: fiber-optic DisplayPort AOC CABLE basically does not attenuate, so the signal is more stable and
transmitted further. 60% less copper than copper wire.
2. Q: how to achieve a standard DP1.4 HBR3 transmission effect, Confirmation of output and input devices
A: Resolution 7680x4320, Refresh rate 60Hz, DSC(Display stream compression), Bandwidth: 25.92Gbit/s
Resolution 3840x2160, Refresh rate 144Hz, DSC(Display stream compression), Bandwidth: 25.92Gbit/s
Resolution 3840x2160, Refresh rate 240Hz, DSC(Display stream compression), Bandwidth: 25.92Gbit/s
3. Q: how to properly connect fiber DisplayPort AOC CABLE
A:Refer to the connection direction of the above figure
4. Q: DisplayPort AOC CABLE for bending radius, stampede, winding and other requirements during use
A: refer to illustration 4 above.
5. Q: when the DisplayPort AOC CABLE connects both ends of the device, no signal output, and the device
does not work
A: 1. Ensure proper connection to this connection line 2. Ensure that both ends of the equipment are working
6. Q: when the DisplayPort AOC CABLE is connected to a transit device (switch, distributor, amplifier),
there is no signal output
A: 1. Does the transit device support resolution for both ends of the device, and if it is not supported, it
cannot play back
2. If the direct-plugged fiber DisplayPort AOC Cable works, if it works, it means that my cable is good.
7. Q: can you get a 1080p HD signal instead of a 4K UHD signal
A: check that your output and input devices support 4K
8. Q: when the DisplayPort AOC CABLE connects both devices and does not support 4:4:4 video format
A: check that your output and input devices support 4K 4:4:4
9. Q: when the DisplayPort AOC CABLE is connected to both devices and an intermittent flash screen appears
A: check to see if the cable is loose or that you have problem
10. Q: when the DisplayPort AOC CABLE connects the devices at both ends and the screen appears?
A: check to see if the cable is loose or that you have problem
11. Q: when DisplayPort AOC CABLE connects devices at both ends, SDR and HDR switching are abnormal?
A: this connection cable supports HDR, you can try reseating this connection cable
12. Q: when the DisplayPort AOC CABLE connects devices at both ends, image and sound jitter
A: check to see if the cable is loose or that you have problem
8K
DP-HBR3
Display
8K
DP-HBR3
Source
Product Description
Product Parameter
Connection direction
Notice the name of the connector
PC
Set-Top Box Game console TV Projector Display
Source Display
Matters Need Attention
1. When handling
setting up, do not let the fiber-optic cable be affected by great impact
and side pressure, so that the shell itself will be deformed, which may cause the fiber to be
stuck when in use, and the resolution will be reduced. Or there may be the worst interruption.
In addition, after construction wiring will also occur broken line, so need to pay attention.
2. Check the appearance and performance of the optical fiber before installing the wiring.
Please test the reconstruction on the equipment you need to use to avoid unnecessary
trouble at the later stage.
3. When wiring, please be careful not to tie, or pull the fiber
, or use feet and other heavy
objects to press the fiber, the process of breaking through the wall should not be more than
200N, if the fiber is broken, or the core broken, the optical fiber can no longer be used.
4. The optical fiber should have a small amount of surplus at the turning point, make a good
drop bend at the corner, do not let the optical fiber touch sharp objects, the surplus optical
fiber should be wound reasonably and beautiful, when winding the fiber, the force should be
uniform, and the optical fiber should not be subjected to hard bending. So as not to damage
the fiber.
5. When moving, use a line card to be fixed firmly, one at a distance of 1: 15 meters, do not
stretch too much between fixed positions, leaving room for thermal expansion and
cold shrinkage, and in addition, in order to prevent damage to the optical fiber in the
vertical alignment, stick tape between fixed line cards once.
Preface
Minimum
bending radius
Cable
disk round
Min
Direction
of dressing
To prevent deterioration and breaking of the internal fiber, always ensure
minimum bending semicircle. When laying, because you pull the cable,
pay attention to torsion and tension to ensure that the bending radius is
above 40mm.
When laying the cable, pay attention to the angle of the machine, etc.,
be careful not to touch the sharp angle of the machine and equipment.
Note when reseating the DP connector. When inserting or removing
the connector, gently insert it with the connector part. If tension or force
is applied, it may lead to breakage, broken wires, faults.
Be careful not to twist the cable and do not
apply tension on the internal fibre Channel
while loosening the cable.
The DP connector cannot be suspended, the connector's junction
will be deformed, and the internal fiber may be disconnected.
When handling excess cables, follow the circle winding above the
diameter of 80mm and do not apply pressure to the connector
junction.
Thank you for your purchase. Please read this manual carefully before use. Please use it
according to the content. Please keep this instruction after reading!
This fiber optic DisplayPort cable can transmit the sound of the computer and laptop through
DisplayPort interface to the TV, display and projector with DisplayPort interface, and transmit
a maximum length of 300 meters, the resolution can reach 8K@60Hz.
•Color: Black
•Connector Type: Standard DisplayPort Type plug
•Highest bandwidth : 32.4Gbps (HBR3 8.1Gbit/S per Lane)
•Resolution: 4K(3840x2160)@240Hz / 8K(7680x4320)@60Hz (Downward compatibility)
•Conductor Material: Tinned Copper+Fiber
•Shell Material: Zinc Alloy
•Shielding: Aluminum Foil+Metal Woven Mesh
•Jacket Material: TPE
•Length:2M / 3M / 5M / 10M / 15M / 20M / 30M / 50M / 100M
The plug and play, without external power supply or signal amplifier, Support Simplified Color
Profile . Small barren waist streamlined metal shell, in line with ergonomics. Fiber-optic
transmission of high-frequency signals, no electromagnetic interference. The outer diameter
4.6mm photoelectric composite cable structure, the wire rod light convenient engineering wiring.
8K
DP-HBR3
Source
Source:Connect signal output device, such as Set top box, DVD, PC and Game console.
Display:Connect signal input device; such as TV, Projector, Display.
Note: the insertion direction error will cause the
signal to be unable to transmit
4K
DP-HBR3
Source
4K
DP-HBR3
Display
8K
DP-HBR3
Source
8K
DP-HBR3
Source
8K
DP-HBR3
Source
8K
DP-HBR3
Source
8K
DP-HBR3
Source
/