Speakman SA-1203 Installation guide

Speakman
Brand
Speakman
Model
SA-1203
Type
Installation guide

Speakman SA-1203

The Speakman SA-1203 is a solidly built towel shelf. Its simple design makes it easy to install following just a few steps, and it can be mounted at any height you wish. The product is made of durable materials to provide years of trouble-free performance. Regular maintenance is minimal and can be done with the use of a soft cloth.

Speakman SA-1203

The Speakman SA-1203 is a solidly built towel shelf. Its simple design makes it easy to install following just a few steps, and it can be mounted at any height you wish. The product is made of durable materials to provide years of trouble-free performance. Regular maintenance is minimal and can be done with the use of a soft cloth.

INSTRUCTIONS FOR MODELS
92-SA-1203-01
For additional assistance or service please contact:
SPEAKMAN
®
Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
SA-1203
HELPFUL TOOLS & SUPPLIES:
TOOLS AND SUPPLIES
Pencil Measuring
Tape
Level
Drill
Tile Drill Bit
7mm
Drill Bit
7mm
Phillips
Screwdriver
Stud Finder
Hammer
Additional warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives on any of the Speakman custom
finish products may damage the finish and void the
product warranty. Please be sure to only use approved
cleaners. Please contact Speakman for any clarification
of acceptable cleaners.
Speakman
Speakman
Speakman
Speakman
1
At the selected height, mark center point of
mounting locations onto wall referencing the
rough in diagram.
21¼”
540mm
2
Align Mounting Plate as shown below. Mark
Mounting Screw locations onto the wall surface.
Remove items after marking mounting locations.
2X
3
钻
钻
Select proper drill bit for mounting location. Drill
7mm holes in marked locations.
Ø7mm
2X
4
Insert Plastic Anchors into drilled holes and tap lightly with Hammer to fully seat Plastic Anchor into the hole.
2X
5
Insert Screw (1) through Nylon Washer (2), Mounting Plate (3), Isolating Gasket(4), and secure assembly to
Plastic Anchor (5).
2X
䐭
6
Install Clear Plastic Gaskets over Mounting Flange of Towel Shelf.
2X
䐭
7
Install Accessory over Mounting Brackets and Secure with Set Screw.
2X
SA-1203 REPAIR PARTS
SPEAKMAN
®
RPG05-42056 MOUNTING HARDWARE GROUP
ITEM NO. PART NO. DESCRIPTION
SA-1203 ROUGH-IN DIAGRAM
SPEAKMAN
®
DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.
21
1
4
"
540mm
23
3
4
"
603mm
5
8
"
16mm
1
3
4
"
44mm
4
15
16
"
125mm
7
3
4
"
197mm
3
8
"
10mm
  • Page 1 1
  • Page 2 2

Speakman SA-1203 Installation guide

Speakman
Brand
Speakman
Model
SA-1203
Type
Installation guide

Speakman SA-1203

The Speakman SA-1203 is a solidly built towel shelf. Its simple design makes it easy to install following just a few steps, and it can be mounted at any height you wish. The product is made of durable materials to provide years of trouble-free performance. Regular maintenance is minimal and can be done with the use of a soft cloth.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers