https://kuppet.mobi/
MADE IN CHINA
Read all instructions before using the appliance.
● T o reduce the risk of injury, close supervision is required when an appliance is used near
children.
● D o not put fingers or hands into a waste disposer.
● W hen attempting to remove objects from a waste disposer, use long-handled tongs or pliers.
● D o not dispose of the following in the disposer: clothing, household cleaners and chemicals,
automotive fluids, plastic wrap.
● C l ean drain line before installing disposer. Failure to clean sink drain line may result in drain
line blockage. With drain auger, clear all hardened waste material in horizontal drain line.
● T u rn the power switch to the off position before attempting to clear a jam, removing an object
from the disposer or pressing reset button.
● R e gularly inspect disposer and plumbing fittings for water leaks, as water leaks can cause
property damage. Manufacturer cannot be held responsible for property damage as a result
of water leaks.
● E l ectric Shock: Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the appliance is properly grounded. Do not modify the plug provided with the
appliance - if it will not fit the outlet , have a proper outlet installed by a qualified electrician.
● This disposer must be properly grounded.
● Disconnect power before installing or servicing disposer.
● If three-prong grounded plug is used, plug must be inserted into three-hole
grounded receptacle.
● All wiring must comply with local electrical codes.
● Do not reconnect electrical current at main service panel until proper grounds are installed.
If you have questions or concerns, please visit our website at for more https://kuppet.mobi/
information.
Loosen the three screws
on the mounting assembly,
get them out about
0.6 - 0.8 inch (15-20mm).
Use a flat head screw to
take out the snap ring (I),
then separate the paper
gasket (E), metal gasket (F),
and mounting ring (G) from
the assembly.
Take out the paper gasket (E)
and put it aside, put the
gasket (D) onto the sink
flange (C), then press it firmly
onto the sink drain as shown.
Evenly apply 1/2" thick rope of
plumber's putty around sink
flange (C).
Put the disposer on top of
the sink flange (C) to hold
it in place, use a towel to
prevent scratching the sink.
Insert paper gasket (E),
metal gasket (F), and
mounting ring (G).
Press snap ring (I)
firmly in place.
Tighten the three
mounting screws (H)
evenly and firmly against
the flange.
2
1
Plumbers putty
3
5
6
4
Disposer
Stopper
Sink Flange
Gasket
Paper Gasket
Metal Gasket
Mounting Ring
1 1/2" Screws
Snap Ring
ss304
Sink Baffle
Lower Mounting Ring
Dishwasher Inlet
Water Outlet
Wrench
Rubber Ring
Water Outler Ring
L Tube
Screws
Tools and Materials (not included)
Plumbers putty
Water Outler Ring
o
Warranty
Length of Warranty by Model: please visit our website at https://kuppet.mobi/
for more information.
This warranty covers all replacement parts and repair labor to correct
defects in disposer material and workmanship for the full warranty period
from the date of installation in your home. If warranty service is required
during the warranty period, contact our service to replace or repair the
unit in your home at no cost to you. If you have questions concerning your
disposer or determining when service is needed,
please visit our website at .https://kuppet.mobi/
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If the manufacturer determines the
unit should be replaced rather than repaired, the warranty on the
replacement unit will be limited to the unexpired term of the original
warranty.
If your disposer does not operate, follow these steps in order:
1. Check the things you can do yourself. Be sure the disposer is connected
to the electric power and the fuses or circuit breakers are in working order.
Reread the instruction book to ensure that you are operating the disposer
correctly.
2. Visit our website for information at .https://kuppet.mobi/
When writing, supply the following information:
Date, your name and your phone number. Describe the product by model
number, serial number, date purchased, place purchased, and service history.
Clearly describe the problem and service required.
NOTE: Warranty is determined by unit serial number and date of installation.
Purchase receipt may be required to verify warranty status.
The foregoing warranty does not apply to damage or in-operation resulting
from accident, alteration, misuse,
Warranty will be voided if installed in a commercial or industrial application.
Troubleshooting
Before seeking repair or replacement, we recommend that you review the following:
LOUD NOISES:
There might be an accidental entry of a spoon, bottle cap or other object.
To correct this, turn off electrical switch and water. After disposer has stopped,
remove object with long handled tongs.
UNIT DOES NOT START:
Unplug power cord or turn either the wall switch or breaker box switch to “OFF”
position. Insert one end of self-ser vice wrench into center hole on bottom of disposer
(see Figure A), work wrench back and forth until it runs one full revolution. Reach into
disposer with tongs and remove object(s). Push the red reset button on disposer
bottom (see Figure B).
LEAKS: If the unit leaks at the top, it may be due to:
1. Improper seating of sink flange (gasket centering, putty or tightening).
2. Support ring not tightened properly.
3. Defective or improperly installed cushion mount. If unit leaks at the waste elbow,
leak may be due to improper tightening of elbow flange screws.
DO NOT ATTEMPT TO LUBRICATE YOUR DISPOSER!
The motor is permanently lubricated. The disposer is self-cleaning and scours its internal
parts with each use. NEVER put lye or chemical drain cleaners into the disposer, as they
cause serious corrosion of metal parts. If used, resulting damage can be easily detected
and all warranties are void. Mineral deposits from your water can form on the stainless
steel turntable, giving the appearance of rust.
DO NOT BE ALARMED, the stainless steel turntables used will not corrode.
Https://kuppet.mobi/
E-mail: K U PP E T S t o r e 20 1 8 @ h o t m ai l . c o m
！
Turn disposer onto side and
insertscrewdriver into
dishwasher inlet.
Knock out drain plug and
removeplug from inside of
disposer.
Place dishwasher tube into
dishwasher Inlet. Secure with
hose clamp.
Hang disposer by aligning 3
mounting tabs with slide-up
ramps on mounting ring.
Use the wrench (J) to secure
the mounting ring tightly.
*CAUTION: DISHWASHER CONNECTION ONLY.
If you do not need to attach the dishwasher, go to step 11.
Install the rubber ring (K)
onto the tube (L),
then secure the tube to
disposer with screws.
11
7
9
10
12
You may need to trim
discharge tube to ensure
proper fit. Make sure
anti-vibration tailpipe
mount is straight.
Test for leaks after
Installation:
Fill 2/3 of the sink with tap
water, turn on the disposer
and then release the water.
Check for leaks on
connections spots (#1) and
(#2) as indicated on the
picture.
13
8
14
1#
2#
Made in China
/
