Ash Grove 160.75.AG provides a great canvas for your architectural vision. Its strong, durable and long-lasting mortar bond makes the device suitable for intermediate strength masonry uses such as laying block, brick, or stone, making stucco or plaster, and making mortar repairs. The device is easy to mix, finish, and cure, thanks to its enhanced setting time, workability, water retention, durability, and bond.
Ash Grove 160.75.AG provides a great canvas for your architectural vision. Its strong, durable and long-lasting mortar bond makes the device suitable for intermediate strength masonry uses such as laying block, brick, or stone, making stucco or plaster, and making mortar repairs. The device is easy to mix, finish, and cure, thanks to its enhanced setting time, workability, water retention, durability, and bond.
masonry type S cement
Ash Grove MASONRY-CMNT-S Copyright 2011 Ash Grove Packaging, Inc. 27911
1. Product Name
ASH GROVE® Masonry Type S Cement
Product Number: 160
2. Manufacturer
ASH GROVE PACKAGING GROUP
10809 Executive Center Drive, Ste. 321
Little Rock, AR 72211
Phone: (888) 289.1117
Fax: (501) 224.3882
www.ashgrovepkg.com
3. Product Description
ASH GROVE® Masonry Type S Cement is formulated to
provide a mortar with enhanced setting time, workability,
water retention, durability and bond. ASH GROVE®
Masonry Type S Cement achieves high strength and
mechanical resistance. Ideal for use in load bearing walls
or wherever higher adhesion, greater compressive and
flexural strengths are needed.
BASIC USE:
Recommended for intermediate strength masonry uses
such as:
Laying block, brick, or stone
Making stucco or plaster
Making mortar repairs
COMPOSITION & MATERIALS:
ASH GROVE® Masonry Type S Cement is a premium,
high quality masonry cement designed and manufactured
for use in mortar for masonry construction. The cement is
a mixture of portland cement, finely ground mineral
materials and special admixtures.
4. Advantages/Benefits
ASH GROVE® Masonry Type S Cement has several
advantages including:
Applicable for above or below grade interior and
exterior construction
Higher mechanical resistance than Type N mortar
Strong, durable and long-lasting mortar bond
Easy to mix, finish and cure
5. Preparation
All surfaces that will be in contact with masonry mortar
should be entirely free from oil, grease, or any other foreign
substances which may interfere with the bond of the mortar
to the masonry.
Prior to laying brick, block or stone dampen the exposed
surfaces and clean thoroughly with water. Make sure that
all supportive footings are substantial to hold the stress
load.
For mortar repairs chisel out mortar joints to ¾” depth.
Remove all loose mortar and sand and dampen the
cleaned joint with water prior to application of masonry
mortar mix.
6. Mixing Instructions
Masonry cement is designed to be combined with sand and
water in order to produce a masonry mortar mix.
For Type S Mortar Mix (Intermediate Strength; ASTM C-270):
Mix 1 part ASH GROVE® Masonry Type S Cement and
2¼ - 3 parts sand (ASTM C-144).
For colored mortar, ASH GROVE® Cement Color can be
added and mixed thoroughly into the dry mortar-based
material prior to adding water to achieve decorative and
creative colors. Available colors are red, black, buff and
brown.
Then, add adequate amounts of water to achieve desired
workability and consistency. Avoid a ‘soupy’ mix; too much
water will weaken the mortar.
The mortar should be mixed for 3 to 5 minutes after all
materials are in the mixer. Use of a machine mixer is
recommended to ensure all ingredients are thoroughly
combined.
7. Placement
For laying brick, block or stone:
Starting in a corner, apply approximately ½” thick bed of
mortar to the base. Set corner brick, block or stone into the
mortar bed and tap into place. Lay successive masonry
units into position after first applying mortar to the head
joint and tap into place, maintaining at least 3/8” thick
mortar joint.
For mortar repairs:
Use a tuck-point trowel or jointing tool to apply mortar on
the brick, block or stone and compact.
8. Curing
Clean all excess mortar off the brick and block faces as
soon as possible. Use a jointing tool to smooth and seal
the mortar joints after the joint becomes thumbprint hard.
Doing so will make the joint watertight and provide a neat
appearance. In very hot and dry weather conditions, spray
water onto joints to prevent premature drying of the mortar.
9. Technical Information
ASTM SPECIFICATIONS:
Meets requirements of ASTM C-91 specifications for
Type S Cement when used as directed.
masonry type S cement (cont.)
Ash Grove MASONRY-CMNT-S Copyright 2011 Ash Grove Packaging, Inc. 27911
2
10. Limitations
Adhering to the specified amounts of water additions and
properly graded sand meeting ASTM C-144 specifications
is very important. Exceeding maximum recommended
amounts per bag or using incorrect types of sand will result
in inferior physical properties.
Mortar mixes will not bond well to wood, asphalt, or any
other foreign substances.
Sand sources and proportions should remain the same
throughout the entire project.
Do not place when temperatures are below 40º F or if
temperature is expected to fall below freezing within a 48-
hour period.
11. Coverage
75 lb. bag (34.0 kg)
12. Warning
ASH GROVE® Masonry Type S Cement contains cement.
Normal safety wear such as protective clothing, boots,
rubber gloves, dust masks, eye safety glasses should be
worn while handling cement-based products. Material
Safety Data Sheets are available upon request or at
www.ashgrovepkg.com.
13. Limited Warranty
This product meets or exceeds applicable ASTM C-91
standards in force at the time of packaging. Packager,
having no control over the use of the material, does not
guarantee finished work. Replacement of any defective
product or refund of the purchase price of defective product
shall be the buyer’s sole remedy under this warranty.
THIS LIMITED WARRANTY EXCLUDES ANY LIABILITY
FOR ANY CONSEQUENTIAL, INCIDENTIAL, INDIRECT
OR SPECIAL DAMAGES.
EXCEPT FOR THE LIMITED WARRANTY MADE ABOVE,
PACKAGER SPECIFICALLY DISCLAIMS AND
EXCLUDES ANY OTHER EXPRESS WARRANTY, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OF
GOODS AND ANY IMPLIED WARRANTY OF FITNESS
OF GOODS FOR ANY PARTICULAR PURPOSE.
Ash Grove Packaging reserves the right to change
specifications without notice.
-
1
-
2
Ash Grove 160.75.AG provides a great canvas for your architectural vision. Its strong, durable and long-lasting mortar bond makes the device suitable for intermediate strength masonry uses such as laying block, brick, or stone, making stucco or plaster, and making mortar repairs. The device is easy to mix, finish, and cure, thanks to its enhanced setting time, workability, water retention, durability, and bond.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Ash Grove Pro Mix 612.80.AG Installation guide
-
Hilti CFS-M BAS User guide
-
Sika 187782 User guide
-
Riverside 100069997 Installation guide
-
Titan Florida 100019 Installation guide
-
Brixment 65150084 Installation guide
-
Cemex BRIXMENT S Installation guide
-
Amerimix 62300001 Installation guide
-
Isokern STANDARD 42 Owner's manual
-
Isokern Magnum 28 Installation, Operation, Maintenance And Owner's Manual
